I have recently bought a Belkin N300 Wireless N Modem-Router and am unable to connect it to the internet. My laptop registers the router but the router won't connect to the internet. The router also is blinking a red light.
View 2 RepliesI am connecting to internet via motorola modem which gives me approx 6 Mbps download speed when I test it with both speedtest.net and speakeasy.net. Any device that I use connected wirelessly to my Belkin N300 router only acheives about 1.3 MBps of download speed. Is this just the way it is or could I have a router configuration issue or something else?
View 2 Replies View RelatedI have a belkin surf n300 usb wireless N micro adapter. No problems installing this adapter on a HP Desktop running windows 7. I have tried to install on a gateway laptop also running windows y 64 bit. In device manager it show that the product is working. It will not connect to any network. The adapter is an F7D2102 az ver. 2011az
View 2 Replies View RelatedI recently bough a belkin router (Share N300) but it just wont connect to the internet.My setup is as follows:ADSL -> Modem -> Router -> PCThe internet works fine when I connect it directly to my PC (via the modem), and other PCs too.So no issue of MAC address lockdown.I've tried connecting through static mode with the data from ipconfig /all, but it still doesn't work.I've even installed DD WRT and Tomato to no avail.
View 2 Replies View Relatedi m using belking sufr n300 but i m not able to access internet. if i connect brodband cable directly to computer then i am able to browse.
View 1 Replies View RelatedI am trying to connect a Seagate Backup Plus 4TB USB HDD to the USB port on my Belkin ShareMax N300 wireless router. The router does not recognize this HDD. I know that the HDD is functioning because it works when I connect it directly to my laptop USB. I also know the Belkin USB port is working because it recognizes a 4GB USB memory stick and a 320GB Toshiba USB HDD. Is there a fundamental compatability problem, or is there some configuration that must be performed (e.g., reformat from NTFS to FAT32, etc.)? I saw some message traffic on the Belkin support site that indicated some issues with earlier versions of Belkin routers using larger HDDs (e.g., 4 TB). My router has a serial number 121026G3101468, model number F7D7301 v1.
View 3 Replies View RelatedThe main router is Belkin N300 and the new one is D-Link N300 DIR-651 for extended range.
View 1 Replies View RelatedCan't get internet.I can plug laptop directly into modem and works fine. When I plug modem into brand new wireless router (N300) the light glows amber. I've been through the set-up 10 times. Actually the same reason I replaced old router with this one.
View 2 Replies View RelatedI have a belkin n300 and it whilst the modem itself is showing a static blue light, its coming up as an explanation mark on the wifi symbol on my macbook. This has been happening since yesterday when I was fiddling around with the settings on the IP address (192.168.2.1) to get the printer to work wirelessly which it did once then the wifi network went down.
View 1 Replies View RelatedI have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View RelatedBelkin N300 - bought two weeks ago and have had very slow internet connection since.
View 1 Replies View RelatedMy N300 Wifi Range Extender does not let me connect to Internet. I can access other systems connected on the main WIfi network, but I cannot access Internet.I observe as well that all systems connected to the Extender appear, from the main Wifi network, having the same Mac address. I believe that my ISP (Telenet) does not accept that, and that this is the reason I cannot connect to Internet. Is there any way to change that behaviour ?
View 9 Replies View RelatedI recently got an older dell laptop that doesnt have automatic availability to wifi i had purchased a netgear n300 usb internet thing and it still will not connect to my home wifi how do i fix this?
View 1 Replies View RelatedI have an N300 router, and I'm having some connection issues. At least once a day I randomly lose connection. This is frustrating because I like to watch videos online and play games online, and randomly disconnecting right in the middle of a game with other people is not fun.
View 0 Replies View Related#1: I have an N300 router and all of my devices (two laptops, one PS3, and one 3DS) connect to the internet just fine. But I'm having a problem when trying to connect to a friend on my 3DS when playing Pokemon Black Version 2. I've never had this problem before I got my N300 router. The 3DS connects to the internet without issue to download updates and shop the Nintendo store, but this in-game connection is not working.
#2: When I started using that same N300 router, suddenly my access to www.omegle.com was severely limited. It's a video chat site on which now I can no longer see the other users' video. Rarely a video will come through, by 90% of the time I just get black screens which I know I shouldn't be getting.
My SURF N300 router makes my internet signal very weak, 1/10 of what was contracted but it works perfectly with the cable connected directly to the computer, how can I configure it to work properly?
View 1 Replies View RelatedI have and and android tablet I just bought and I can't connect to the internet with my Belkin N300 Router all my computers and smartphone work very good to this router and the phone works with wifi here also. I can't get this tablet to connect to the server I have put in all the ssid and the name of the server. When I try to connect it says connecting, then autherizing and then it does a loop and does not ever change,keeps on doing it. In the little shell that is to change color when connected there is a very small lock showing and I am not sure just what todo about this.
View 3 Replies View RelatedI am experiencing a great inconvenience with my relatively new Belkin Surf+ N300 wireless ADSL router.I am confident that the router has been doing this since I got it, however I have not noticed until now. Whenever I try to access a URL with the word "router" anywhere in it (e.g url...) it will take me to my router's settings page (usually comes up when the router's LAN IP is entered)Yes this is very handy if you don't know the LAN IP, or are less skilled in router management, however if, like in my case, you like to access websites with "router" in their URL, you have a serious problem. I have tried factory resets, and have scoured through the settings of the router but have been so far unsuccessful.
View 4 Replies View RelatedI have a belkin n300 wireless router that i know works because the ps3 connects to it but when i tried to add my desktop to the wireless router i used the installation cd to download onto the computer (which i was then told by belkin tech support that the cd was only for extra stuff like printers..) when i installed the cd it said not reccommended to install because it wasnt windows xp authorized but i did this any ways.. i have also been looking online for diferent things to do to try and get my computer to connect to the router so i have changed things on the computer that i have no idea how to backtrack and take it all back..i tried rrstoring my system to an earlier date and it wont do it. now my computer wont even pick up on a wireless connection.. i then tried to connect directly to the modem (comcast box) and i still couldnt get on internet!
View 3 Replies View Relatedi have a belkin n300 wireless router and a embarq 660 modem. i wanted to change the password, i don't like the default password. it's too easy to get hacked. anyway, i tried typing the ip address in the address bar of a browser, and it came up a login page, so i created a new login. and then it opens up a page call ZYXEL total internet access solution. it has a lot of setting and button about the network but i couldn't find a button that can change the wireless router's password.
View 3 Replies View RelatedI have a Belkin Surf N300 wireless Modem-Router, but cannot get it to connect to my Android phone. I can connect it to my Nexus tablet, to my desk-top and my lap-top, so I know there is nothing wrong with the router itself. Every time I try to connect the phone, it locates the network, scans, authenticates, but then says "Disabled" and the message: "Secured with WPA/WPA2 PSK" with "locked network" symbol. What does this mean? This is on the label that came with the router: "Security Type WPA/WPA2" but I don't know what to do in order to remove the lock. The phone is a Vodafone Smart Chat and I bought it specifically to be able to connect to Wi-Fi networks.
View 1 Replies View RelatedI have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC. I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (172.168.1.149), Subnet Mask (255.255.255.0), Default Gateway (172.168.1.1) and 3 DNS addresses (172.168.1.1) (10.30.0.1) (8.8.8.8) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 172.168.1.148
I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router?
I have a Embarq 660 Series modem, but i wanted wifi. so i bought a belkin N300 wireless router this morning. And it won't connect to internet. I'm sure i've plug the cable in the right spot. And the EQ 660R ADSL router/modem is working. The belkin package came with a CD, and it's the setup program for the wireless router. but as it tried to form a connection, it said failed to connect to the modem. so does this means embarq 660 series isn't compatible with Belkin N300?
View 3 Replies View RelatedI have a Belkin N300 router. When a computer is hard-wired to the router, I get about 26Mbps, but all of the wireless devices in my house are limited to about 56kbps. I tried logging into the router to see if there was something "choking" the connection speed, but nothing really jumped out at me. Is there a setting of some kind that could be causing this?
I do have a signal repeater since my house is so big, but there is nothing within those controls that would seem to have that kind of effect either.
my netgear wireless router cannot see my n300 usb adapter. it shows as working in my device manager, but the netgear router says wireless not connected. when installing the adapter it said that windows has an icon to the left of the taskbar that i can click on and ask to join a network, which it didnt. it just showed network and an option to open network and sharing center, which i did. there were no wireless networks that showed available for me to log into with the adapter
View 4 Replies View RelatedWe just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies View RelatedI have a Dell desktop and a dell laptop. I got a new belkin n300 F9K1002v1 Router today and now I can't print to my dell 968 aio printer from my laptop. the printer is connected to the desktop with a usb cord and was working with the old router?this info is from my laptop:
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 2, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5550 @ 1.83GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3061 Mb
Graphics Card: Mobile Intel(R) 965 Express Chipset Family, 448 Mb
Hard Drives: C: Total - 225874 MB, Free - 126104 MB; D: Total - 9999 MB, Free - 5832 MB;
Motherboard: Dell Inc., 0U990C, , .DHF4PF1.CN7016686601RZ.
Antivirus: Lavasoft Ad-Watch Live! Anti-Virus, Updated and Enabled
How to connect a Brother wireless printer to the Belkin Surf N300 wireless router? i tried a few times and it wont connect.
View 1 Replies View RelatedHow do you connect two routers together to increase signal through the whole house? I am trying to use the n300 as my main router (its hooked to cable modem) and use the 2wire as an access point.The two are connected by a known good ethernet cable.
View 2 Replies View RelatedI have Netgear N300 (DGN3500) Wireless Gigabit ADSL2+ Modem router.The Router has a phone socket (that is RJ 11 socket) to connect to the Internet. But in my home I have Ethernet socket on the wall. That means the Internet is coming through Ethernet cable. How to connect my ADSL2 Modem router (with the phone socket) to the Ethernet? I bought a ISDN-DSL (8p4c-6p4c) connecting cable and it is not working when the router and Ethernet are connected..I tested my router at one of my friend's place where ADSL connection is available and it was working when directly connected to ADSL line. Unfortunately at my home I don't have ADSL but Ethernet connection.
View 13 Replies View Relatedi lost the admin security password of my N300 Share modem-router. How can i return to the factory settings ?
View 1 Replies View RelatedWhy I cannot find "Wireless Bridging" under "Wireless" of my belkin n300. Its model is F9k1002v1.
View 2 Replies View RelatedThis morning I lost wifi connectivity. I reset the router and powered off and on the modem along with the router but to no avail. The blue stripe no longer shows on the top corner of the machine.I am able to connect to the internet using the ethernet ports on the router. I also tried to get into programming using 192.168.2.1 but it is timing out.
View 1 Replies View Related