Can't Reach Router / Internet Anymore
Sep 1, 2012
I have got a problem with my LAN connection. I can't connect to the internet anymore and I can't reach my router. I rebooted my router several times, but that didn't work. I thought my network adapter was broken, so I bought a new one and reinstalled the driver, but it did not work. My router does recognize my computer though. When I tried to boot in safe mode with network opportunities, I was able to connect with my router and internet. I can't use System Restore as I don't have any restore points.
View 10 Replies
ADVERTISEMENT
Aug 16, 2012
Just got a brand new router this morning. Hooked it up to the modem, called Bright House and had it set to bridge mode, set up our wireless range extender and everything was fineMy dad's mac laptop was able to connect as well as my win7 desktop. When my brother tries to connect using his win7 laptop, though, he can connect to the router but not to the internet. He keeps getting limited access. He was able to connect and use a neighbor's wireless (but obviously we don't want to be doing that) so we know it's at least working
View 5 Replies
View Related
Mar 29, 2013
i have just purchased my wrt54gl two weeks ago. Setup was a breeze and it worked flawlessly until this morning when i noticed i had no internet. The ethernet light on my modem, when connected to router (Ubee 10C035 3.0/Comcast ISP) will blink 2-3 times then stop for a half second then blink 2-3 times and so on. Plugged ethernet cable from pc directly into modem and my desktop connected to the 'net fine and light was blinking normally(constantly) again. A few power cycles/reset of the Router to defaults but no luck.
View 3 Replies
View Related
May 13, 2013
Region : Philippines
Model : TL-MR3220
Hardware Version : V1
Firmware Version :
ISP : Smart Bro
Today my router stops working. There is no internet on wifi even on lan. I thought my ISP is the problem but when I plugged in the wan cable to my laptop there's an internet. I tried to switch off the router and when I turned it on, there's an internet for about 15 seconds then after that there's no internet again. I also restore the router to its default setting but it doesn't solve the problem. This is the first time it happens to my router. I'm not using static ip address
View 1 Replies
View Related
Sep 7, 2010
can't find my internet connection anymore. I have the wrt110. when I click the little computer in the corner on my computer to see where I'm connected my connection isn't there and I have to log onto someone elses unsecured network
View 9 Replies
View Related
Dec 20, 2012
I am trying to setup a remote PC over a wireless access Point/Bridge to our FIOS router. Pic of setup is shown below. Everything is connected, there are no errors or security warnings shown in the ActionTec MI424 router. The RemotePC IP shows up as an Active Ethernet client in the Router config app. Moreover, I can run the connectivity test from the router app to the RemotePC and it passes that, and I can PING from the RemotePC to the Router. Yet I cannot reach the Internet from a Browser on the RemotePC (192.168.1.75). I am using (2) DLINK DAP-1522 Access Point/Bridge units and they have worked as expected. I set the Router log to list any blocked IP traffic as well, and it does not show anything being blocked from the RemotePC (192.168.1.75). So why can't I reach the Internet from the RemotePC? Seems like a gateway problem or I need to make some config changes in the Router.
View 2 Replies
View Related
Jun 4, 2012
Since some days we have a ASA5510, we connected it on a Windows Vista Laptop via ethernet cable (using at the back of the router the mgtm slot) and connect it on the network slot on the laptop. Laptop is getting IP addresses automatically.
Now we tried to reach the router in the Internet Explorer using: http://192.168.1.1, but we could not reach this site. When I try to ping the router via cmd and typing ping 192.168.1.1 I get answers.
For us it is very important to change the IP address of the router, as he will be used in a network with 10.xxx.xxx.xx addresses.
View 2 Replies
View Related
Oct 2, 2012
I bought an ASUS P8Z77-V motherboard, an i5 3570K and a Corsair Vengeance 4GB card a month ago. I built it with a Radeon HD 5670 graphic card, CoolerMaster 500W, a Sony lightscribe DVDRW unit and an old HD 500GB. The PSUs fan stopped working 3 weeks ago and I didnt notice this. While playing games the computer shut down, and I quickly opened the case. The PSU was hot and I could smell burned plastic. A week after I randomly tried to start the computer and guess what!? IT WORKS! Then I realised that only the fan was broken. I took the PSU and fan appart and lubricated the fan. It spins like a charm but I think I lost a piece of it and now its loud as hell but it works. I thougt this story might have something to do with the issue.
THE ISSUE: My internet has been working like a charm untill a week ago. A week ago the LAN or wired connection stopped working. I had to disable LAN adapter in BIOS else it would try to connect forever and I couldnt disable it in Windows. I didnt bother to solve it since my motherboard has a Wireless adaptor, so I just connected wirelessly. Today the wireless stopped working. I figured out that I might have goten a virus? I formated the disk and reinstalled WIN7 x64. I install the drivers, and the wireless and LAN still dont work. I reinstall WIN7 once again. Still nothing. I remember that I have to set the IP adress myself. So I go to Wireless adptor - preferences - IPV4 - type the stuff in, and when trying to close the window it freezes. After closing it in task manager a message "An unexpected error has occured" appears. I have to close Explorer.exe too and then after 2 attempts I get to close the window and save normally, but still no connection.
View 1 Replies
View Related
Jun 6, 2012
I am having a really important/big problem, 2weeks ago i try to upload in my deviantart,facebook,tumblr,blog etc..it worked great but on 1st june i got the upload problem.It take infinite time to upload 800kb.
I am using wireless internet. My isp name is tata photon+ LINK OF MY ISP
View 4 Replies
View Related
Jun 5, 2011
We have a VPN setup for a customer between our shop and their shop 2.5 hours away. This is a Cisco 871.We had Verizon and the connection worked (still does) great! We had to switch providers as they sold to Frontier and were going to change our IPs anyways so why not switch to a faster provider instead.We switched to Charter. I have ZERO, NADA, ZILTCH knowledge of Cisco and I plan to keep it that was as they are way more complicated then they should be. Ill stay with my Sonicwall.....Anyways.... I took the config and did a find and replace for all the IP's, Gateways, DNS etc....I blasted that into the router and it took right off and connected up the VPN in a matter of 2 minutes. I was estatic as I knew I was going to sleep good that night not worrying about it..............Untill the next day at 11 am when I get a phone call from work saying the connection was down.
I go and realize that the router cant see the outside world anymore, therefor was obviously not going to see the peer IP address. I was dumbfounded!. To make a long story short I tried reconfiging therouter with the same file. I even redid the find and replace and resaved it to no avail. Still no go, no internet. All the proper IPs, Gateways and DNS numbers are where they should be. To test that its the config and/or something to far above me. I re configed the router with the old config and hooked it back up to verizon, it took right off and reestablished the VPN and was working.
View 6 Replies
View Related
Dec 30, 2011
I never had any problems getting on the internet before, now I can't connect. It says my signal is excellent, and that its acquiring network address. I have tried repairing the connection, but it doesn't do anything. I also get a box at startup that says:
Error loading C:documents and settingsall users application dataWindowsserviceManager.dll. The specified module could not be found.
View 11 Replies
View Related
Oct 7, 2012
I have had my Acer windows vista laptop for about 3 years but it has only been this past year it has stopped connecting to the internet, which means i have to use a cable to access the internet, but im pretty sure its not the ruter because my brothers laptop connects fine, and his is a very old laptop!
View 3 Replies
View Related
Jul 11, 2012
I was connected to a wifi-spot for two weeks and it worked all fine. Since a few days ago the owner of the spot changed the password and since then I can't connect to my internet anymore. I'm 100% sure that I have the right password but still when I try to connect it shows a yellow triangle with a black "!" on top of it, saying "Limited or no internet connectivity"[CODE]
View 1 Replies
View Related
Sep 30, 2011
I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
View 18 Replies
View Related
Mar 31, 2011
I have a Dell 1750 inspiron T4300W7 laptop which worked fine until one night whilst connected to internet via a 3 dongle it just cut off. I have used the dongle many times on this laptop without issue and the dongle still works on my other laptop fine. The Dell laptop now wont connect via any internet method ie wireless or dial up connection, it just says No network access. I run a diagnose and a message said ip address not configured.
View 1 Replies
View Related
May 30, 2011
Att says they are giving us 3mb/sec but we get 300kbps and speed tests from anywhere say we get 2.5 to 2.9 mb/sec yet even on unlimited bandwidth downloads(like torrents) with thousands of seeds connected and a few peers they never get faster than 340kb/sec.
View 9 Replies
View Related
Nov 30, 2012
I have been at this for the past few hours now. I just cannot get this device to pass through traffic to the internet. Here is the basic topology:
Default Gateway (ISP): 208.118.125.129/29
IP of outside int (e0/0): 208.118.125.130/29
ip of inside int (e0/1): 10.1.1.1/24
igniteCSGfw(config)# sho run
: Saved
:
ASA Version 8.0(4)
[Code].....
View 3 Replies
View Related
Mar 6, 2012
I have been configuring a cisco ASA 5520, everything is working fine but when i create an ACL:
-access-list OUT extended permit ip 172.16.x.x 255.255.255.0 any
-access-group OUT out interface outside
i added ports like www or 443 and it is not working to Internet access a router is before to my firewall connected to my headquater, i can see my private networks but i cannot able to reach Internet access,
View 3 Replies
View Related
Oct 10, 2011
We had setup a wired/wireless LAN using Cisco 881W router for one of our client. Wired lan works OK but we have issues with wireless. Users on wireless LAN can connect to the wireless network, but cannot browse the Internet. The wifi network does not give out an ip address to the client so client cannot get to the default gateway and Internet. Not sure what part of config does not work.
##### sh runn #####
881WiFi#sh run
Building configuration...
[Code].....
View 10 Replies
View Related
May 20, 2013
PCs --> SG500(4 vlans) --> rv042 --> Internet..vlan 1 is able to reach the internet..vlan 2-4 cannot reach the internet, but can reach vlan 1.
View 2 Replies
View Related
Apr 11, 2011
I'm having trouble setting up local LAN (reach inside network when VPN connected) and Internet access (reach internet when VPN connected) for my VPN CLients when they are connected to my VPN, They can connect, no problem there, but I can't reach any resources when connected. My pings time out, both to my inside network and to public ip adresses, the only thing I'm able to ping is my ASA (172.16.30.1), and I don't se any routes under "Status/Statistics/Route Details" in my cisco VPN Client (when connected).
Here's my config
ASA Version 8.0(3) !hostname KardesASAdomain-name default.domain.invalidenable password XXXX encryptednames!interface Vlan1 nameif inside security-level 100 ip address 172.16.30.1 255.255.255.0 !interface Vlan10
[Code]....
View 14 Replies
View Related
Feb 1, 2012
So, I currently have a desktop and 3 laptops connected wireless to the router in my home, yet the GATEWAY laptop no longer connects wireless. I have to use the wire in order to connect to the internet and it's starting to become annoying. I had to restore the Gateway laptop back to Windows XP from Windows 7 due to a LARGE amount of issues with Windows 7. I'm in need of this laptop in order to complete my paper work.
[code]...
View 4 Replies
View Related
Jan 9, 2013
I have been using d link routers for a very long time. However, recently I have a problem with one of my dlink router..
Basically I have a Wireless N 150 Home Router (DIR-600 B2). I managed to reset and login to the router at http://192.168.0.1. I tried to made some configuration (disabling DHCP, some stuff, basically I was trying to configure this router as Wireless Repeater to connect to another room downstairs).
So it didn't connect so I do a reset (hold a pen for 20+ seconds at the reset button) and now I cant login to the router at http://192.168.0.1..
View 4 Replies
View Related
Apr 15, 2012
for the last 5 days or so, my internet was acting weird, disconnecting every 20 mins or so, i had an old linksys router, no clue on the modem, but all of it's about 7 years old, i got a replacement, Motorola SBG6580, my connection is somewhat better, but my ISP says they can't ping my router/modem
View 1 Replies
View Related
Jan 1, 2013
I can't connect with my D-Link router 4300 to the modem. It's like my router doesn't recognize the internet connection of my modem because there is no available connection at all, for every single PC in my home ! When I connect a cable to my PC, it works. I can't see the problem because I can't even connect to http://192.168.0.1/. I tried many variations but nothing. It all started because I changed the WPA security to WPA2. Then it restarted my router and nothing worked after. I tried several times to reset my router with the reset button, but nothingHere is the ipconfig[CODE]
View 1 Replies
View Related
Jul 18, 2011
Comcast sent out a new modem a few days ago. The reason for this was our internet had gone out for a while, they came in and said our modem was fried. I have internet access by directly wiring from the modem to my computer.My router doesn't work anymore. I have a local network, but no internet access. I'm using a Linksys WRT54G, and I don't really know what to do.As far as I remember, setting everything to defaults and factory settings was how I set up my router in the first place and it just worked.
View 11 Replies
View Related
Dec 2, 2011
My entire floor receives wifi from a D-Link router box. For the first 4 months, my laptop was able to find and connect to our wifi fine. Last night the internet crashed. All of my German housemates have internet again, but my laptop does not show the network anymore. My wireless card picks up all the other signals in range, but not our router's. I can only get internet with an ethernet cable.
View 1 Replies
View Related
Jan 4, 2012
A couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
View 5 Replies
View Related
Jan 8, 2012
The linksys E3000 Could really use a firmware update.. the last one was 12/01/2010Ver.1.0.04 (build 6)
View 6 Replies
View Related
Feb 19, 2012
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
View 9 Replies
View Related
Mar 27, 2011
I have two desktop computers upstairs.The main pc has the Linksys G Router and the other pc is wireless with a network adapter. All works fine here.Downstairs and on the other side of the house, I use my laptop which is wireless to the network. I also have a 46" hidef tv hooked up to a blu ray player and also connected to the network with a wireless adapter. I use Netflix to stream movies and seem to be having a problem with the signal in this room, both on the tv and my laptop. I sometimes only have 2 bars on my laptop and frequently get disconnected to the internet. When I am streaming movies or tv series, I get frequent stops and starts.
I am guessing that the signal is just not strong enough to reach this far from the router. Would switching to an N router be better for streaming? Would another G router downstairs solve my problem?
View 4 Replies
View Related
Nov 28, 2012
192.168.100.1 is how I access my modem using the 4100, but since buying EA6500 I can no longer find the config screen. connect to there modem from the EA6500?
View 7 Replies
View Related
Jul 30, 2012
I have an E4200. Since yesterday morning I can't connect to a certain website. This happened all of a sudden. I am able to connect to any other website I try to access, but this particular one won't connect at all anymore. If I unplug the router and connect directly from my computer to my modem, then I can access it with no problem. I haven't done anything to the router. Was there some sort of update yesterday. The website I can't connect to is [URL]
View 1 Replies
View Related
