I am able to connect via VPN from my office wireless. In my home I am not able to connect. I got the error as Login Failure Due to Remote host not responding. I have wireless connection in my home. I am able to surf internet and also able to ping the ip mentioned in VPN.
View 3 Replies
I have a host that can successfully connect to a PIX 515E (7.x OS) via VPN Client; however, I have no IP routing to the LAN from the remote host.The VPN IP pool works finem,The LAN default gateway is the inside interface on the PIX; the network is flat L2 behind it.The default route on the PIX points out; no other routes are defined,The VPN remote host can be pinged from LAN hosts, but the VPN remote host cannot ping any LAN host, not even the PIX inside interface.
View 2 Replies View RelatedI bought a new DIR-615 and tried to install dd-wrt on it. During the installation all of a sudden the router stopped blinking the led lights and stopped responding to anything. It's current status is that I can only see globe LED and the other 4 LAN LEDs in continuous green and NOT blinking. The power LED and wireless LED are not even displaying. I tried all kinds of reset like soft,hard and crash but no response. It's not responding to anything except those 5 LED lights.
View 1 Replies View RelatedWe have an ACS 4.2 installation and we have users configured on the user setup, they authenicate using the windows database (AD). We ran failure tests and simulated AD failure but disabling the firewall rule. So the ACS server is up, AD is down. Tested user login to a switch and get the following error. External DB user invalid. It looks like as the ACS does not get a response from AD it rejects the user login.
What we want it to do is in the event of AD failure is to be able to login to the switch with the username configured on the switch. (as if ACS server does not respond)
Date Time Message-Type User-Name Group-Name Caller-ID Network Access Profile Name Authen-Failure-Code Author-Failure-Code Author-Data NAS-Port NAS-IP-Address Filter Information PEAP/EAP-FAST-Clear-Name EAP Type EAP Type Name Reason Access Device Network Device Group 02/03/201214:09:13Authen failedtest.testNetwork192.168.1.1(Default)External DB user invalid or bad password....tty310.0.0.1..........SWITCH30Office
I want to make my switch send trap when failed SSH login is detected. I found the "login Enhancement" feature and enabled the trap and logging for the failed attempt.
3750# sh run | in login
aaa authentication login default local
login delay 1
[Code].....
The Lg840g is a tracfone with wifi capability. I get strong wifi signal and connection at home, but receive failure to connect to requested host message when I open the browser. This phone works at wayport wifi, so I assume it's a compatibility problem with the router. Is there a fix? (Router works great with our Acer and Kindle tablets though.)
View 1 Replies View RelatedIm having trouble with getting my VPN to work on my brand new WRVS4400N router. i cant find the solution to my problem, no matter how much i read about it.
WRVS4400N:
Firmware Version: V2.0.0.8-ETSI
QuickVPN:
Version: 1.4.1.2
The laptop im trying to connect to the gateway via VPN is a Windows 7 x64 HP Elitebook 8540p with a internal mobile broadband (HSPA+)So.The scenario is that i've installed the QuickVPN client on my Win7-machine without any trouble.I've created a user in the web-administration of the router.The router is configured to disable "Block WAN requests" in the firewall, apart from that the firewall is on.When trying to connect - with a valid certificate that i created, i get a error message after the dialog telling me "Verifying network":"The remote gateway is not responding. Do you want to wait?".
The log.txt tells me:
...2010/10/06 00:00:28 [STATUS]Verifying Network...2010/10/06 00:00:34 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:37 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:40 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:43 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:46 [WARNING]Failed to ping remote VPN Router!2010/10/06 00:00:49 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.2010/10/06 00:02:13 [STATUS]Disconnecting...
[code].....
I am unable to VPN to my network from outside using cisco VPN client to PIX-515E. When I try it say: Reason 412: the remote peer is no longer responding. From inside everything work ok, I can connect... (same computer, same settings...)
View 3 Replies View RelatedI have a RV180 router and i am trying to use the Quick VPN Client version 1.4.2.1. It works fine on my Windows 7 pc, and worked successfully once on the windows XP sp3 pc. But now the XP pc will not work.
What looks strange is in the VPN Client Connection Status on the router I see the status is Online, however the XP pc will not ping anything on the network or connect to the RDP pc i want. The QuickVPN Client hangs on "Verifying Network".
I tried the suggestions i saw online:
Disabling Firewall
Enabling Firewall
Making user name shorter
Allowing for PING on WAN (replies all come back fast)
Reboot Router
Upgraded firmware to 1.0.1.9
I did not adjust the MTU rate as i was not sure what to change it too. AV is AVG 2012.
I am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies View RelatedRouter is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
I've just set-up one of the RV220W VPN solutions. This worked fine for a while, but now it reports the remote gateway is not responding. Other clients can connect, but not the computer I'm using at home.
Log file reports:
2011/08/31 21:10:31 [STATUS]Success to connect.
2011/08/31 21:10:31 [STATUS]Tunnel is configured. Ping test is about to start.
2011/08/31 21:10:31 [STATUS]Verifying Network...
[code]...
I've tried the most common stuff. Enabling ICMP, checked that remote administration runs on port 443, changed MTU to 1400 manually, It allows fragmented packages too. Checked that IKE and IP Sec services are running. I've also tried both with windows firewall ON and OFF. A colleague of mine had the same problem in the same time frame as me, but after a while - he suddenly was able to connect. I still can't!!
Firmware Version: 1.0.2.4
Edit: IP is not real.
I have been unable to access my WHS when I recently traveled across the US. I have a Netgear WNDR3700 router. My DSL modem is a DSL-520B. I have AT&T DSL (6 Mbs). I have tried enabling and disabling "remote management", forwarding to ports 80, 443, 3390, and 4125 all with no success.Also, I believe (correct me if I am wrong) the remote management address is incorrectly listed as http://192.168.1.2:8080. I have also turned off USB storage in case of a possible conflict I have read about with port 80.
View 4 Replies View RelatedWe have 2 remote locations that are connecting to a server at our home location. Each remote computer uses quickvpn utility to establish a vpn with the home location. Our problem is that sometimes the vpn disconnects while we are working in remote desktop on server 2008. Luckily our sessions in remote desktop stay put but we lose the vpn connection. Most of the time we get a message that the remote gateway is not responding. Our dsl internet connection seems to work and we have previously had no trouble with connecting to the home location. We have 3 computers that connect simultaneously to the server at each remote location and sometimes one computer will stay connected while others disconnect.
View 3 Replies View Relatedi have to get a 2811 acting as a terminal server?
View 11 Replies View RelatedInstead using RDP, is it possible to login to a window box remotely?
View 2 Replies View RelatedNot very familiar with ASA and NAT'ing in general so hopefully, this will make sense.
I've created a Site-to-Site IPSec VPN tunnel with one of our clients (who uses a PIX). The remote user can connect to our local, private LAN servers without a problem. However, when the remote user tries to connect to servers on our corporate network (which is linked over WAN routers from LA to Dallas) they cant get through.
When I run Packet Trace in ASDM on our ASA all is well until the packet attempts to traverse from the Inside interface back through the Outside interface (back to the remote client side of the VPN tunnel).
I see the following "error" within the Packet Trace tool;
-----------------------------------------------------------------------------------------
Type - NAT Subtype - rpf-check Action - DROP
Config
object network obj_any
nat (inside,outside) dynamic interface
-------------------------------------------------------------------------------------------
I've attached my ASA config. The remote client-side address is 74.8.221.195, its being PAT'd to 172.30.12.75 and the remote host/network its not able to reach is 172.30.101.20 ( /24 net mask). The local segment in my LA network is 172.30.12.0/22 and the servers in this network are all able to communicate with the remote client-side user at 74.8.221.195.
How do I setup remote login that would allow 3 or 4 people to login to the same computer.Each person would have their own Windows User Account name, with different privileges.I don't know what software could do this. The computer being connected to would be Windows 7, and there is no special network equipment besides a consumer router.
View 11 Replies View RelatedI work from a remote location, and use a VPN to access files on the company server. I have no problem logging into the VPN, but when using Windows 7 64-bit, I am denied access to the specific folder containing the files I need, even though I can see and open other folders on the same server.
However, if I connect from an old laptop running Windows 2000, I get a login pop-up when I click on the desired folder and after entering my username (including the remote domain name) and password I can access the files. In the newer OS, I just get a stock "access denied" message, with no option to log in. Specifically, in W7 the message is "You do not have permission to access this folder", which is nonsense.
Our IT department is baffled. How to set up W7 so it will allow me to log into the protected folder in the same way I can do it in W2K? Once logged in to the VPN itself, I use the 'run' command with the remote IP address to bring up the folders in a normal Explorer window.
I can connect to the free wireless with no problem on my company laptop. Last night, I was using my personal laptop (as I have been for 2 weeks) on the wireless internet when I suddenly lost connection. In the Network and Sharing center of Windows Vista it shows a connection to the router but an 'X' between the router and the internet. When I run the diagnostic I get "Cannot communicate with primary DNS server (4.2.2.1)" The it says "Network diagnostics pinged the remote host but did not receive a response".
View 14 Replies View RelatedI have created a RA VPN with a 5505 using Anyconnect client. My VPN functions perfectly, but now I am trying to limit access so that only one single host on my network can connect. To do this I tried creating an ACL permiting the host and denying all other traffic, but it does not work it seems every one can connect. how I can limit the outside access to a single host?
View 3 Replies View RelatedI am in a test environment using an ASA 55005 and a Cisoc 2611xm router. ASA is running version 8.4 and router is running is ios12.4. My VPN tunnel comes up but I am unable to ping between remote hosts. I used the ASDM and SDM for the configuration. Attached is a copy of both configs.
View 8 Replies View RelatedI am trying to telnet to my asa 5510 from the core swith,however i received the below msg,how enable it?
172.30.1.100 is the inside interface of the asa
CITYCORE#telnet 172.30.1.100Trying 172.30.1.100 ... % Connection refused by remote host
CITYCORE#
On remote site I have Cisco ASA5505, on cental site I have Cisco 2811 router, working site-to-site VPN tunnel. [code]
View 1 Replies View Relatedi provide 192.168.1.201 and port No.8150 in CP Plus DVR . I am able to login through Local system via IE with [URL] after pressing enter key Login window appears. I will type User ID as Admin and password 888888. now i am able to enter DVR and view all cameras. no problemin Beetal ADSL router ( ISP Router) i configured port forwarding as followsIP address 192.168.1.201 and Port No. 8150 both internal & external.Now i got internet IP address through MY IP Address.the IP address is 59.92.67.72 ISPs IP address for my Borad Band.through another internet with different different ISPI open IE and type [URL] got same loging window as in LANagain I enter User Id as Admin and password 888888but shows login failed Message through internet I got the same login window when i tried through LAN, but I am to unable login with a message login failed
View 1 Replies View RelatedI found a bug in Embedded Event Manager, on Catalyst 4500-E platform with supervisor V-10GE, on various IOS releases (in particular 12.2-50-SG IP BASE w/o crypto, 12.2-54-SG1 IP BASE w/o crypto, but also other releases included latest 15.0-2-SG1 ENTERPRISE SERVICES SSH).The problem is that when you set up a EEM applet that monitors syslog pattern matching, and you also configure remote host logging *with* the option "sequence-num-session", when the match occurs, the switch reboots with message:
Sw (sometimes prints a number instead)
VECTOR D00
and in some cases performs a second reboot with message:
VECTOR 0
DOUBLE FAULT
The reload reason message is:
System returned to ROM by abort at PC 0x0
The problem does *not* occur if remote logging has not the option "sequence-num-session". I verified this behavior on various configurations (included our production 130K long *and* factory defaults after erase startup-config).The configuration statements that cause reload are, for expample:
event manager applet prova
event syslog pattern %SYS-5-CONFIG_I
action 1.0 puts "configurazione modificata"
!
logging host 172.30.10.1 sequence-num-session
Is there any way to Mirror a CISCO C3750 Switch Port Taffic to a remote Host IP Address?I know Port Mirror (SPAN/RSPAN) can copy one Interface Packet to another Interface. But I am looking for a way to miror Switch Port Packets to a remote Host (having Public IP Address and running Wirehark). Is it possible?
View 9 Replies View Relatedlets you catalyst 3560 & 2960 remote login with a secure protocol
View 4 Replies View RelatedMy first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies View RelatedI'm just wondering if its possible to ping an IPv4 host using the IPv6 host assuming that the NAT64 has already been implemented?
[code]...
ASA 5510
Ver 8.2(5)
I have been looking all over the place for the answer of how to allow clients on an IPSEC VPN to ping from host to host.
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies View Related
