Cisco Routers :: RV082 Access Resources On RV016
Apr 29, 2013
I know this *should* be simple but having a devil of a time getting it to work.
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10
[Code].....
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.
View 3 Replies
ADVERTISEMENT
Jun 1, 2011
VPN tunnel backup is not available on the RV016 firmware version 4.0.2.08 (it IS on the RV082. The data sheet and the manual for the RV016 is wrong. I have purchased several RV016 hardware V3 and several RV082 hardware V3. Both have the same current firmware version. We have noted that the RV016 does not have the VPN tunnel failover option found in the RV082. It also does not have split DNS (noted in the manual. A I would have thought that the firmware would provide equal options on the RV042, RV082, and RV016.
View 2 Replies
View Related
May 16, 2012
I'd like to setup a WCCP in those routers, but as I read, it's not possible.
Another way to circumvent this limitation is to foward a request to the router from the LAN port 80 to a LAN IP, something like:
LAN 1 192.168.1.100:80 -> router -> LAN 2 192.168.1.101:80
View 1 Replies
View Related
Mar 9, 2012
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
View 2 Replies
View Related
Apr 24, 2012
I am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.
View 1 Replies
View Related
Oct 12, 2011
I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
View 4 Replies
View Related
Aug 24, 2011
I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies
View Related
Apr 19, 2012
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
View 2 Replies
View Related
Nov 15, 2010
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
View 6 Replies
View Related
Jun 2, 2011
Currently I have a VPN tunnel setup between our company locations. Location A has Linksys RV016 and Location B has RV082. Everything has been working with no problems for the past 2 years with only minor disconnect issues in the VPN tunnel between the locations.
For the past 2 weeks I have been running into issues with the Tunnel. Users in Location B are reporting problems with losing connection to applications that are hosted in Location A. At first I start with doing a ping to router address in Location B and I get "request timed out". Next I login to router in Location A and under VPN I notice that the VPN tunnel is not disconnect (I see disconnect button). Once I click on Disconnect the screen refreshes and that seemed to restablish connecting with router in Location B. The drop connection has been been going on for the past 2 weeks and only happens once a day specifically between 1 PM and 3 PM EST. I have been reading all over the internet and no luck at all. The VPN tunnel settings are the same on both routers and under Advanced options both Keep Alive and Dead Peer Detection (DPD) are checked.
View 1 Replies
View Related
Oct 25, 2011
used to be able to access this secure website [URL] prior to a firmware upgrade. Can no longer access. On Firmware Version: 3.0.2.01-tm. Assuming there's some default setting in the firewall?
View 2 Replies
View Related
Feb 16, 2012
We have had our router and remote computers set up with Quick VPN for over a year. We've had our share of problems but have worked around them.
Now, out of the blue, no one can connect to the VPN. I went in to try to do some 'troubleshooting' and the ONLY thing that allows our VPN connection to go through is to completely disable the RV016 firewall. We have too many remote users to actually start and stop the firewall everytime someone needs the VPN connection.
View 1 Replies
View Related
Nov 4, 2011
We are having several issues with the new batch of RV016 (rebranded as cisco and with cisco firmware. The Cisco RV016’s are configured to load balance aDSL internet access from 4 Cisco 877 modems/routers. Ports used are WAN1, WAN2, WAN3, WAN4.
Issues are: WAN 1 port resets to 0.0.0.0 regularly and traffic on WAN 1 fails DNS fails regularly behind the RV016 onlyIntermittent internet connection behind the RV016Slow internet connection behind the RV016Extremely slow DNS query and reply behind the RV016 (DNS resolve takes 1min -1m30)
The issues above are reported from different deployment sites and with different scenarios.
We also test above with Code...
View 1 Replies
View Related
Jun 27, 2012
We have an RV016 (hardware version 2, firmware version 3.0.2.01) behind a cable modem. Attached to this RV016 is a switch to which our other devices are connected. Among those is another switch, a wireless access point and our VOIP phone system.
The issue with this setup seems to be as follows:
The Mac machines at our office seem to be unable to get internet access reliably. What we have observed is that a connection to the wireless access point is made. Google will load fine, then when performing a search it comes back with either a dns lookup error or just says that the site can't be found. Sometimes sites will load just fine, sometimes they don't. Our Windows or Ubuntu machines in our office hardly ever have that issue, but they do on occasion. Essentially internet is usable on Windows and Ubuntu, but not on a newer Mac. Mainly three Macs are affected that run a newer OS. Two other Macs (older OS) seem to be fine. My coworkers (who have that issue at work) report that at home they do not.
The DNS servers on the router were set to our ISPs addresses. I have since changed them to opendns servers. The issue persists.
When connecting a MacBook directly to the cable modem, everything works fine. Since we are using NAT, I do need to use the router. There are devices attached to it that these users need to be able to get to.
View 10 Replies
View Related
Jul 4, 2012
My company is using an RV016 router as a gateway to our internal network. My end goal is to allow remote users to access network shares via Samba.I've been trying to create a VPN using the router with absolutely no luck. I've tried QuickVPN. I've tried creating a client-to-site group vpn. I've tried creating a client-to-site tunnel vpn. I've tried pptp. Nothing will allow me to establish a VPN connection. Sometimes there is information logged in the router but most of the time there is not.
View 1 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Oct 23, 2012
I have a customer that has a Cisco 2900 Series ISR on his Headquarters, and has some branches with RV082s.We have VPN Client configured on the 2900 ISR Router and we can connect remotely using the VPN Client to the Headquarters (192.168.1.0) however we can't reach the branches subnets (192.168.2.0, 192.168.3.0, etc.)... we found out that in the RV082 you need to specify the secure traffic as a destination, but in only supports one network (192.168.1.0 or Headquarters in this case), we can't specify the VPN Client pool defined on the ISR so it can reach the incoming VPN Clients.Is there any way to accomplish this? We need to access the branches subnets when connecting using VPN to the 2900 ISR.
View 1 Replies
View Related
Mar 22, 2012
I have found numerous posts discussing this but have yet to find a solution. I have an RV082 with firmware 2.0.0. 2.0.0.19-tm and I need a way to limit the incoming smtp traffic to just the spam filtering company.I have a port forwarding rule to forward WAN1 port 25 traffic to 192.168.1.10.I tried to add an access rule to deny all port 25 and then added one to allow WAN1 port 25 source <spam company> destination 192.168.1.10The RV082 log screen shows the traffic allowed but it does not work. If I uncheck the 'enable' box on the DENY port 25 rule email is still blocked. Only when I uncheck the 'enable' box on the ALLOW rule does email start flowing again.
View 10 Replies
View Related
May 9, 2012
I am deploying a small wireless LAN (192.168.1.xxx) at a remote site and would like to access a PC at LAN IP address 192.168.1.2 across the Internet via TeamViewer so as to monitor devices on that LAN. The wireless LAN uses about 12 Cisco Aironet 1310 bridges in a ROOT-NONROOT (I guess this is point-to-multipoint?) configuration.Our ISP has given us a single static WAN IP address, subnet mask, gateway, and two DNS server addresses.
My intent was to assign our static WAN IP address from the ISP to our RV082 router, plug the LAN devices (including the PC at 1.2) into the RV082, and then use Network Address Translation (NAT) to forward TeamViewer traffic to the PC at 1.2. But the RV082's user manual says NOT to use the router's WAN IP address in the NAT table.So I'm confused as to how to send remote TeamViewer traffic to the PC inside my LAN. Is NAT not the way to do this? Should I be using port forwarding instead?I guess another way of skinning this cat would be to put a second NIC in the PC and let the second NIC have the WAN IP address so that it would be the first point of contact from outside, but that defeats some of my purposes for having the RV082 in the first place.
View 1 Replies
View Related
Jul 25, 2011
I have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies
View Related
Oct 9, 2012
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies
View Related
Apr 23, 2012
I can connect via VPN with the QVPN but once I am connected to my network I cannot view the resources available to me by LAN. I am nowhere near aware as to why.
View 4 Replies
View Related
Oct 5, 2010
I have a Cisco 881 and I want to use Easy VPN.
-VLAN 1: 192.168.4.0
-WAN: 10.0.0.0
-VPN: 192.168.8.0
VPN connects and I get an IP of 192.168.8.100 from my pool. I can ping my cisco at VLAN1 (192.168.4.1), but I cannot access my local resources. I guess I miss a NAT configuration.
View 11 Replies
View Related
Jun 12, 2011
The Linksys is connected to a cable modem and a Dell Vostro system, the Netgear is connected via Cat 5 to the Linksys and the Linksys is the DHCP provider to the Netgear.The Vostro shares hard drives, folders and printers to the networkBoth have wireless and wired users.They are each DHCP providers to their users.How must I configure each to provide users on both routers access to all network resources
View 2 Replies
View Related
Feb 9, 2011
I've set up a VPN using a fortigate 50b wifi and forticlient ipsec VPN. when I log into my office from home, I cant see anything on my network at all. I can however remote desktop into other PC's and can access stuff that way. I was under the assumption that ... one a VPN connection is made in the LAN you should be able to see other pcs and servers in the workgroup. Is this not the case or do i need to configure something?
View 2 Replies
View Related
Aug 19, 2011
I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies
View Related
May 24, 2011
I have 3 networks coming from the DMZ (VPN) and only one works:10.132.24.0/24 Not working10.132.25.0/24 Not working10.132.26.0/24 Working The thing is, the one that works is on the same network as the DMZ(VPN) interface. The other two do authenticate and they get an IP from the VPN Pool. but they just cant access anything.
View 11 Replies
View Related
Nov 26, 2012
I'm working on setting up a couple of new WAN sites with 256K frame relay circuits back to our main building. Each new site has a new PVC, and both are pointing back to a PVC on a T1 at the main building. The main site has a 2801 with a single CSU/DSU WIC, and each new site has a 1841 with a 3560 connected to fa0/1. At both sites, I'm able to get the circuit up, and the serial interfaces at both new sites show up/up, and the subinterfaces at the main site also show up/up for both sites. Routing is being done by EIGRP, and both sites are able to establish the 2801 as an EIGRP neighbor, and I'm able to ping/tracert anywhere on our network by name or IP, so routing and DNS appear to be working. I can also ping both new routers from the main site. However, that's about all I can do. I'm not able to access any resources on our network (email/shares/internet/intranet/etc) from the two new sites. I can ping the new routers/switches from the main site, but can't ssh to them. I can ssh to them locally. There are no firewalls in the equation, and I don't think there are any ACL's in the picture either.
Can ping and tracert just fine anywhere on our network (from both the 1841, a PC plugged into the 3560, or a PC plugged directly into the fa0/1 port on the 1841), including out to the internet, by name or ip.Can ssh to local router, but not to anything that isn't localDNS is workingDHCP not working using ip helper pointing to DHCP scope on server at main site, have to use static IPCan't rdp to anythingCan't get emailCan't browse windows sharesCan't get to any websites, external or intranet. IE says "Website found, waiting for reply..." but eventually times out.
I did some testing for communication over certain port numbers using telnet and nmap, and found the following:
Can telnet to url.. and local intranet webserver on port 80 (http)Can telnet to two of our Exchange Servers on port 25 (SMTP)If I run an nmap scan on url...com, or our intranet webserver, it confirms that 80 and 443 are open, but the pages will not load. I am able to telnet (port 23) to a state mainframe via the internet that some of our employees use, and I do get the expected login screen. I tried erasing the config one of the new routers, and just added back the bare minimum config to get the circuits up (serial/ethernet interface configs, eigrp), but saw the same symptoms.
One other thing to note: the 2801 at the main site has three other frame relay sites connected to it on the same WIC as the new sites, all of which are working fine.
I just don't understand why I can ping everywhere I need to be able to ping, and port scans show that communication is open over needed ports, but the applications don't work.
View 1 Replies
View Related
Feb 24, 2011
I am having an issue with my Cisco VPN Client. I am new to VPN setup, so this is probably something easy I am missing. I have a 2611XM router acting as my internet gateway for my local lan, and my VPN Server. I am doing all my testing from a company laptop with a mobile broadband card. The VPN will connect, but anytime I ping anything within the inside network, it comes back with the public IP of the outside interface. I have NAT overload configured so everything on the inside network can access the internet, which it looks like might be causing my problem.
When i remove the nat overload on my fa0/1 interface, the vpn will connect to any resource on the inside.
View 9 Replies
View Related
Jan 24, 2012
I have two places that I work out of. One is in Romania and one in Bulgaria. In Romania, I have a small office/home network set up. It has at least 8 computers (including the three that I have with me currently - some wireless and some towers) and a couple of android phones and Ipods. I have no trouble accessing any of the computers shared folders or them accessing mine. There are a varity of operating systems used there from XP, Windows 7 and Mac.Everything works great. All the computers can access each other shared resources. All the computers are set to get IP automatically from my DLink DIR - 600 router. I have brought my three computers to Bulgaria (tower and two laptops). They are all set the same- no changes in settings. However, in Bulgaria, All three computers CAN access the internet but NOT each other.
[code]...
View 14 Replies
View Related
Jun 9, 2013
2504 contrller with 1042N ap's. NPS and group policy (for computers) is setup. Certificates are setup.Logging on as a domain user I can connect to the wireless network but am only getting Internet access. I can not access any domain resources.DHCP is handled by a domain controller. I can ping servers and printers, but cannot access them. Can't map a drive, add a printer or access services on the network.
View 1 Replies
View Related
Sep 6, 2012
I want to use Cisco VPN Client to VPN to my SA520 to manage a UC320W. I can establish a VPN connection to the SA and ping both the SA and a switch that I have on the network, but I cannot ping my UC. I've set up firewall rules to allow ANY-ANY access from LAN-WAN, and a WAN-LAN rule to allow a certain range of IP addresses (the IP addresses assigned from the VPN DHCP pool, in this case, 192.168.12.x) access to the UC.
My SA IP address is 192.168.75.1 and my UC is 192.168.75.2 (I can ping both when I am directly connected to a LAN port on either equipment).
View 1 Replies
View Related
Nov 7, 2012
Since we upgraded our ASA from 8.3 to 8.4(4), VPN users cannot access resources. This worked fine until the appliances were upgraded. We get the message:
[code]....
View 2 Replies
View Related
