Cisco WAN :: RV082 Setting Up Public Access To Web Server
Jan 13, 2011
I have a new (linksys/cisco) RV082 Router that I have just set up and everything is working except that I can't configure it to allow public access to our web server. I have tried configuring port forwarding under the Forwarding and UPnP menus and still no access from the outside. I have tried accessing it from the outside using both the URL and the IP address and still no access. I have checked with my ISP and no ports are being blocked from their end. I can ping my public static IP from the outside with no problem. The documentation that I've found for this router refers to a menu that is different from the menu of this router and refers to an Applications & Gaming menu which isn't there, but it seems like the port forwarding should handle this.
I have a static public IP, a static internal IP for the server. I have set the port forwarding and UpNP to point to the IP of the server using port 80 and a secondary forward to port 8080. There are no issues accessing the website from within the LAN.
View 2 Replies
ADVERTISEMENT
May 9, 2012
I am deploying a small wireless LAN (192.168.1.xxx) at a remote site and would like to access a PC at LAN IP address 192.168.1.2 across the Internet via TeamViewer so as to monitor devices on that LAN. The wireless LAN uses about 12 Cisco Aironet 1310 bridges in a ROOT-NONROOT (I guess this is point-to-multipoint?) configuration.Our ISP has given us a single static WAN IP address, subnet mask, gateway, and two DNS server addresses.
My intent was to assign our static WAN IP address from the ISP to our RV082 router, plug the LAN devices (including the PC at 1.2) into the RV082, and then use Network Address Translation (NAT) to forward TeamViewer traffic to the PC at 1.2. But the RV082's user manual says NOT to use the router's WAN IP address in the NAT table.So I'm confused as to how to send remote TeamViewer traffic to the PC inside my LAN. Is NAT not the way to do this? Should I be using port forwarding instead?I guess another way of skinning this cat would be to put a second NIC in the PC and let the second NIC have the WAN IP address so that it would be the first point of contact from outside, but that defeats some of my purposes for having the RV082 in the first place.
View 1 Replies
View Related
Nov 9, 2012
I want to use one (or two) AP1232AG-E-K9 access points for Internet connection through a public wireless network (BTFON), where wire broadband is not an option. I've downloaded what I think is the correct manual for the APs and I'm now scratching my head as to where and how to start setting them up. I want to use these Cisco APs in the hope they will give me better wireless performance than I'm currently getting, which is frequently flakey. I've tried to reset the APs to the factory default but there seem to be different ways of doing this depending on what you want and what you've got. I made up a console cable to access the console but there even appear to be different versions of this so I'm not sure if the cable I have is the correct one. I have setup and used lower end wireless devices in the past but these Cisco units seem real complicated.
View 39 Replies
View Related
Jul 25, 2011
I have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies
View Related
Jul 5, 2011
The router is 2821 and is setup to perform static NAT from one internal ip address mapping to one external ip address for each of our servers (inside the LAN): [code] Servers all have internal ip addresses and each of them represented to the outside world by their public ip address with above command on the router. Here is the problem.When I'm in a server (for example 192.168.0.210) and try to access other servers by their public ip addresses (i..e. *.*.*.211) the connection fails. However, When i try to access the same server by it's private IP address (i.e. 192.168.0.211) it works!
My issue is i don't want to modify windows host file for a manual mapping (for example mail.mydomian.com goes to 192.168.0.211 rather than *.*.*.211) because we host many domains and just doesn't make sense to do it one by one.So we must be able to access our servers by their public IP addresses in order for us our applications works correctly.
View 10 Replies
View Related
Feb 27, 2012
I've a problem with Cisco RV082. I want to connect to my public IP from local IP. But it seems it's been block by the firewall.I've added a firewall rules to allow ANY connection from LAN to outside world. But has no effect.
LAN IP : 192.168.1.5.Public IP (which is assigned to LAN IP 192.168.1.5 by One-to-One NAT) : 118.xxx.xxx.xxx
View 6 Replies
View Related
Aug 29, 2012
I recently "upgraded" to Uverse from DSL. While the speed boost is nice, UVerse comes with a 2wire residential gateway. Unfortunately you can't disable the DHCP functionality in the 2wire router, nor can you disable the router functionality completely and just run it as a modem, which has pretty much made it impossible to integrate into my network.So the partial solution anyway is to keep using the rv082 (yey!) behind the 2wire, assign a public static IP to the rv082 WAN1 i/f, disable the firewall in the 2wire for the rv082, and up and running again.The problem I'm facing now is that I had 3 devices on the LAN that were published using individual public static IPs. With good-ol'-DSL, I could use the one-to-one-NAT feature in the rv082, block any unwanted traffic in the firewall, and everything works. Unfortunately with the configuration options in the 2wire, I can only assign a single public IP address to any one device hooked up to it, in this case the rv082 WAN1 port.i have the one-to-one-NAT configured sequentially on the WAN and LAN side on the rv082 with nothing else hooked up to the 2wire. For example, one-to-one-NAT configuration in the rv082:
WAN range: 66.77.88.91 to 66.77..88.93
LAN range: 192.168.0.2 to 192.168.0.4
The 2wire is allocating the first public static IP in the range to the rv082 (i.e. 66.77.88.91). This works 100% reliably for this address - however because I can only assign a single address in the 2wire interface the other devices are no longer accessible externally. Curiously it kind of partially works, but not reliably. I can briefly connect to one of the other addresses (say xx.92), but then connectivity is lost to the others.Someone suggested I try using the Dual-WAN feature to get at least two addresses assigned to the rv082. Seemed like a good idea in theory, i.e. because the 2 WAN ports have different MAC addresses, the 2wire should see two different devices and allow me effectively to assign two public IPs to the rv082, e.g. 66.77.88.91 to WAN1 and 66.77.88.92 to WAN2. Of course failover mode won't work here, because only one is connected at a time. However the load-balancing mode did seem like it may work, but something is going on that I don't understand. Internal connectivity is working fine and I can access the internet, but for some reason the 2wire is getting really confused and constantly re-assigning IP addresses to the rv082. I don't know if this is because the host name is the same for both WAN1 and WAN2 ports, or there is something in how the rv082 does the load balancing.
- Is there any tricks to getting the Dual-WAN to work in the way needed to essentially have two simultaneous internet connections?
- Would it be possible to buy a 2nd rv082 and have it on the same LAN? How would I configure this?
- Is there an alternative Cisco router that may work better with what I'm trying to do?
View 9 Replies
View Related
Jun 22, 2012
I have to share some PDF files with members of my organization, I have a Windows XP Pro box dedicated for this. Currently they can access it from within the office as a shared folder. I would like to make it available remotely is there a better way other then as a FTP access.
View 1 Replies
View Related
Feb 3, 2011
I purchased a RV082 router because it said it would support VLANs, but I cant seem to get it set up how I want.
I would like the first internet port on the router to feed one VLAN with an IP address. I would like the second internet port (DMZ / Internet) to feed a second VLAN with a different IP address. These two VLANs should be completely separate. I can see how to set up VLANs but I can seem to find how to separate the feeds and assign them different IP addresses.
Can I set up the RV082 to do this?
View 1 Replies
View Related
Jun 10, 2013
We are setting up a vpn between a cisco RV082 and a checkpoint device. From the Cisco device we have set up (as remote IP) the public IP 85.xxx.xxx.xxx but when we try to start the tunnel the VPN log (from RV082) report the error "INVALID_ID_INFORMATION" as described below.
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: sending encrypted notification INVALID_ID_INFORMATION to 85.xxx.xxx.xxx:500
Jun 11 11:38:41 2013 VPN Log (g2gips1) #894: we require peer to have ID '85.xxx.xxx.xxx', but peer declares '10.yy.yy.yyy'
[code]....
The IP 10.yy.yy.yyy. reported in the log is the natted ip of the Checkpoint device.
View 3 Replies
View Related
Mar 25, 2013
How to setup 3 SG300-52 (in L2 mode) as per this diagram:Port 1 on all switches should be able to talk to each other and access the blob at the right.The ports 25 on the other hand should only be able to talk among themselves in their own private vlan. They are to carry sensitive traffic. So I created 3 vlans, vlan 78 for ports gi1, gi51 and vlan 10 for port25,49,50 and a dummy vlan: 666 with the intent of segratating vlan 10 from vlan 78. My attempts so far have failed. ports gi49-50 are configured as trunk ports and gi1,gi51 as access ports as the following cli output (excerpts of the startup config):
vlan database
vlan 10,78,666
exit
interface vlan 1
ip address 172.16.10.11 255.255.255.0
[code]....
Ports gi1 can talk to each other and access the blob but ports 25 refuse to talk to each other. But as soon as I remove the access links to the blob they can! Obviously, at that point port gi1 lose access.Is such a topology feasable or even advisable?
View 7 Replies
View Related
Jan 19, 2010
The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
View 8 Replies
View Related
Mar 9, 2013
I'm having an issue with the syslog.
My configuration is:
LAN A (RV042)<-> GW to GW tunnel <-> (RV082) LAN B
On LAN A, I got a NAS with a syslog server. On the RV042, I've set the parameters for the syslog server, and it's working fine. On the RV082, I've set the same parameters and noting is happening.
As troubleshooting, I've done the following:
-On the RV082, I can ping the NAS without problems.
-On the RV082, I've set my computer IP adress as syslog server IP and with packet analyser, I not seing any UDP packets.
View 6 Replies
View Related
Aug 21, 2012
We use the RV082 at some our sites. One particular site will not connect to the DNS server but all others will. I've checked every setting I can think of with no joy.
View 2 Replies
View Related
Jan 31, 2012
I've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?
View 1 Replies
View Related
Jun 17, 2012
Trying to setup split tunneling over Site-to-Site (Gateway To Gateway) VPN between RV082 and Win 2008 server. Tunnel seems to be ok, I can ping/access by IP hosts from both ends. But I can't get split DNS to work. Here is the setup
10.10.100.2 is the DNS server for xyz.local zone. It is at remote network.
The tunnel and routing work properly. I can ping 10.10.100.2 either from RV082 (system management - diagnostics) or from hosts at local network.
Moreover, I can run nslookup on a host from RV082 side (local network), set 10.10.100.2 as server to be queried and test dns resolution. names of hosts from xyz.local are resolved correctly. But. If I use nslookup on host to query RV082 as a DNS server and query for a host from xyz.local it responds that xyz.local is nonexistent domain. The same result I get trying to resolve/ping same name on system management - diagnostics page. Resolution of names from xyz.local fails. But Internet names are resolved
just fine.
I've tried to reboot the router, connect/disconnect the tunnel, set Domain Name fields of split DNS configuration pagein different ways including fqdn of hosts from xyz.local No effect. Just the same situation.
View 2 Replies
View Related
Nov 9, 2012
I got 1 public IP for router and 16 Public IP's for NAT from ISP. Both router IP in one range and the NAT IP's are in different range. I want to use 1 NAT public IP for one of my windows server.Am using cisco 1841 router, in which I ve configured the public IP provided by the ISP for router.
View 10 Replies
View Related
Jan 24, 2011
I cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
View 1 Replies
View Related
May 15, 2013
Could I get a validation that this config is correct in that it allows inbound access to the web server and that I should be able to ping it from my inside interface.
I tried to use the example code from Cisco DocID: 115904 for DMZ WebServer, but I found the object NAT parts did not work with my 8.6 IOS so I modified them as shown in my config.Example from 115904 doc.
!!!!
object network WebServerPublic
host 24.25.26.80
object network WebServerPrivate
host 192.168.1.80
nat(dmz,outside) static WebServerPublic service tcp www www ---> this does not code
!!!!
With the below code I do not get a ping reply sourcing from a 10.1.0.X host to 192.168.1.80 web server.And I cannot browse in from the outside to it either.I do see the MAC for 192.168.1.80 in the ASA's arp cache for the dmz interface.The web server is on a VMware ESX environment and I'm not sure it is set up correctly.
!
ASA Version 8.6(1)2
!
hostname A5515
!
interface GigabitEthernet0/0
[code]....
View 4 Replies
View Related
Jan 17, 2012
we need to implement a scalable solution where we can provide for each customer it's own public IP so that they can access some content restricted by IP range.the solution consists of a proxy software that will "listen" to multiple IP's, then reroute the HTTP requests and rewrite the URL's to a different format.Anyways, we came to the conclusion that what we need is the following:
- broadband line with a pool of 8 IP's
- a router that can support multiple IP's
- a server
what kind of router or device is required for this kind of configuration. basically the network diagram will be like this:
Internet ----> broadband -------> cable modem ------ > multiple static IP router -------> server NIC
we should be able to add the same above combination once we run out of IP's, another broadband line, another device and server ...
View 3 Replies
View Related
Feb 16, 2012
I have a virtual FreeNAS server running from VMPlayer and I want to allow my friends to connect to my media server from their houses, but I don't want to buy a domain. Is there a way to port them to it when they connect to my Public IP? I am willing to use another program if necessary. I have looked at Filezilla, but have the same issue.
View 4 Replies
View Related
Feb 20, 2012
i have a windows 2003 server using it as a proxy server with 2 nics. 192.xxx.xxx.xxx to the LAN and 172.xxx.xxx.xxx to the internet router. although I can browse on the LAN, i cannot ping any public ip. because of that i cannot use my outlook to get my mail.
View 1 Replies
View Related
Dec 14, 2011
Is there a simple way to have a web server have both a static public ip (I have a block of static IP's) and an static private ip (ex 192.168.0.60)? I am running a web project management application....
View 4 Replies
View Related
May 23, 2013
i can't get it working to expose on internal server to an outside interface.I used the public server function in ASDM.Internet access works if i nat my private adress to one of the available ipadresses provided by our isp.
Internal Server : owncloud 172.10.0.4
External Server : ext181 46.245.171.181
I can't see the error in the configuration,
: Saved
:
ASA Version 9.1(1)
!
hostname rhedetest
domain-name xxxxx.de
enable password 59t92OvRofWL9yf3 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code]....
View 10 Replies
View Related
Sep 11, 2012
I hava ASA5510. INSIDE,DMZ and OUTSIDE interfaces are configured. I hava web server on DMZ ip:10.0.0.1 and it is static natted to 1.1.1.1. From internet i can reach to web server with IP:1.1.1.1 and from INSIDE connect to web server with IP:10.0.0.1. Now i want to connect from INSIDE to WEB server via public IP(1.1.1.1).how can configure it?
View 2 Replies
View Related
Oct 8, 2012
Setup:
LAN (192.168.1.X, with .3 as gateway)
DMZ (192.168.2.X with .1 as gateway)
WAN (X.X.X.146 as primary public IP, .145 as gateway and .147-150 as additional public IPs)
I want to set it up so that X.146 is where all my outbound traffic appears to originate.I want tcp HTTPS and SMTP to be allowed from the WAN (via the X.147 IP) to a specific server (192.168.1.11) on the LAN.Also, HTTP traffic to X.148, X.149 and X.150 should go to DMZ and 192.168.2.8, 192.168.2.15 and 192.168.2.18 respectively, but I haven't added that to my config yet. Looking to get the HTTPS and SMTP ones working first, then I'll fix the others (one step at a time)I've got contact with the outside world when I've configured it using the ASDMs "Public Server" interface, but it refuses to properly establish the connection, I get a "SYN timeout".
My config:
: Saved
:
ASA Version 8.2(5)
!
hostname kcisco
enable password X encrypted
passwd X encrypted
names
[code]....
View 7 Replies
View Related
Apr 19, 2012
I'm trying via the ASDM to port forward http connections to a DVR for the purpose of viewing IP cams.I've tried via ASDM to create a public server but I'm not allowed to use my public IP address for the public Interface.I have only one public IP address available.Is there any way round this ? I would also like to know how I can enable NAT with PAT.I've tried setting the outside Interface for use with PAT but It keeps reverting to the setting for a range of external addresses.I'm not really used to the ASA cli yet , I'm getting there.If there's a workaround via the CLI , I'll take that route.
View 4 Replies
View Related
May 24, 2012
I'm having some trouble with my P660RU-T1 configuration. I have recently set up a linux SFTP server at my home and am trying to access it via my public ip (eg 1.1.1.1), the problem is this public IP goes to the router which doesnt pass on the requests to the server.Last summer when i first messed around with this i had no problems with using the public ip to access the server, its only recently.
View 1 Replies
View Related
Jul 30, 2012
I have an ASA 5510, one public IP address on my outside interface, an internal email server and a private network.I would like...
1: Users on my private network to be able to access the internet (PAT them to external outside address)
2: Email to be delivered to my MX (my single public IP address translated back to my internal email server.
i.e. can I share my single public IP address to serve translation in both directions (private users surfing the Internet (in-to-out) and an outside to inside NAT for email) ?
Email (MX) = 1.2.3.4
Public (outside) address = 1.2.3.4
Email server internal = 10.1.2.3
Internal private subnet for users = 10.0.0.0/8
View 1 Replies
View Related
Jan 10, 2012
I have a local web development server that I'd like to open up so my clients can see the sites I build for them. The server is just my old laptop that I now use only as a web server.
I'm having trouble figuring out the port forwarding for this. I have a Netgear WGR614v9. I've configured the server to have a static IP, and have port forwarding sending port 80 over to the server. I've made an exception in Windows Firewall for port 80.
So, from my understanding, I should be able to go to my http://[my public ip], and I should in the least see my servers default site.
I think my problem is that I don't have just one website hosted by Apache. But instead am using Virtual Hosts to have a handful of sites hosted. So what I don't know is how to configure the server to know what site to serve.
I know I'm missing a step with having DNS setup. I haven't gone through that step yet because I thought it wasn't immediately necessary to configure the port forwarding.
View 13 Replies
View Related
Sep 20, 2012
I've set up this router in the office, and I can access it via PPTP without any problems from home (via windows VPN), Router is sat in DMZ with full access to the internet.
Q1,I've created a 2 phase ipsec vpn with an IKE & preshared key (AES/MD5/1), but I can't find out how to get my encrypted hash for it?also, I can't access the IOS via telnet/ putty, I found an article online explaining how to enable it via url string, but it didn't work,
Q2,I've setup the cisco client on my laptop, and working on the pcf file, without much luck.. Everytime I try to connect it get " error 412. the remote peer is no longer responding. "
With wireshark, I can see the requests been made to the router.. ( from the office )
Within my PCF file i have ...
[main]
Description=MYNAME
Host=<external IP>
AuthType=1
GroupName=vpnname
GroupPwd=<myUnEncryptedKey>
[code]....
View 1 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Apr 29, 2013
I know this *should* be simple but having a devil of a time getting it to work.
I have 2 routers. Both have a static ip. Each is setup for a different private subnet. At the moment they are not connected to each other. Consider this setup (made up numbers obviously):
RV016
has 13 lan ports, 2 internet ports, 1 dmz port
Internet port: 10.10.10.10
[Code].....
I'd like clients on the rv082 lan to be able to access the printer on the rv016 lan, and use the rv016 as an alternate internet connection (optional). I would prefer the rv016 client not be able to access the rv082.
View 3 Replies
View Related
