Belkin Routers :: N750 AV Cannot Airprint With HP 7520
Dec 27, 2012
I cannot airprint. Contacted email support. Followed instructions to reset router. I did and I was able to print from my iPhone. ONCE. Then I installed my SSID and passwords and WIFI setup again and now I can't print. I have a brand-new airprint equipped HP 7520, an iPhone and 2 iPads.that I want to print from....the router is a N750 AV bought in July.
I bought a Canon Pixma mg3220 all in one printer/scanner today. I specifically picked it for the Airprint feature for my IPhone, which I can't get to work. Is it a problem with my F5D7234-4 v5 router? I have updated the firmware and it still won't print. The Iphone sees the printer, but that's as far as I get.
N750 DB USB printer not connecting. I'm currently running a Canon MP480 multi-purpose printer connected through USB to the N750 DB router. I have both the printer driver and Belkin USB Print and Storage Manager software installed on a desktop PC that connects wirelessly to the router. The Belkin print manager software "sees" the printer, but when I try to connect it says please install printer drivers. I've installed and re-installed these drivers a few times, with no effects.
My N750 F1103 (f/w 1.10.16) LAN speed is limited to 5Mb why? I upgraded my Internet bandwidth to 20Mb+ tested and found it was only 5Mb, the cable company checked a few things and then I did some diagnostics and Isolated to the N750. I have two wired PC and same results with both PC's. This is supposed to have Giga bit LAN not Giggle bit LAN! I'm paying for something I cannot used to its full potential.
I have a N750 and I want to change the IP address through the browser. It is the standard 192.168.2.1 config. I change the IP to 192.168.15.x while hard wired and hit apply. The router reboots but still holds the same IP.
I have a belkin N750 DB router. I recently upgraded by internet service from 15Mbp to 30Mbp. If I connect my computer directly to the cable modem, I get 30Mbp throughput. However, if I connect the modem to the router my speed drops to 15Mbp. How do I get the router to support 30Mbp?
My ISP is Comcast and I own a Belkin N750 DBWireless N+ Router, I have a Synology NAS drive wired to the router. I am trying to set up the network configuration on the NAS drive so I can have internet access to the drive. My question is do I manually define the IP address, subnet mask, DNS, and gateway or do I select DHCP. If so what addresses should I use the address of the NAS drive form the router or the router address. I think I need to use the manual fields and use a static IP but do I get that IP address from the router or from my ISP (comcast)?
I have a n750 and I did the firmware update on the router and I have it check for firmware updates when I log in and i keep getting this message: "Cannot connect to the firmware information server,please double check the WAN connection." I have access to the internet.
How do I utilize the dual band feature on my belkin N750 DB? Do I have to set up two separate networks? Even then how when my devices PC, iPod, gaming devices are only recognizing the 2.4GHz band network?
I just bought a N750 DB router. On boot up, the 5Ghz side will show up for about 20-30 seconds and then it just "disappears". I was even able to connect to it @ 300mb with my laptop. The 2.4Ghz shows up just fine.
I have a Western Digital Mybooklive 3Tb hard drive connected to my N750 wireless router. It works fine, except that the new Media Server and the USB print and storage center says there are no USB devices plugged into it! Why is this?
I have an N750 DB router and it has been rebooting every few hours for no reason. This has just started happening about 4 days ago. I don't know why but when I check the system logs its filled with the following. [code]
Belkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.
Recently switched DSL providers and now have Cisco modem DPC3008. Able to connect to internet directly thru modem. Able to connect wired or wireless to router. Unable to get router to connect to internet via modem. Tried restart, reset, and new set-up. Called ISP (Charter) - no way, said contact Belkin.
I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
I have an issue with my N750 Wireless router, F9K1103. I have a Windows Home Server, HP Media Smart Server – EX470, that at times causes the router to lose connection, with the front panel light going from Blue (connected) to Orange (disconnected). When I pull the net cable from the server, after about 30 seconds the blue light comes back on.
I just bought a new Belkin N750 USB wireless adapter today to replace my old cisco USB adapter well I install the drivers and software that came with it and everything loaded correctly and showed that there was connections available.Where I live we don't have access to the routers as the are controlled by the rental agency and I can't get access to them. But anyways I can connect to the networks with my old usb adapter but not with the new one. My computer is Windows 7 64 bit.
I heard that the belkin n750 was good for gaming, but i cant seem to connect with 5ghz which i believe is alot faster than 2.5ghz, but yeah i would like to know how to configure my router to improve my game speed and performance.
I would like to upgrade my older router to a new one that I can connect my laser printer and storage via USB. I was looking at the Belkin N750, but it seems to get bad reviews. Is there another router that someone would recommend that has 2 USB ports (one for printer and one for storage)?