Cisco Routers :: RV180W VPN Using IPsec And Windows 7 / 8 Built In Client
Apr 10, 2013
Is it possible to configure the RV180W VPN to use IPsec and connect to that VPN using the built in windows vpn client in Windows 7 and 8?I have been testing this but I have not been able to get it to work. What are the settings on the Router to make it compatable with the Windows VPN client?What are the settings I need in the Windows VPN client to allow it to connect to this router?I initially setup the QuickVPN client and that worked, but some of my users can't get it to work and I thought this might be a good alternative to try for those users.
I try to connect to RV220W with windows 7 client but I fail : error 789. I compare again and again pre shared key, but it doesn't change anything. How to connect to RV220W with IPsec client ?
I am setting up a customer site. One side is RV180W and the other side is Checkpoint 500W.
RV180W side LAN - 192.168.100.0/24 Checkpoint side LAN - 172.26.1.0/24 VOIP - 172.26.2.0/24
Need to setup an ipsec tunnel between the site. However, from the RV180W side, I can only ping the VOIP network, but not LAN. I have heard that RV180W only can talk to one remote network via ipsec, correct? workaround this other than changing out the RV180W?
Have not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN logins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download.
Does buying RV180W allow download of Cisco Systems VPN Client software ?
Have not purchased RV180W at this time, therefore have not read manual. Need for small office, 2 VPN log ins max & not 24x7 use. What VPN client software ? (using Win7-64bit laptops)
I did notice software called Quick VPN Client 1.4.2.1 for download. Does buying RV180W allow download of Cisco Systems VPN Client software ?
I have a cisco RV180W with a IPsec tunnel to the head office. The tunnel is working good, but if I reboot the RV180W, the tunnel don’t reconnect automatically, I need to go in the admin interface to IPsec Connections Status and press on Connect.Is there a way to make the tunnel connect automatically?
I'm trying to setup an rv180w to connect as a client to an remote vpn gateway and route all the lan traffic behind it direct to the remote vpn gateway. [code]
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
I have difficulties with configuring Remote IPSec VPN with Cisco ASA 5505 and Windows 7 native VPN client. My client PC gets VPN pool IP address, and can access remote network behind ASA, but then I lose my internet connectivity. I have read that this should be an issue with split tunneling, but I did as it is told here and no luck.On Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have internet connectivity (since client is using local gateway), but then, I cannot ping remote network.In log, I see this warnings of this type:Teardown TCP connection 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0:00:00 bytes 0 Flow is a loopback (cisco)I have attached my configuration file (without split-tunneling configuration I tried). If you need additional logs I'll send them right away.
I'm having problem establish l2tp/ipsec vpn connection from Windows vista/7 vpn client to cisco 1921 ( ios 15.2 ) C1 --------> (internet cloud) ---------> (cisco 1921)----->LAN
Error that I'm retrieving is always the same: Error 789: "The L2TP connection attempt failed because the security layer encountered a processing error during initial negotiations with the remote computer"
But I'm able to establish l2tp/ipsec vpn connection to the same vpn server with my iPhone 4.
Below is isakmp debug log from lns router(cisco 1921) when I've tried to establish vpn with windows client. Anything useful from these logs to point me on the right direction to finally solve this problem with windows clients.
#debug crypto isakmp *Apr 8 10:56:47.018: ISAKMP (0): received packet from 186.51.43.137 dport 500 sport 987 Global (N) NEW SA *Apr 8 10:56:47.018: ISAKMP: Created a peer struct for 186.51.43.137, peer port 987 *Apr 8 10:56:47.018: ISAKMP: New peer created peer = 0x3296C24C peer_handle = 0x80000068 [Code]...
I am considering to buy two RV180Ws and place them on two separate locations. But before buying I would like to make sure that the units meets my requirements. Lets call the locations A and B. I would like to connect location A with full network access to location B. But at the same time I would like to have that location B also gets full access to the network at location A.Besides this I would like to be able to connect to one of the networks from remote with my laptop.Preferably all connections should be made using IPSEC and not PPTP.I would like to know if it is possible to make such a configuration, and eventually if there is a smarter way to do e.g. only letting clients connect to location A or B and granting them access to all ressources at both location A and B from there.
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
I am trying to implement IPSec Authenticated Firewall Bypass on windows vista clients within my microsoft domain to avoid implementing numerous windows firewall port exceptions for each client.
This is working internally on our network, between services servers (i.e AV server), and desktop clients. However i am having a problem when the clients are remotly accessing the domain via the VPN client.I have open traffic ports (IKE-UDP500, ESP - IP Prot 50, AH - IP Prot 51) bidirectionally between the remote vpn clients subnet and the services servers, however when the endpoints initiate traffic to the services server, the IKE traffic is unencrypted?
I have a problem to configure a IPSEC VPN on the SA520W ( 1.0.39) with Cisco VPN Client (5.0.05.290). In the logs are following error:
ERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.x
A customer of mine has two RV082 in different locations. The "main" router is providing a gateway-to-gateway VPN tunnel, and is also used by a few road warriors for VPN access. We've had some issues with the "main" router lately, so we've decided to exchange it for a brand new device (v3). The old RV082 was a hardware revision v2 device, so I had to manually rebuild the config on the new router. The new router is working fine so far - connectivity and gateway-to-gateway VPN are fine. IPsec Client VPN, however, doesn't work at all. The config of the new router is identical to the config of the old one, IPsec Client VPN used to work fine on the old router.
The router is running the latest firmware (v4.0.4.02-tm). I've been trying to make IPsec VPN work with "QuickVPNplus ver: 1.0.6" and the "Cisco QuickVPN Client v1.4.2.1". From what I understand, both programs first connect to the routers external IP and download some sort of VPN config file. The info in that file is then used to create the actual connection. The problem is that the config file is invalid. It contains HTML code instead of config data. This is the code: "<HTML><HEAD><meta http-equiv="refresh" content="0; URL=/cgi-bin/welcome.cgi"></HEAD><BODY></BODY></HTML>". The URL is the same I see when logging in to the admin interface of the router. The Cisco client tells me in its "wget_error.txt": "rwConnStart message=All 1 wget requests did not return a valid vpnserver.conf". Both clients connect to the router fine, and the config download itself is working - only the returned data is invalid.
I've already tried lots of stuff to make the problem go away - enabling/disabling the firewall, VPN passthrough options, and other things. I'm beginning to think that there may be a bug in the firmware I'm using, or that the way Client VPN works has changed in a way that makes connecting with a client implementing the "old" method impossible. By the way, PPTP is working fine, so we're using it as a temporary workaround. My client, however, isn't happy with this workaround - he bought a relatively expensive router so he can make use of its advanced features, after all.
I have been working on trying to get an IPAD using the built in VPN client to connect to an ASA5510 version 8.2(5). I have attached the debug from where I have gotten so far. Phase 1 is failing somewhere but the messages aren't real clear or at leat not to me. The ASA is acting as the local CA for the certificate. I inherited the config from another guy as he couldn't get it working and I have made some progress but still not luck in getting the tunnel to just come up. Access to resources will be next but I'd like to just see the ipad show connected.
Looking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?
I've just purchased a SRP527w router and loaded the new firmware which includes the 5 client VPN server function.
The function works great with my iPhone as a client, but I've been unable to make a connection from my Windows 7 laptop, as the built in VPN configuration doesn't have anywhere to put the group name.
Is there a VPN client, or is there some way to get the Windows 7 native VPN configuration to work?
Is there a safe way to use the Cisco VPN Client (V5.x) and Cisco Quick VPN (V1.4.1.2) on the same Windows PC? I need to access my office RVS4000 and my customer's PIX 506 from the same laptop (but not at the same time).
Perhaps I should be asking "Is there a single Windows VPN client that works with both the Cisco RVS4000 and Cisco PIX 506? I have seen these questions asked on various forums but have yet to see a definitive answer.
I have a Cisco RV082 and can successfully connect with the Cisco QuickVPN Client, 1.4.2.1. However, after 1 to 5 minutes I see the Windows 7 bluescreen indicating that the system has halted due to a problem with a driver. I have installed the latest Windows updates and reinstalled the client.
The bluescreen only occurs if I use the Cisco QuickVPN Client.
I just got my first WRVS4400N v2.Nothing has changed, the definition of small business means there are USUALLY one office, and several people runs around thus the need of a VPN server sitting at the home office Router. I think most of us small business operators had wished for a connection away from office, NO REMOTE GROUPS, just clients on phone, or laptop. Using this connection to get to some files which isn't sitting in the cloud, or perhaps using it to hop over firewall restrictions that some overseas countries had imposed.
What you should have is a setting for Stand-alone VPN server, NOT Router to Router.. What you should have is feature that generates the various psk for different platforms. What you should have is made things simple, instead of these magicabbage which goes no where for the small businesses.Through out this thread the original poster is presenting the same problem, he and I don't have a Remote Group router to enter an IP address, tell us to use the QuikVPN client DON'T work, the Server isn't UP to begin with!Moreover, the VPN client installer on the this new v2 runs only in Win 2000 or XP??? What the (*&^! Doesn't seem like a large business like Cisco should have in their boxes.
I recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
I have a linksys 3200 router and i am wondering what all External USB HDD work with it. I have a WD 1 TB but it doesn't seem to work with it. I know that with the latest Firmware the router supports drives upto 3 TB so i know my capacity is not the issue but rather it seems that the drive itself just isn't recognized at all.
I installed the RV180W yesterday and decided to play with it a bit today. I got stuck on the firmware update. Tried different browsers on different PC's. Tried going to 1.0.1.9 first. I have the "reset all configurations" button checked. After looking through the posts here I'm not sure this firmware will even fix my next few problems(port forwarding etc). Is there a trick with this device?
I'm trying to make the VPN connection between two routers CISCO RV180w.I performed the basic configuration in cisco "server". I did the same in cisco "client".The following configuration and logs, do not know what to do ...
SERVER CONFIGURATION: IKE Policy Configuration: VPN Policy Configuration: CLIENT CONFIGURATION:
We have installed a fiber internet access and have the ONT from the provider already installed.We're trying to use the RV180W to use this internet connection. [code] So I need to configure the router with the .36 static IP on the WAN, and using the .37 gateway and the provided DNS servers. I also need that this WAN is tagged with VLAN ID 20. I'm only able to set VLAN ID on the LAN ports via the admin interface.
I am struggling to configure my new RV180w router to accept a VPN connection from my Apple computers.
I wish to use IPSec with Group and Pre-Shared Key authentication. The RV180 has just replaced my 800 series ADSL router and I want my remote clients to be able to connect using either the VPN client capability built into the OS X operating system or the Cisco VPN Client software installed on their Macs.
So far, using the RV180's web setup screens, I have created a VPN Policy and a corresponding IKE Policy was created as well. I couldn't see anywhere to include the 'Group' name. I have created a user but wasn't sure of which Protocol to use so I am trying XAUTH.
At the client end some people are connecting using Cisco's VPN Client software Download Software - Cisco Systems
Some people, with OS X 10.6 and above, are using the Mac OS X network built-in VPN client.
We all connected without a problem to the previous 800 series router using IPSec with Group authentication and Pre-Shared key.
i've installed the new firmware on my router and now the UC is showing 100% all the time. I've tried to factory reset it, it's doing the same thing. If I downgrade to previous firmware, it goes back to normal . I've only 1 PC in my network (test lab), so no big traffic here. is it a bug ?
I just recently switched from the WRVS4400N to the RV180W. I have 4 VLANs, and I want VLANs 1, 2, 3 to communciate freely, but I DONT want VLAN 4 to communicate with anybody, just Internet access. On the WRVS4400N, I was able to do this using the Firewall > IP Based ACL. I notcied that the RV180W, does not have such an option. I am sure there is something I am missing, I just cant find out how to isolate VLAN 4.
we've changed our rv042 for a rv180w and now when I try to upload files to my ftp server (vsftpd under centos) it get stuck at 100%.I've changed my ftp server to proftpd instead of vsftpd and everything's ok.but vsftpd isn't the problem since i was able to upload with my rv042 without any problems.so i guess there's a problem with the rv180w security.i've already disable stealth mode and it's doing the same thing when i try to upload to the same server but through the vpn tunnel, everything's ok.So it's really in the rv180w lan->wan routing
I am located in UK which uses PPoA for ADSL broadband. I use a DrayTek Vigor120 ADSL2 Modem to act as an ADSL bridge and PPoA to PPPoE converter. This passes the ADSL authentication requirement (and subsequent single static IP address) to the Cisco Small Business RV180W sitting behind the Draytek. However, the RV180 (Firmware Version 1.0.0.30) cannot form the PPPoE connection. I have tested the modem, adsl username and password by creating a PPPoE interface on my computer and connecting this directly to the Draytek modem. The computer receives the expected IP address and I can ping remote public IPs. I have entered the username and password into the PPPoE profile,
Authentication type: CHAP (confirmed by ISP but I have also tried all other options just in case). Connection Type: Keep Connected. MTU Size: 1400 (also tried default, which worked OK on computer interface). MAC Address Source: Use Default (I have successfully used combined modem/router so a "fixed" MAC address is not required).
