Belkin Routers :: N750 Required Settings For Cisco DPC3008 Modem
Jan 20, 2013
Recently switched DSL providers and now have Cisco modem DPC3008. Able to connect to internet directly thru modem. Able to connect wired or wireless to router. Unable to get router to connect to internet via modem. Tried restart, reset, and new set-up. Called ISP (Charter) - no way, said contact Belkin.
I had an WRVS4400 (but didn't use the wireless), it it died. I'm replacing with an RVS4000. I have all the settings from the prior router, but my question has to do with the DSL modem in use in conjunction with the router, because (in my absence) my wife had a conversation with SBC, trying to use the hook to the modem directly and ended up altering settings on the modem that may affect the RVS4000 when I go to install it upon its receipt from Amazon tomorrow.
We have a business that uses a third party software vendor's website; their servers access our data on our server behind the router. So we use a static IP address, and port forwarding. No problem there. But I could have sworn that, with the WRVS4400 we used to have the modem configured as bridged; as of this morning, the modem shows PPPoE, and my wife can't recall what SBC had her do in that regard!
So, for the situation I've described, should I put the modem into bridge mode (and porting it into the RVS4000). Like I said, we have a static WAN IP address, and a range of more static IP addresses.
N750 DB USB printer not connecting. I'm currently running a Canon MP480 multi-purpose printer connected through USB to the N750 DB router. I have both the printer driver and Belkin USB Print and Storage Manager software installed on a desktop PC that connects wirelessly to the router. The Belkin print manager software "sees" the printer, but when I try to connect it says please install printer drivers. I've installed and re-installed these drivers a few times, with no effects.
My N750 F1103 (f/w 1.10.16) LAN speed is limited to 5Mb why? I upgraded my Internet bandwidth to 20Mb+ tested and found it was only 5Mb, the cable company checked a few things and then I did some diagnostics and Isolated to the N750. I have two wired PC and same results with both PC's. This is supposed to have Giga bit LAN not Giggle bit LAN! I'm paying for something I cannot used to its full potential.
I have a N750 and I want to change the IP address through the browser. It is the standard 192.168.2.1 config. I change the IP to 192.168.15.x while hard wired and hit apply. The router reboots but still holds the same IP.
I cannot airprint. Contacted email support. Followed instructions to reset router. I did and I was able to print from my iPhone. ONCE. Then I installed my SSID and passwords and WIFI setup again and now I can't print. I have a brand-new airprint equipped HP 7520, an iPhone and 2 iPads.that I want to print from....the router is a N750 AV bought in July.
I have a belkin N750 DB router. I recently upgraded by internet service from 15Mbp to 30Mbp. If I connect my computer directly to the cable modem, I get 30Mbp throughput. However, if I connect the modem to the router my speed drops to 15Mbp. How do I get the router to support 30Mbp?
My ISP is Comcast and I own a Belkin N750 DBWireless N+ Router, I have a Synology NAS drive wired to the router. I am trying to set up the network configuration on the NAS drive so I can have internet access to the drive. My question is do I manually define the IP address, subnet mask, DNS, and gateway or do I select DHCP. If so what addresses should I use the address of the NAS drive form the router or the router address. I think I need to use the manual fields and use a static IP but do I get that IP address from the router or from my ISP (comcast)?
I have a n750 and I did the firmware update on the router and I have it check for firmware updates when I log in and i keep getting this message: "Cannot connect to the firmware information server,please double check the WAN connection." I have access to the internet.
How do I utilize the dual band feature on my belkin N750 DB? Do I have to set up two separate networks? Even then how when my devices PC, iPod, gaming devices are only recognizing the 2.4GHz band network?
I just bought a N750 DB router. On boot up, the 5Ghz side will show up for about 20-30 seconds and then it just "disappears". I was even able to connect to it @ 300mb with my laptop. The 2.4Ghz shows up just fine.
I have a Western Digital Mybooklive 3Tb hard drive connected to my N750 wireless router. It works fine, except that the new Media Server and the USB print and storage center says there are no USB devices plugged into it! Why is this?
I have an N750 DB router and it has been rebooting every few hours for no reason. This has just started happening about 4 days ago. I don't know why but when I check the system logs its filled with the following. [code]
Belkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.
I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
I have an issue with my N750 Wireless router, F9K1103. I have a Windows Home Server, HP Media Smart Server – EX470, that at times causes the router to lose connection, with the front panel light going from Blue (connected) to Orange (disconnected). When I pull the net cable from the server, after about 30 seconds the blue light comes back on.
i lost my belkin n150 installation cd, and i haven't installed it on my computer, my net connection to my computer via lan keeps dying, but wi-fi works perfectly. What should i do? Where can i download the software from??
After our ISP had a network outage, our Belkin N150 stopped working properly & now I can't get to the Settings page to fix anything. I have used the Reset feature to no avail. The blue light is on but the "Fixit" feature only comes up with something about the ASDL line.
Earlier today I put in a password for my Belkin_G_Wireless_CC7A57 router. I had to change something, im not sure what it was. it was like WPA or WAP. now it wont let me go to my router settings 192.168.2.1 in the address bar is how i have been getting to it. now it just takes me to a OOPS google chrome cannot open this web page..... I just want to restore the router to it factory default settings. it will let this laptop on and another one in the house but not an older one we have which runs Windows XP. If i can get to my router settings i will be fine..