Belkin Router Printer Not Connecting - Access Blocked?
Nov 2, 2012
Uninstalled McAfee. Installed Frontier Secure, which uses the Windows Firewall. Received Windows Security Alert message that my Belkin USB Storage Center (where the printer is listed) was being blocked, and would I like to allow access. I selected "Allow Access". Printer has not been connecting all week. No error messages - it tries to connect, and then just stops. Can't find issues with the router or the printer - only with the firewall. Everything looks the way I assume it should - the printer is listed in the Belkin storage center. The Belkin storage center is listed in the firewall. There is no tech support for the firewall. There is no tech support for the printer.
View 4 Replies
ADVERTISEMENT
Nov 26, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router?
View 2 Replies
View Related
Dec 20, 2012
N750 DB USB printer not connecting. I'm currently running a Canon MP480 multi-purpose printer connected through USB to the N750 DB router. I have both the printer driver and Belkin USB Print and Storage Manager software installed on a desktop PC that connects wirelessly to the router. The Belkin print manager software "sees" the printer, but when I try to connect it says please install printer drivers. I've installed and re-installed these drivers a few times, with no effects.
View 14 Replies
View Related
Nov 27, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 1 Replies
View Related
Dec 10, 2012
I have an iMac running 10.4.11. I would like be able to print through the router. I now have my PC laptops doing so. What voodoo do I have to do to make the iMac work with it?
View 3 Replies
View Related
Jun 26, 2012
I have a iP4820, Canon printer that has a USB port and a pictbridge port. It is currently connected to my desktop vis the USB port. Is there anyway I can connect the printer to the Belkin wireless router so that I can print from my laptops as well as my desktop?
View 1 Replies
View Related
May 15, 2011
I have recenly installed a RV082 with two ADSL modems connected to Broadband lines. Access to our networks is done via VPN accounts configured on Windows Vista laptops. The VPN network works fine and everyone has access to their network data and the Intranet/Internet.
I'm having problems with connecting a network printer to access over the VPN. We have managed to get a IBM1532 network printer working using the following network details by allowing the IP address of the printer through our VPN network/firewall.
We had to connect a Xerox C2424 workstation printer on site, so we configured the device using the same network details as the IBM printer, connected it to one of the available ports on one of the Broadband modems but we could not get the printer to be seen or connected to using this setup.
However I connect my own Home Laptop PC configured with the IP port settings above directly to the same modem as the Xerox printer this works but only after we changed the IP gateway address on the printer to match the modem.
If I switch on DHCP on the printer it finds the IP gateway address of the RV082 but will not allow us to send anything to it.As the ADSL lines are on a Dynamic IP rather than Static.
View 2 Replies
View Related
Dec 11, 2011
I'm setting up WHS 2011 for the first time. When attempting to set up Remote Web Access, WHS continues to recoginze my E4200 model information and router IP address but delivers the message 'Remote Web Access to Your Server is Blocked'. Cisco and MS say the router is compatible with WHS and that it should set up through the wizard but no luck following many attempts, including manual set up of DHCP Reservation and Single Port Forwarding on ports 80/443 (not sure I did this correctly).
I've taken the router back to default settings with the exception of enabling Remote Management under the Remote Management Access section of the Administration menu tab; tried again with the same result. What settings to change to make this work?
View 7 Replies
View Related
Nov 26, 2012
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 3 Replies
View Related
Sep 27, 2011
I have a new n series Belnet wireless router that can take a usb printer. I have a Lexmark 2200 Series 1 Printer (with usb connection). I have used this printer with my laptop (runs Windows xp) by connecting the printer usb directly. I have also connected my laptop to the wireless router. I have plugged the printer into the wireless router's usb port. Is it possible to access the printer this way? I do not know what I should do next. The laptop cannot access the printer through the wireless.
View 5 Replies
View Related
Aug 16, 2011
I have a Dell desktop and a dell laptop. I got a new belkin n300 F9K1002v1 Router today and now I can't print to my dell 968 aio printer from my laptop. the printer is connected to the desktop with a usb cord and was working with the old router?this info is from my laptop:
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 2, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5550 @ 1.83GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3061 Mb
Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 448 Mb
Hard Drives: C: Total - 225874 MB, Free - 126104 MB; D: Total - 9999 MB, Free - 5832 MB;
Motherboard: Dell Inc., 0U990C, , .DHF4PF1.CN7016686601RZ.
Antivirus: Lavasoft Ad-Watch Live! Anti-Virus, Updated and Enabled
View 5 Replies
View Related
Feb 5, 2013
have a home Sony VAIO Computer running XP Media Center Edition, Belkin Wireless N Router, HP B209 Wireless printer, 1 year old Lenovo laptop, and an iPhone 4s.I can't make them all play together.I noticed yesterday that my iPhone hadn't been connecting to the WiFi for several days, so I tried to see what might be going on. I tried to force pair the iPhone by turning off Data Connection, which usually forces the WiFi, which it did, but then when I went to a webpage it wouldn't load even though wifi was showing full signals.I then booted up my lenovo laptop, and it connected to the internet and worked like a charm. Then my iPhone4s started working again. Why not now finally set up the wireless aspects of my HP B209 that I've never used, so I can print from my laptop wirelessly, which I've always wanted to do.So I was able to setup the printer after adding the MAC address of the printer to my belkin router by going to the IP address for the router and adding that specific address, I changed NOTHING ELSE.Internet on laptop not working now. It shows my wireless network with full bars in range, but when I go to connect it simply says it cannot connect, right away. I check my phone, wireless GONE again! I tried to force pair the phone, no dice. I "forget the network" on my phone, it still shows available, I connect put in my password and it immediately denies me, I tried un-plugging the router, restarting all computers, un-plugging router -and- restaring all computers, turning off the printer, repeating all previous steps, and finally I went and deleted the MAC address I added to the router, and all of the above did nothing to fix the solution.
View 4 Replies
View Related
Jun 3, 2011
How to connect a Brother wireless printer to the Belkin Surf N300 wireless router? i tried a few times and it wont connect.
View 1 Replies
View Related
Jan 4, 2011
Have a non-wireless printer (HP F4280) and non-wireless Desktop (Dell Dimension 2000). Just added an HP G62 wireless laptop and Cisco Valet+ router. My problem is I want to make the printer wireless but their is only one USB port and no ethernet port. If I put an adaptor into the USB port on the printer to make it wireless, I will of course loose access from my dektop. Can I put a splitter into the printers USB port and use an wireless adaptor plus the cable to the desktop?
View 5 Replies
View Related
Jun 21, 2011
I had been using my printer through my linksys router with no problem until I added a password to the linksys. Now I can't print. My computer says it can't "ping" the printer.
View 1 Replies
View Related
Apr 1, 2012
I managed to connect my USB printer (and tested ok) through the E3200 router using the Cisco Connect programme on Windows 7. I note that there was an option for a USB Printer connection in the set-up screen.
When I tried it on the Mac using Mac OSX 10.7.3 and Cisco Connect Ver 1.4, I noted that there was no option for a USB Printer connection.
View 3 Replies
View Related
Apr 11, 2011
I think I have worked out that you can`t currently connect a usb printer to the usb port on the e4200 in order to share it over the network.
However I have heard reports that this might facility might be enabled in the spring.
I have also heard something about `virtual usb` but I don`t know whether this has anything to do with it.
View 9 Replies
View Related
Jul 26, 2012
Just purchased an E900 wireless router and cannot figure out how to connect my Samsung wireless printer. The printer has a WPS button, but the router does not. The router wants me to input information into the Samsung printer, but the printer has no screen, and I cannot find a place to input the router info anywhere in the Samsung software. I am going crazy here...I'm not a techie, but I'm also not a complete technology idiot.
View 2 Replies
View Related
Mar 3, 2013
I was wondering if there was a way to connect a wired printer to my linksys E3000? or am I still stuck with using my spare desktop.
View 4 Replies
View Related
Nov 26, 2011
I have a BEFW11SF V4 firmware version 1.52.03. I just bought an HP DJ3051A and can't get it to connect. HP support says I need to change a setting to mixed mode but I don't see that I can. Does this router supports mixed mode and if so how do I change it?The other comment the HP rep made was the printer does not support Wireless N. I am fine with this since the router says Wireless B. It seems based on the HP rep's comment that as long as I am not using Wireless N, then I should be fine.
View 1 Replies
View Related
Sep 1, 2012
I have recently bought a Belkin N300 Wireless N Modem-Router and am unable to connect it to the internet. My laptop registers the router but the router won't connect to the internet. The router also is blinking a red light.
View 2 Replies
View Related
Dec 6, 2011
I have a desktop computer connected to a modem and a wireless Belkin router. I bought a Belkin Surf&Share wireless USB adapter so that I could move the desktop elsewhere in the house and still connect to the internet. When I disconnect the computer from the router, the wireless light on the router turns red and I can't connect.
View 1 Replies
View Related
Nov 10, 2012
The other day my wifi was working the all of a sudden today my wifi stopped and said it's disconnected. On the router the only non-green light says "LINK"and it keeps flashing orange. How do i fix this because i cannot tweet pics from my phone without this working...
View 1 Replies
View Related
Aug 31, 2011
I am having trouble connecting router to my pc hp pavillion with windows vista using verizon internet.
View 1 Replies
View Related
Sep 2, 2011
Where do I find View Available Wireless Networks in Windows 7?In XP there is a network icon in system tray to right click but what about Windows 7?
View 2 Replies
View Related
May 13, 2012
I would rather have wireless to wireless . Like I said I have a new EA4500 trying to extended my wireless connection to my back yard still having the same trouble of small to no signal, I have a Belkin N+ Ver.2 that I had been using with the same trouble. I would like to connect the belkin N+ to the EA4500 to extend my wi-fi to my back yard and back half of my house.
View 7 Replies
View Related
Mar 12, 2013
I have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC. I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (172.168.1.149), Subnet Mask (255.255.255.0), Default Gateway (172.168.1.1) and 3 DNS addresses (172.168.1.1) (10.30.0.1) (8.8.8.8) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 172.168.1.148
I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router?
View 3 Replies
View Related
Aug 26, 2012
I've got a Belkin F5D8236-4 wireless router. I've had no trouble connecting three laptops to it, but I've completely failed with my HTC smartphone and a friend has failed with a iPhone, I've also failed with an iPod. I've just got a Nexus 7, for my birthday, and that won't connect either! All devices find the network, they just don't connect!
View 6 Replies
View Related
Jan 1, 2011
I have a Linksys wireless-G connected to my main computer and modem. We live in an extremely long house and I am attempting to connect a Belkin wireless-G router so that the signal is stronger on the other side of the house.
View 1 Replies
View Related
May 11, 2011
My internet provider have blocked a website. I know there is a way to bypass the block and go to the website, without using websites such as Hide My ***! Free Proxy and Privacy Tools - Surf The Web Anonymously.
View 1 Replies
View Related
Mar 28, 2013
I have a brother who frequently blocks my internet access, and he does it while maintaining his own connection so he's not unplugging the router or anything. He also blocks it from his own computer, meaning he doesn't take out my wireless card or anything like that. I was wondering how to counter this and get my internet back whenever he blocks it, or prevent it.
View 1 Replies
View Related
Oct 21, 2011
I recently purchased a new Belkin N wireless router, model number (F5D8236-4 V3), i am however trying to connect this router to my old Belkin G wireless Modem Router (F5D7632-4 Ver7000uk).Now i can't seem to get the N router to connect to the internet-after much faffing about i can get all the LED lights to turn blue-bar the wireless which blinks amber (i did this by turning the DHCP server off, and by using the same WEP code). I get limited connectivity wirelessly and wired, which basically might aswell just say no connection.
Taking the N router out of the equation, the g router can connect to the internet wired (it no longer seems to work wirelessly, and had a horrible range on it anyway). I use a PPPoE connection-all my ISP details are correct.how i can get the N Router to work wirelessly and wired.
View 6 Replies
View Related
Jan 27, 2012
I would like to know how you can unblock the blocked port to access website on LAN
View 1 Replies
View Related
