Belkin Routers :: N750 DB USB Printer Not Connecting?
Dec 20, 2012
N750 DB USB printer not connecting. I'm currently running a Canon MP480 multi-purpose printer connected through USB to the N750 DB router. I have both the printer driver and Belkin USB Print and Storage Manager software installed on a desktop PC that connects wirelessly to the router. The Belkin print manager software "sees" the printer, but when I try to connect it says please install printer drivers. I've installed and re-installed these drivers a few times, with no effects.
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
My N750 F1103 (f/w 1.10.16) LAN speed is limited to 5Mb why? I upgraded my Internet bandwidth to 20Mb+ tested and found it was only 5Mb, the cable company checked a few things and then I did some diagnostics and Isolated to the N750. I have two wired PC and same results with both PC's. This is supposed to have Giga bit LAN not Giggle bit LAN! I'm paying for something I cannot used to its full potential.
I have a N750 and I want to change the IP address through the browser. It is the standard 192.168.2.1 config. I change the IP to 192.168.15.x while hard wired and hit apply. The router reboots but still holds the same IP.
I cannot airprint. Contacted email support. Followed instructions to reset router. I did and I was able to print from my iPhone. ONCE. Then I installed my SSID and passwords and WIFI setup again and now I can't print. I have a brand-new airprint equipped HP 7520, an iPhone and 2 iPads.that I want to print from....the router is a N750 AV bought in July.
I have a belkin N750 DB router. I recently upgraded by internet service from 15Mbp to 30Mbp. If I connect my computer directly to the cable modem, I get 30Mbp throughput. However, if I connect the modem to the router my speed drops to 15Mbp. How do I get the router to support 30Mbp?
My ISP is Comcast and I own a Belkin N750 DBWireless N+ Router, I have a Synology NAS drive wired to the router. I am trying to set up the network configuration on the NAS drive so I can have internet access to the drive. My question is do I manually define the IP address, subnet mask, DNS, and gateway or do I select DHCP. If so what addresses should I use the address of the NAS drive form the router or the router address. I think I need to use the manual fields and use a static IP but do I get that IP address from the router or from my ISP (comcast)?
I have a n750 and I did the firmware update on the router and I have it check for firmware updates when I log in and i keep getting this message: "Cannot connect to the firmware information server,please double check the WAN connection." I have access to the internet.
How do I utilize the dual band feature on my belkin N750 DB? Do I have to set up two separate networks? Even then how when my devices PC, iPod, gaming devices are only recognizing the 2.4GHz band network?
I just bought a N750 DB router. On boot up, the 5Ghz side will show up for about 20-30 seconds and then it just "disappears". I was even able to connect to it @ 300mb with my laptop. The 2.4Ghz shows up just fine.
I have a Western Digital Mybooklive 3Tb hard drive connected to my N750 wireless router. It works fine, except that the new Media Server and the USB print and storage center says there are no USB devices plugged into it! Why is this?
I have an N750 DB router and it has been rebooting every few hours for no reason. This has just started happening about 4 days ago. I don't know why but when I check the system logs its filled with the following. [code]
Belkin N750 Router - wired connection can not access Internet. I've tried direct to modem and have no problem, have tried old router, no problem, but if I shut down desktop completely (Win7) and restart, I get no connection. Uninstalling the NIC (Intel 82579V Giga) and restarting, then I get connection again. However, if I start in safe mode with networking, I have no problems at all. I've disabled my firewall to no avail.
Recently switched DSL providers and now have Cisco modem DPC3008. Able to connect to internet directly thru modem. Able to connect wired or wireless to router. Unable to get router to connect to internet via modem. Tried restart, reset, and new set-up. Called ISP (Charter) - no way, said contact Belkin.
I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
I have an issue with my N750 Wireless router, F9K1103. I have a Windows Home Server, HP Media Smart Server – EX470, that at times causes the router to lose connection, with the front panel light going from Blue (connected) to Orange (disconnected). When I pull the net cable from the server, after about 30 seconds the blue light comes back on.
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router?
Uninstalled McAfee. Installed Frontier Secure, which uses the Windows Firewall. Received Windows Security Alert message that my Belkin USB Storage Center (where the printer is listed) was being blocked, and would I like to allow access. I selected "Allow Access". Printer has not been connecting all week. No error messages - it tries to connect, and then just stops. Can't find issues with the router or the printer - only with the firewall. Everything looks the way I assume it should - the printer is listed in the Belkin storage center. The Belkin storage center is listed in the firewall. There is no tech support for the firewall. There is no tech support for the printer.