Cisco Routers :: Setting Up RV082 For Team Viewer Access To LAN
May 9, 2012
I am deploying a small wireless LAN (192.168.1.xxx) at a remote site and would like to access a PC at LAN IP address 192.168.1.2 across the Internet via TeamViewer so as to monitor devices on that LAN. The wireless LAN uses about 12 Cisco Aironet 1310 bridges in a ROOT-NONROOT (I guess this is point-to-multipoint?) configuration.Our ISP has given us a single static WAN IP address, subnet mask, gateway, and two DNS server addresses.
My intent was to assign our static WAN IP address from the ISP to our RV082 router, plug the LAN devices (including the PC at 1.2) into the RV082, and then use Network Address Translation (NAT) to forward TeamViewer traffic to the PC at 1.2. But the RV082's user manual says NOT to use the router's WAN IP address in the NAT table.So I'm confused as to how to send remote TeamViewer traffic to the PC inside my LAN. Is NAT not the way to do this? Should I be using port forwarding instead?I guess another way of skinning this cat would be to put a second NIC in the PC and let the second NIC have the WAN IP address so that it would be the first point of contact from outside, but that defeats some of my purposes for having the RV082 in the first place.
View 1 Replies
ADVERTISEMENT
Jun 1, 2013
I have a ASA5505 and I'm having trouble to achieve the following setup, block any kind of connection from outside except for IIS on port 80 and 443 but allow from the server to access any outside address, by domain or ip. Right now apps writen in C# on the server are throughing socket errors and Teamviewer remote control is not working, I would like it to replace remote desktop.
View 3 Replies
View Related
Jan 3, 2012
I want to block team viewer using cisco ASA-5585 asdm..
How to block it using regular expression
View 1 Replies
View Related
Jun 10, 2013
We are setting up a vpn between a cisco RV082 and a checkpoint device. From the Cisco device we have set up (as remote IP) the public IP 85.xxx.xxx.xxx but when we try to start the tunnel the VPN log (from RV082) report the error "INVALID_ID_INFORMATION" as described below.
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: sending encrypted notification INVALID_ID_INFORMATION to 85.xxx.xxx.xxx:500
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: we require peer to have ID '85.xxx.xxx.xxx', but peer declares '10.yy.yy.yyy'
[code]....
The IP 10.yy.yy.yyy. reported in the log is the natted ip of the Checkpoint device.
View 3 Replies
View Related
Jan 13, 2011
I have a new (linksys/cisco) RV082 Router that I have just set up and everything is working except that I can't configure it to allow public access to our web server. I have tried configuring port forwarding under the Forwarding and UPnP menus and still no access from the outside. I have tried accessing it from the outside using both the URL and the IP address and still no access. I have checked with my ISP and no ports are being blocked from their end. I can ping my public static IP from the outside with no problem. The documentation that I've found for this router refers to a menu that is different from the menu of this router and refers to an Applications & Gaming menu which isn't there, but it seems like the port forwarding should handle this.
I have a static public IP, a static internal IP for the server. I have set the port forwarding and UpNP to point to the IP of the server using port 80 and a secondary forward to port 8080. There are no issues accessing the website from within the LAN.
View 2 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Apr 29, 2013
I know this *should* be simple but having a devil of a time getting it to work.
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10
[Code].....
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.
View 3 Replies
View Related
Oct 23, 2012
I have a customer that has a Cisco 2900 Series ISR on his Headquarters, and has some branches with RV082s.We have VPN Client configured on the 2900 ISR Router and we can connect remotely using the VPN Client to the Headquarters (192.168.1.0) however we can't reach the branches subnets (192.168.2.0, 192.168.3.0, etc.)... we found out that in the RV082 you need to specify the secure traffic as a destination, but in only supports one network (192.168.1.0 or Headquarters in this case), we can't specify the VPN Client pool defined on the ISR so it can reach the incoming VPN Clients.Is there any way to accomplish this? We need to access the branches subnets when connecting using VPN to the 2900 ISR.
View 1 Replies
View Related
Aug 7, 2012
I have a customer that wants to purchase an ASA 5510 security plus to terminate client VPN access for an external support team. The customer claims to want URL content filtering/proxy which leads me to suggest a CSC SSM 20 plus module. But upon further conversation, he mentioned wanting IPS. In this case, the customer does not seem to know the difference between the URL content filter/proxy and the IPS and uses both terms interchangably.
1. What would you suggest in your expert opinion would be the best module to get for this customer? IPS or CSC
2. If I go with the CSC module, where can I find good documentation on how to configure it and get it up to date?
3. does the CSC module provide any web proxy functionality?
View 3 Replies
View Related
Mar 22, 2012
I have found numerous posts discussing this but have yet to find a solution. I have an RV082 with firmware 2.0.0. 2.0.0.19-tm and I need a way to limit the incoming smtp traffic to just the spam filtering company.I have a port forwarding rule to forward WAN1 port 25 traffic to 192.168.1.10.I tried to add an access rule to deny all port 25 and then added one to allow WAN1 port 25 source <spam company> destination 192.168.1.10The RV082 log screen shows the traffic allowed but it does not work. If I uncheck the 'enable' box on the DENY port 25 rule email is still blocked. Only when I uncheck the 'enable' box on the ALLOW rule does email start flowing again.
View 10 Replies
View Related
Jul 25, 2011
I have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies
View Related
Oct 18, 2012
On a windows 2003 data server with a 2008 domain controller, I have several Terminal Servers that are setup to only allow one remote time entry program to run. Totally locked down from network / internet (Kiosk Mode). Now I need to be able to view pdf files in a directory. How can I do this without giving access to the disks that are available for the time entry program to write back. The time entry requires a mapped drive with read/write access. Every pdf viewer I have found so far gives the ability to "File Open/Save as" and thereby gives access the the shared drive. If I use an Internet Browser then I have the same problem.
View 1 Replies
View Related
Oct 9, 2012
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies
View Related
Dec 29, 2012
using a Linksys E2500. I have a Ubuntu "server" set up which i can access on my LAN through VNC Viewer (windows machines) no problem. I can even access it through the external IP address on a machine inside the LAN (both internal address and external address work from inside the LAN). I set up port forwarding (per portforward.com) but i still can not access my machine from outside the LAN. It has a static IP as well btw.
View 2 Replies
View Related
Feb 3, 2011
I purchased a RV082 router because it said it would support VLANs, but I cant seem to get it set up how I want.
I would like the first internet port on the router to feed one VLAN with an IP address. I would like the second internet port (DMZ / Internet) to feed a second VLAN with a different IP address. These two VLANs should be completely separate. I can see how to set up VLANs but I can seem to find how to separate the feeds and assign them different IP addresses.
Can I set up the RV082 to do this?
View 1 Replies
View Related
Oct 12, 2011
I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
View 4 Replies
View Related
Dec 17, 2012
I wanted to set Belkin Share Max n300 as an access point. I followed the instructions, set the IP address to the suggested one and connected it to the main router. It worked, computer connected to the Belkin via wire was getting IP address from DHCP on main router. But: The Belkin device itself became invisible. I lost connection to Belkin device via config page via HTTP. It does not respond to any IP address so I actually cannot use it for purpose I wanted to set up secondary Wi-fi, I just cannot configure it. Also I wanted to use USB ports of the Belkin to connect external drives. I cannot do it as well. More over it does not go back. It does not reset to the original router option.
View 2 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
May 7, 2012
i would like to "team" two ethernet ports on a 2921 router into a single redundant link to a switch, similar to how an HP server teams multiple NICs to a single IP address. is port-channeling the best/only way to do this? i don't necessarily need the two links to be load balanced or bonded, considering the serial side of this router is just a single T1. i just want the links redundant, so in case something goes wrong with one cable or switchport, traffic will go over the other link.
View 6 Replies
View Related
Sep 7, 2012
I just installed an HP nc360T into my home server, and I want to use both ethernet ports to get double the speed of a single 1gbt connection. Is there a way I can team 2 ethernet connections with DD-WRT? My router is the WNDR3700
View 4 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Feb 27, 2011
i am trying to forward port: 3754 on my westell A90-750022-07 gateway and i cannot get it to work? i made new rule and and when i try to enable it loads to a page with the menu bar on top but nothing in the body?
View 2 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
