Cisco Routers :: RV220W Reports Remote Gateway Is Not Responding

Aug 30, 2011

I've just set-up one of the RV220W VPN solutions. This worked fine for a while, but now it reports the remote gateway is not responding. Other clients can connect, but not the computer I'm using at home.
Log file reports:
 
2011/08/31 21:10:31 [STATUS]Success to connect.
2011/08/31 21:10:31 [STATUS]Tunnel is configured. Ping test is about to start.
2011/08/31 21:10:31 [STATUS]Verifying Network...
[code]... 

I've tried the most common stuff. Enabling ICMP, checked that remote administration runs on port 443, changed MTU to 1400 manually, It allows fragmented packages too. Checked that IKE and IP Sec services are running. I've also tried both with windows firewall ON and OFF. A colleague of mine had the same problem in the same time frame as me, but after a while - he suddenly was able to connect. I still can't!!

Firmware Version: 1.0.2.4 
Edit: IP is not real.   

View 7 Replies


ADVERTISEMENT

Cisco Routers :: RV180 - QuickVPN The Remote Gateway Is Not Responding

Nov 19, 2012

I have a RV180 router and i am trying to use the Quick VPN Client version 1.4.2.1. It works fine on my Windows 7 pc, and worked successfully once on the windows XP sp3 pc. But now the XP pc will not work.
 
What looks strange is in the VPN Client Connection Status on the router I see the status is Online, however the XP pc will not ping anything on the network or connect to the RDP pc i want. The QuickVPN Client hangs on "Verifying Network".
 
I tried the suggestions i saw online:

Disabling Firewall
Enabling Firewall
Making user name shorter
Allowing for PING on WAN (replies all come back fast)
Reboot Router
Upgraded firmware to 1.0.1.9
 
I did not adjust the MTU rate as i was not sure what to change it too. AV is AVG 2012.

View 7 Replies View Related

Cisco Routers :: RVS4000 QuickVPN - The Remote Gateway Is Not Responding

Apr 4, 2012

I am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'

View 15 Replies View Related

Cisco Routers :: WRVS4400N And Quick VPN (remote Gateway Not Responding)

Jul 27, 2010

Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
 
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log  [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?

View 20 Replies View Related

Cisco Routers :: WRV210 - Quickvpn Disconnects - Remote Gateway Not Responding

Oct 2, 2012

We have 2 remote locations that are connecting to a server at our home location.  Each remote computer uses quickvpn utility to establish a vpn with the home location.  Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008.  Luckily our sessions in remote desktop stay put but we lose the vpn connection.  Most of the time we get a message that the remote gateway is not responding.  Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location.  We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect. 

View 3 Replies View Related

Cisco VPN :: WRVS4400N / Remote Gateway Is Not Responding

Oct 4, 2010

Im having trouble with getting my VPN to work on my brand new WRVS4400N router. i cant find the solution to my problem, no matter how much i read about it.
 
WRVS4400N:
Firmware Version: V2.0.0.8-ETSI
 
QuickVPN:
Version: 1.4.1.2
 
The laptop im trying to connect to the gateway via VPN is a Windows 7 x64 HP Elitebook 8540p with a internal mobile broadband (HSPA+)So.The scenario is that i've installed the QuickVPN client on my Win7-machine without any trouble.I've created a user in the web-administration of the router.The router is configured to disable "Block WAN requests" in the firewall, apart from that the firewall is on.When trying to connect - with a valid certificate that i created, i get a error message after the dialog telling me "Verifying network":"The remote gateway is not responding. Do you want to wait?".
 
The log.txt tells me:

...2010/10/06 00:00:28 [STATUS]Verifying Network...2010/10/06 00:00:34 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:37 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:40 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:43 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:46 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:49 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.2010/10/06 00:02:13 [STATUS]Disconnecting...

[code].....

View 2 Replies View Related

Cisco Routers :: How To Manage Port 80 Hosts Via Gateway To Gateway VPN (rv220w)

Aug 30, 2012

I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...

View 0 Replies View Related

Cisco Routers :: RV220W Gateway-to-Gateway Inter VLAN Routing?

Jul 6, 2012

I picked up a pair of RV220W's and before I spent loads of time at a remote site, I figured I'd go through some VPN testing at home to make sure I could get it setup properly.  What this means is I've plugged the Internet uplink into a switch, then from the switch into both routers & configured them (using unique static IP's for each) from there.  For what its worth: While I have some IT experience, I don't have strong networking experience.
 
I setup several VLAN's on the local RV220W, and the end result is to make it so that an asset at the remote site with an IP in any of the ranges (192.168.121.0/24, 192.168.131.0/24, 192.168.141.0/24 and any future VLANs) can communicate with/access resouces at the local site.  Likewise, an asset at the local site with an IP in any of the ranges (.121, .131, .141 + any future VLANs) should be able to reach the remote resources (currently just 192.168.181.0/24, but future VLANs as well).
 
This evening I tried to focus on the relevant VPN pages of the Administration Guide to get the VPN up.  Leaving the defaults I got as far as establishing a link between both sites and it seems that things are working right: From the remote site (.181) I can access the local site (.121, .131, .141); and from the local site I can at least ping resources (a laptop) on the remote site. (Yay!)
 
However, when I physically connected an asset that had a 192.168.121.X, 192.168.131.X and 192.168.141.X IP addresses to the remote RV220W (which is 192.168.181.0/24), I couldn't see it from the remote or local sites.I assume this is expected.  But I'm reaching out to the community to see what other possibilities might be available becuase networking is a weak area for me.  I figured it might be something like a Static [or Dynamic] Route but I really am not 100% sure.
  
'TECHNICAL' SPECS
 
 Local Router LAN/WAN Settings:
LAN IP: 192.168.121.1 on default VLAN (1)
VLAN 13 defined 192.168.131.1 with DHCP enabled; Reservations created outside of DHCP scope
VLAN 14 defined 192.168.141.1 with DHCP enabled, Reservations created outside of DHCP scope
Inter VLAN Routing enabled for all VLANs

[URL]

View 7 Replies View Related

Cisco Routers :: RV082 Gateway To Gateway VPN Not Resolving Remote DynDns

Feb 14, 2013

I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
 
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.

View 2 Replies View Related

Cisco Routers :: RV042 QuickVPN / Gateway Not Responding

Jun 28, 2011

I have router Linksys RV042 v1.2 with latest firmware Version: 1.3.13.02-tm. And I'm using QuickVPN v 1.4.1.2. I've setup VPN connection with values, below: But every time I'm trying to connect to router by VPN it always popup a window "Remote Gateway not responding".It occurs when I'm trying to connect to VPN behind other router, when I'm connected directly to Internet the connection is established.But I'm connecting to other networks using VPN and it's working properly (behind the same router), so I think it's problem with RV042 configuration but I don't now weher.

View 5 Replies View Related

Cisco Routers :: RV120W - QuickVPN Gateway Not Responding

Jan 1, 2012

I am trying to install a Cisco VPN Router RV120W behind this router. I have setup the Cisco and can access the internet from the device. I also setup the Actiontec router with the DMZ host as the Cisco router. When I try to connect to the VPN tunnel however I connect but receive an "Gateway is not responding" error message after 30sec. Is there anything else I need to setup on the actiontec router to allow VPN passthough or something like that?
 
 
Actiontec Lan IP: 192.168.1.1
Cisco Wan IP: 192.168.1.2
Cisco Wan SN: 255.255.255.0
Cisco Wan Gateway: 192.168.1.1
Cisco WAN DNS: 192.168.1.1
               71.250.0.12
Cisco Lan IP: 192.168.20.1
 
Edit: I have also tried this connection from a Windows 7 Pro with Firewall enabled and also Windows XP with the same error.
 
Quick VPN log:
 
2011/12/30 00:05:58 [STATUS]OS Version: Windows 7
2011/12/30 00:05:58 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:05:58 [STATUS]Windows Firewall Private Profile Settings: ON
2011/12/30 00:06:10 [STATUS]OS Version: Windows 7
2011/12/30 00:06:10 [STATUS]Windows Firewall Domain Profile Settings: ON (code )

View 9 Replies View Related

Cisco Routers :: RV220W Cannot Reach Gateway Or Any Host Behind It

Oct 31, 2012

I have created a connection gateway-to-gateway between RV220W and RVL200, is doing without any problems.For example, I can ping the gateway on the other side. But when I connect trough RV220W QuickVPN (or PPTP) I can not reach the gateway (RVL200) or any host behind it.

View 4 Replies View Related

Cisco Routers :: Setting Up RV220W Behind Comcast SMC Gateway

Jun 25, 2012

I spoke with the Comcast gateway support team and they changed my SMC router to the straight gateway/bridge option. If I plug directly from my laptop to the SMC, I have internet connectivity. So I know that aspect is working. I have a Cisco RV220W router that I want to be between the internet/SMC gateway and my network. For the life of me, I cannot get the internet connectivity to pass through to the router. I've done the proper power on order numerous times. Tried variations just for the heck of it. And nothing. Am I missing a step? If I do the "wizard" on the router, it basically tells me it sees no gateway even available even though it is clearly there and plugged into the WAN port. I don't see any option in the router settings for me to specify like the DHCP server I should be reaching out (if there even is one). My understanding is I shouldn't need to as the router should just recognize it.  Should I be using a static IP instead?

View 3 Replies View Related

Cisco Routers :: RV220W Remote Administration Not Working

Oct 26, 2011

RV220W is at firmware v1.0.2.4 From: Administration / Management Interface / Web Accesss I have configured remote Management: Remote Management [x] EnabledAccess Type: All IP addressesPort Number: 8888Remote SNTP  [  ] not enabled
 
From within the LAN side I can connect to the router and administer via https://192.168.3.97:8888
 
Status / System Summary reports:WAN (Internet) Information (IP4)
Connection Type: Static
Connection State: Connected
IP Address: 207.180.139.242
NAT:  Enabled
But from the WAN side (using the same Win7 computer) I cannot connect via:  https://207.180.139.242:8888
 
This used to work.   Also not working:  PPTP logins.   ISP is RCN via cable modem, fixed IPs.
 
Have tried power cycling router - no luck. Have tried from PC with AV off and Win7 firewall off

View 5 Replies View Related

Cisco Routers :: RV220W Remote PPTP VPN Connection Fails?

Jan 23, 2012

i'm having problems connecting to my RV220W using PPTP. The first time I set up PPTP on the box, everything worked just fine. Now, however, PPTP just won't work. No matter how I try to tweak various settings on the router, the connection fails. I have tried connecting with Windows 7, Android and OSX with no success.The router came with version 1.0.1.0, and I have tried downgrading to 1.0.0.26 and upgrading to 1.0.3.5, but alas, I can't seem to make PPTP work again.

View 1 Replies View Related

Cisco Routers :: RV220W Upgrade To 1.0.4.17 - Now Remote Desktop Won't Connect

Sep 16, 2012

Or rather, it will connect within the first few minutes after a router reboot, but eventually is kept from connecting.
 
All settings look good. Upgraded from 1.0.3.5.  Prior to upgrade, this was not  problem.

View 3 Replies View Related

Cisco Routers :: RV220W V1.0.2.4 Remote Management / Load Balanced Proxy Fail?

Sep 26, 2011

I just purchased 5 RV220W to act as internet/wireless router at a remote site. There is no VPN, just LAN and Wireless routing to the internet.I have setup remote management and it works fine when I am directly connected to the internet. However, everytime I try to connect through our HTTP/HTTPs proxy farm, it usually fails. Specificially, I get the log-in page and can log in. It starts to render the landing page but redirects to a page stating "Your session has been terminated." On rare instances the first page will appear, however within a few clicks I end up with the same terminated page.
 
As a test, I bypassed the farm and forced my browser to use one proxy exclusively. At that point I could access the HTTPS interface with no issue. I have not had any issues with other SSL sites with the proxy configuration in use.Is there some sort of MITM prevention I could be running into? If so, can it be turned off.I am new to the RV-series of routers. Is there any logging I could turn on that would provide insight on why the session may be getting terminated?

View 2 Replies View Related

Cisco Routers :: RV110W Ping Remote Gateway

Apr 16, 2012

I recently purchased a RV110W wireless router for a client.  I am having issues with the VPN access.  Here is the client's access log:
 
2012/04/17 10:59:41 [STATUS]Disconnecting...2012/04/17 10:59:47 [STATUS]Success to disconnect.2012/04/17 11:00:03 [STATUS]OS Version: Windows XP2012/04/17 11:00:03 [STATUS]Windows Firewall is OFF2012/04/17 11:00:04 [STATUS]One network interface

[Code].....
 
I've called Cisco tech support but the answer is disregard the log message and everything is working, and that I have a configuration issue on my end. 

View 2 Replies View Related

Cisco Routers :: RV180 PPTP Clients - Using Remote Gateway

Jul 31, 2012

Is there a way to configure RV180 to allow PPTP clients to route Internet traffic via its own internet connection?
 
I.e. supporting these client options: "Send all traffic" (Mac/iOS), "Use default gateway on remote network" (Windows).

View 1 Replies View Related

Cisco Routers :: RV180w To Connect As Client To Remote VPN Gateway

Jun 1, 2013

I'm trying to setup an rv180w to connect as a client to an remote vpn gateway and route all the lan traffic behind it direct to the remote vpn gateway. [code]

View 3 Replies View Related

Cisco Switching/Routing :: 4500 Switch Reports Ports As 10 / Full While Other Side Reports 100

Oct 31, 2011

we have a 4510r-e running  12.2(50)SG1 w/ various rj45 line cards and a 24 port glc card.at any given time, i see 10's of ports in 10/full.i go to the station, and find the station in 100/full or 1000/full.

i go to the switch w/ my fluke, connect it directly to the switch w/o any intermediate infrastructure except a 50cm cat6 patch cable.the fluke reports 1000/full, but THE SWITCH PORT REPORTS STILL 10/FULL.all ports are config'd 'speed auto'  and 'duplex auto'.
 
the switch  seems to be erroneously reporting 10/full.there are no errors logged on any of the ports and there is successful communications even when the station and switch port report different speeds.even though there are no errors logged nor reported  by 'show int [port]' nor 'sho int count error' certain killer applications crash on some stations. (the applications are GHOST (which dumps disk images from a server to multiple stations) and NETOP (which i sused in a classroom to transmit an instructors screen to a room full of stations)  both of which broadcast and/or multicast.all nodes involved in the above 2 applics are on the same vlan and same phyiscal subnet.

the ports which report 10/full vary and occur even when the above applics are not in use.the only way i found to clear this 10/full report is by either a hardware reset of the entire module or by unplugging the cable, the execute on the port shutdown, speed auto, no shutdown, reconnect cable.then it's just a matter of time until it pops back to 10/full in a few minutes,hours or days.
 
how to address the killer applic problems besides restructuring the whole net by defining separate vlan for each lab of 20 or so stations?

View 7 Replies View Related

Cisco VPN :: ASA 5510 - Gateway Not Responding?

May 8, 2013

What this error means from a Cisco VPN client when trying to connect to a ASA 5510?
 
VPN Error
VPN gateway not responding (waiting for Msg 2)

View 3 Replies View Related

Cisco VPN :: QuickVPN - Gateway Not Responding - RV042?

Oct 28, 2011

I'm running Cisco QuickVPN on a clients laptop (Windows 7). Windows firewall is disabled because McAfee SaaS is running.I sometimes have the issue that the initial connection attempt comes back with "Gateway not respoding" during the network verification process. You close the program, you open it again and it works. Sometimes it takes 2 or 3 tries. Today I have the issue that my client tried it like 20 times including several reboots and it's just not working. I tried it from my own computer and it connected fine on the 2nd try.I'm thinking that it might be time-out thing, that the VPN client doesn't receive a response fast enough? I know my clients home internet is darn slow.

View 1 Replies View Related

DNS Server Not Responding And Default Gateway Is Not Available?

Sep 29, 2012

I have been having some trouble with my internet for awhile now. It fine one second and than it will get really slow and eventually stop working. When I troubleshoot to see what the problem is it either gives me DNS server is not responding or default gateway is not available, sometimes it will give me both. It says it fixes the default gateway problem but it will show up again 5 minutes later.

Here is my ipconfig /all
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.

[Code].....

View 5 Replies View Related

Cisco VPN :: PIX-515E Remote Peer Is No Longer Responding

Jul 8, 2012

I am unable to VPN to my network from outside using cisco VPN client to PIX-515E. When I try it say: Reason 412: the remote peer is no longer responding. From inside everything work ok, I can connect... (same computer, same settings...)

View 3 Replies View Related

Login Failure Due To Remote Host Not Responding

Nov 2, 2011

I am able to connect via VPN from my office wireless. In my home I am not able to connect. I got the error as Login Failure Due to Remote host not responding. I have wireless connection in my home. I am able to surf internet and also able to ping the ip mentioned in VPN.

View 3 Replies View Related

Cisco VPN :: RV220W What To Enter For Remote WAN In VPN Wizard

Apr 8, 2011

I have just received my RV220W Small Business Router and I do not understand the manual/UI wrt VPN. In the past, I had a PPTP server running behind a NAT and I used Pass Through to get external clients (Macs) to connect to my local LAN.  But now I would like to use the Cisco Router's VPN capabilities to set up VPN and shut down the PPTP server in my LAN.I have a couple of fixed IP addresses that end up on this router, wit ISP-based 'technical' domain names (e.g. foo.static.isp.com) with reverse lookup, so using those, I should be able to connect to my RV220W from the outside.

View 0 Replies View Related

Cisco Routers :: RVS4000 To Use A Gateway To Gateway IPSec Tunnel

Oct 17, 2011

Can I have use a Gateway-to-Gateway IPSec tunnel whereby a user can surf the Internet using his local Internet connection and at the same time connect through the IPSec tunnel to a remote subnet using RVS4000 routers?

View 1 Replies View Related

Cisco Routers :: RV042 Gateway To Gateway Tunnels Not Reconnecting

Apr 11, 2013

I have two Cisco RV042 Routers, they are being used to connect two offices, i have created a standard gateway to gateway connection, fixed public ip addresses on both sides and everything works fine, except when the tunnel gets disconnected, it does not connect back automatically, i have to log into either  router console and click the connect button to get the tunnel working again, this is really annoying since it happens once or twice a day at least.

View 2 Replies View Related

Cisco Routers :: RV016 Gateway To Gateway RV082 Won't Connect

Mar 9, 2012

New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway  VPN
 
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address  some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
 
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address  some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
 
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.

View 2 Replies View Related

Cisco Routers :: Getting VPN Gateway To Gateway With NAT For Multiple Subnets / RV082?

Feb 11, 2012

I have a pair of RV082 routers and I'd like to configure gateway to gateway VPN tunnel as described in a cookbook, "How to configure a VPN tunnel that routes all traffic to the Remote Gateway," (file name Small_business_router_tunnel_Branch_to_Main.doc).  I followed this cookbook and found that my while the Main office has internet connectivity, the branch subnet doesn't have internet connectivity. 
 
Routing does behave as advertised, where all traffic does go to the main office.  However, the 192.168.1.0 subnet in the branch office does not get internet connectivity.  I've read in other posts that the Main office router will only provide NAT for the local subnet, not the branch office subnet.  Is  there a way to configure the RV082 router to provide NAT for all subnets?
 
If not, which Cisco product will provide the VPN Tunnel connectivity as well as the NAT for all subnets?  Can the RV082 be used as part of the final solution or are my RV082s a  wasted expenditure?

Following is the configuration that I'd implemented, (real IP and IKE keys are bogus). 
  
Gateway To Gateway    
Remote                                                   Main Office
 Add a New Tunnel
Tunnel No.                  1                                               2
Tunnel Name :               n1-2122012_n2-1282012        n1-2122012_n2-1282012
Interface :                  WAN1                                    WAN1

[code].....

View 2 Replies View Related

Cisco Routers :: RV8082 Setup A VPN Tunnel With Gateway-to-Gateway

Apr 8, 2012

I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway.  One location is a static IP Address.  The other location is a dynamic IP address.

View 2 Replies View Related

Cisco Routers :: Gateway To Gateway VPN Between RV110W And RV042G?

Mar 19, 2013

I am trying to set up a gateway to gateway VPN connection between a RV042G (central site) and a RV110W (newest firmware) which is used for presentation purposes on various customer's sites. The RV042G has a static IP. The RV110W has different IPs, depending on where it is used.
 
Basic VPN settings are clear to me (we have another VPN between two RV042G with static IPs). I set up the VPN connection on the RV042G wth the following settings for "Remote Group Setup":
 
Remote Security Gateway Type : IP + Domain Name (FQDN) Authentication IP by DNS resolved: mydomain.no-ip.org Domain Name: router12345
 
The value "router12345" is what I have configured in the RV110W as "Host name" in the network settings.
 
This configuration does not work so I am obviously doing something wrong. Do I have to use "router12345.mydomain.local" instead if I configured "mydomain.local" as the domain name in the RV110Ws network settings? For my tests the RV110W has a WAN-IP of 192.168.178.100 because it is located behind a DSL-Router. The external IP of this DSL-router is 178.0.x.x. The resolved IP  from mydomain.no-ip-org is 192.168.178.100 but when I look in the RV042G log I see the requests coming withg the external IP (178.0.x.x). Is this the problem? The last message I see in the log is "no connection has been authorized with policy=PSK".
 
Or can I use "IP + Email Address (USER FQDN) Authentication" instead (where can I enter this email address in the RV110W?). Or do I have to use "Dynamic IP"?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved