I'm trying to setup an rv180w to connect as a client to an remote vpn gateway and route all the lan traffic behind it direct to the remote vpn gateway. [code]
View 3 RepliesI am trying to setup QuickVPN on my RV180W and having no luck. My client log shows "Remote gateway wasn't reached" "Failed to connect". The client is Win7 64-bit. I have created the firewall rule for icmpv4 on my windows 7 client but still no luck. I checked with my ISP and they say all ports are open. I have created the VPN user.
View 6 Replies View RelatedHave not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN logins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download.
Does buying RV180W allow download of Cisco Systems VPN Client software ?
Have not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN log ins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download. Does buying RV180W allow download of Cisco Systems VPN Client software ?
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
Is it possible to configure the RV180W VPN to use IPsec and connect to that VPN using the built in windows vpn client in Windows 7 and 8?I have been testing this but I have not been able to get it to work. What are the settings on the Router to make it compatable with the Windows VPN client?What are the settings I need in the Windows VPN client to allow it to connect to this router?I initially setup the QuickVPN client and that worked, but some of my users can't get it to work and I thought this might be a good alternative to try for those users.
View 8 Replies View RelatedI updated my RV180W to the latest firmware and found that port forwarding works I started using it.I've just noticed that since changing over to the RV180W, my Apacher server logs show the router's IP address instead of the remote IP address - every remote request appears to come from 192.168.0.1.
How do I get it to forward the remote IP.
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies View RelatedI am considering to buy two RV180Ws and place them on two separate locations. But before buying I would like to make sure that the units meets my requirements. Lets call the locations A and B. I would like to connect location A with full network access to location B. But at the same time I would like to have that location B also gets full access to the network at location A.Besides this I would like to be able to connect to one of the networks from remote with my laptop.Preferably all connections should be made using IPSEC and not PPTP.I would like to know if it is possible to make such a configuration, and eventually if there is a smarter way to do e.g. only letting clients connect to location A or B and granting them access to all ressources at both location A and B from there.
View 1 Replies View RelatedI have a RV042 and I am trying to setup a Client to Gateway VPN for about 12 to 15 remote users. These users travel a lot and need to connect to the server. I have never setup a vpn and have looked at the manual and set it up like it says to. I installed the Quick VPN client on the remote computer and copied the certificate to the remote computer.
I am having two problems.
1. When I run the client on the remote computer and try to connect it tells me the cert is not installed on the local computer. (it is copied to the root program directory C:Program Files Cisco Small Business and the sub directory, C:Program Files Cisco Small Business Quick VPN Client.
2. I can continue and it acts like it's connecting but it does not. If I look at the router VPN summary it shows that I connected for only a brief time.
I set up an RV042 as a VPN gateway for a client a year ago. It is running firmware 1.3.12.19-tm (Feb 13 2009 13:03:21). I created a new certificate. When I download the client certificate, It comes as a .zip file. One the can not be opened by a zip utlity (windows, Winzip or 7 zip). It looks like I can just rename the file to a .pem file, but I want to make sure that is right. They were getting QuickVPN timeouts, but that looks like it was fixed in 1.3.13.
View 3 Replies View RelatedI would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies View RelatedNew hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
I live in China. I want all of my PC's and devices to connect through the RV180W VPN Router to a VPN provider in the US so that all of my traffic is encrypted and appears to have a US IP address. I need to find a VPN Service Provider that supports the RV180W and how to configure it. I don't want to configure every PC and device, I just want them to use the VPN conneciton at the router.
View 3 Replies View RelatedI recently purchased a RV110W wireless router for a client. I am having issues with the VPN access. Here is the client's access log:
2012/04/17 10:59:41 [STATUS]Disconnecting...2012/04/17 10:59:47 [STATUS]Success to disconnect.2012/04/17 11:00:03 [STATUS]OS Version: Windows XP2012/04/17 11:00:03 [STATUS]Windows Firewall is OFF2012/04/17 11:00:04 [STATUS]One network interface
[Code].....
I've called Cisco tech support but the answer is disregard the log message and everything is working, and that I have a configuration issue on my end.
I'm trying to set up a RV042 to do the following:
1) Block all WAN connections, except for:
2) Allow all port 80 connections, and forward to 10.4.20.60
3) Allow all port 443 connections, and forward to 10.4.20.60
4) Allow port 22 connections from specific IP addresses, and forward to 10.4.20.60
5) After a remote client has connected using Client to Gateway VPN, allow that remote client to access anything on the LAN
I'm able to do #1-4 above, but I can't get #5 to work. Or I can get #5 to work, but can't implement the restrictions I need in #1-4. Attached are some relevant screenshots. I think the problem is that I have Forwarding rules set up that require me to have a firewall rule to Deny All Traffic from WAN1 (unless I'm specifically allowing it). In the Access Rules screenshot, rule #6 is the problem. If I enable it (thereby denying all WAN1 traffic), then VPN clinents can't access anything on the LAN. However if disable this rule, VPN clinents can access anything on the LAN, but the firewall also opens up all outside connections to SSH, since that's set up in the Forwarding rules. I would have thought that once a remote client is connected using client to gateway VPN, then that client is considered to be on the LAN, as far as the firewall is concerned. Thus a firewall rule (like #6) that is specified for WAN1 shouldn't effect remote VPN clients.
I have a RV180 router and i am trying to use the Quick VPN Client version 1.4.2.1. It works fine on my Windows 7 pc, and worked successfully once on the windows XP sp3 pc. But now the XP pc will not work.
What looks strange is in the VPN Client Connection Status on the router I see the status is Online, however the XP pc will not ping anything on the network or connect to the RDP pc i want. The QuickVPN Client hangs on "Verifying Network".
I tried the suggestions i saw online:
Disabling Firewall
Enabling Firewall
Making user name shorter
Allowing for PING on WAN (replies all come back fast)
Reboot Router
Upgraded firmware to 1.0.1.9
I did not adjust the MTU rate as i was not sure what to change it too. AV is AVG 2012.
Is there a way to configure RV180 to allow PPTP clients to route Internet traffic via its own internet connection?
I.e. supporting these client options: "Send all traffic" (Mac/iOS), "Use default gateway on remote network" (Windows).
I am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies View RelatedRouter is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
I've just set-up one of the RV220W VPN solutions. This worked fine for a while, but now it reports the remote gateway is not responding. Other clients can connect, but not the computer I'm using at home.
Log file reports:
2011/08/31 21:10:31 [STATUS]Success to connect.
2011/08/31 21:10:31 [STATUS]Tunnel is configured. Ping test is about to start.
2011/08/31 21:10:31 [STATUS]Verifying Network...
[code]...
I've tried the most common stuff. Enabling ICMP, checked that remote administration runs on port 443, changed MTU to 1400 manually, It allows fragmented packages too. Checked that IKE and IP Sec services are running. I've also tried both with windows firewall ON and OFF. A colleague of mine had the same problem in the same time frame as me, but after a while - he suddenly was able to connect. I still can't!!
Firmware Version: 1.0.2.4
Edit: IP is not real.
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
We have 2 remote locations that are connecting to a server at our home location. Each remote computer uses quickvpn utility to establish a vpn with the home location. Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008. Luckily our sessions in remote desktop stay put but we lose the vpn connection. Most of the time we get a message that the remote gateway is not responding. Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location. We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect.
View 3 Replies View RelatedI have a cisco RV180W with a IPsec tunnel to the head office. The tunnel is working good, but if I reboot the RV180W, the tunnel don’t reconnect automatically, I need to go in the admin interface to IPsec Connections Status and press on Connect.Is there a way to make the tunnel connect automatically?
View 4 Replies View RelatedI am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies View RelatedI have a need to Remote Desktop connect to company’s employees for support then they are abroad and using Cisco AnyConnect client.Cisco AnyConnect client connection works fine, clients can reach company’s inside network without problems, but I cannot make revers connection, I cannot Remote Desktop connect or ping VPN clients from companies inside network. I cannot ping clients from ASA too.I am using ASA 5520, Cisco Adaptive Security Appliance Software Version 8.4(3) Device Manager Version 6.4(7), and Cisco AnyConnect VPN Client 2.2.0133. Protocol Encryption- AnyConnect-Parent SSL – Tunnel DTLS-RC4 RC4 AES 128.
View 0 Replies View RelatedI setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedI picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly. What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there. For what its worth: While I have some IT experience, I don't have strong networking experience.
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site. Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up. Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected. But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me. I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
'TECHNICAL' SPECS
Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs
[URL]
Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?
View 1 Replies View RelatedI have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.
View 2 Replies View RelatedI have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc). I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity.
Routing does behave as advertised, where all traffic does go to the main office. However, the 192.168.1.0 subnet in the branch office does not get internet connectivity. I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet. Is there a way to configure the RV082 router to provide NAT for all subnets?
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets? Can the RV082 be used as part of the final solution or are my RV082s a wasted expenditure?
Following is the configuration that I'd implemented, (real IP and IKE keys are bogus).
Gateway To Gateway
Remote Main Office
Add a New Tunnel
Tunnel No. 1 2
Tunnel Name : n1-2122012_n2-1282012 n1-2122012_n2-1282012
Interface : WAN1 WAN1
[code].....
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies View Related