I have an E4200. Since yesterday morning I can't connect to a certain website. This happened all of a sudden. I am able to connect to any other website I try to access, but this particular one won't connect at all anymore. If I unplug the router and connect directly from my computer to my modem, then I can access it with no problem. I haven't done anything to the router. Was there some sort of update yesterday. The website I can't connect to is [URL]
I have an E4200 (v1) with the latest firmware. For some reason, the E4200 does not allow me to conenct to certain websites. This is true for wired or wireless connections.To test, I connected a wired PC directly to my cable modem and was able to connect to all websites fine. I also tried an old D-Link router I had on hand and was able to connect to all sites fine. Went back to the E4200 and was blocked. I re-loaded the firmware and same results.
I was having a problem viewing the {Url } but it has worked for the past year. I just purchased a new router E4200 and thought that would reserve the issue. When I first installed it I could get on the site and then about 10 minutes later when I restarted my MacBook I could no longer get on the site. I can't get on it on my MacBook, or iPad but I can when I'm on 3G on my phone.
i just upgraded from the E4200 to the EA6500. i have a few websites on one of my machines, which i can access from outside my network no problem, but when i try to access it from inside the network, firefox gives the message "the connection to the server was reset while the page was loading". i did not have this problem with the E4200.
i have just purchased my wrt54gl two weeks ago. Setup was a breeze and it worked flawlessly until this morning when i noticed i had no internet. The ethernet light on my modem, when connected to router (Ubee 10C035 3.0/Comcast ISP) will blink 2-3 times then stop for a half second then blink 2-3 times and so on. Plugged ethernet cable from pc directly into modem and my desktop connected to the 'net fine and light was blinking normally(constantly) again. A few power cycles/reset of the Router to defaults but no luck.
I can't open the Ryanair website any more, everything else is working properly. This happened during spanish general strike when their website may have crashed, but since then it wont open. I am using Google chrome.
I own an E1000. It is hooked up to a Motorola cable modem via Comcast. I have a personal website sohebvahora.com (still under construction) where I use cpanel to administer it. I somehow lost all connectivity to my website midday and have not been able to connect back to it in a few days. Every other site I have gone to works except mine. It doesn't make sense.Also, I tried connecting my laptop directly to the Motorola modem and my personal site loads, so it has to be the router. I have tried different devices connected to the router as well, like my ipad, iphone, and other laptops, but the website doesnt load on them either
I can't connect to the public weater site NOAA.gov, and weather.gov, but have no problem connecting to any other sites, private of public.WRT54Gv6 wireless with v1.02.08 (Oct 5, 2009) firmware..the latest.3 devices, desktop, laptop, and iPad......none of which can connect to NOAA or weather.gov Government websites are up when I tried to connect.I've connected to these sites for years, and as recently as yesterday.Linksys BEFCMU10 cable modem. This blows my mind, since the 3 device all have different OS's, browsers, AV software. The only thing in common in the network is the modem and wireless router. Why only the two .gov sites cannot connect?
I had the website filter ON and it was working very well to block a few websites on a schedule. And after a few month, it doesn't work any more. While it is possible that I scewed up the setting , I have tried so many settings.
So:DIR655 fw 1.32NA,hw A3,"Enable access control" is on with the desktop MAC address (used copy this MAC)(I have also tried my laptop MAC),web site filter is set to "deny",the router time is set using NTP dlink server,
I have a blog and website hosted by X9 Hosting. I am unable to connect to cPanel, the website, the blog, or and X9 sites.This began when saving a WordPress article in the blog. The save hung and then all connectivity through the router was lost.When using the modem (wired) I can visit the above sites. what do I need to do to gain wireless connectivity back?
So, I currently have a desktop and 3 laptops connected wireless to the router in my home, yet the GATEWAY laptop no longer connects wireless. I have to use the wire in order to connect to the internet and it's starting to become annoying. I had to restore the Gateway laptop back to Windows XP from Windows 7 due to a LARGE amount of issues with Windows 7. I'm in need of this laptop in order to complete my paper work.
I just connected my new E4200 router, it worked fine until it recommended updating, as soon as it connected to do this, the power light started blinking every second and it will no longer respond. Support has not facilitate.
I've had this router for just over a year now so the warranty is out and it just so happened to stop functioning last night. I'm fairly decent in the router world since I am studying for my CCNA, so I have tried just about anything imaginable. I woke up this morning with no connection, checked the modem, then the router. The router was powered on, but the up/downstream lights were not doing a thing. The modem is not the issue (I am hardwired as of now). I have tried both resets, including unplugging the device, and still can't get a response out of it. The logo light will turn straight on (no fad in and out like it's suppose to) and then it does absolutely nothing. I have never encountered this sort of problem on a home router before. I can't login to the router either.
I have 2 E4200's . One is connected to my ADSL Modem as DHCP and the other one is Bridged to the DHCP. I'm trying to connect to my E4200 that is set as Bridged. I am able to connect to my E4200 that is set as DHCP, but I cannot connect to the E4200 that is connected to that DHCP as Bridged.
How can I connect to that bridged E4200 because I want to upgrade the Firmware of the Bridged E4200?.
Been having problems connecting an old WGA54G v2 (firmware 1.16, March 29, 2005) to a new E4200 v2 (firmware 2.0.36) via WPA. I can get the two to connect using no encryption or WEP but not WPA. Using WEP is not an option for me,E4200 v2 wireless settings:
1. 5GHz broadcast is off, 2.4 GHz is on. 2. Network Mode - Mixed 3. Security Mode - WPA2/WPA Mixed Mode 4. Channel Width - Auto 5. Channel - Auto 6. Guest Access broadcast is off
WGA54G v2 settings:
1. SSID - same as router 2. Network type - Infrastructure 3. Security - enabled 4. Pre-shared key - same as router 5. Encryption - WPA Pre-shared Key, TKIP (tried AES, but still no connection)
Also, tried different WPA network modes on the router (Mixed, WPA personal, WPA2 personal etc.) to no avail. Switched between mixed, B and G network modes as well on e4200 v2 but still no connection. My guess now is that the WPA on the gaming adapter and the WPA on the router are just not compatible, as completely asinine as that sounds. Thought about updating firmware on the WGA54G v2 but checked in the download section here and the last firmware available is 1.13 (appears older than my 1.16, even though the 1.13 release date listed is a month after my 1.16).
I have this E4200 for about 3 months and allways has been used as an wireless router. Today i wanted to connect 2 wired computers to it via lan and whatever i do dosnt connect. Dosnt even let me acces the 192.168.1.1 page to router settings.I am on firmware 1.0.02, i also did a full reset and then did set up with cisco connect, did try that thing with the cisco usb connect and still no joy with the LAN conection.
One comp uses win 7 the other is on win xp. I can connect both comps succesfully to other router via the gigabit ports but not to this one.
On the 2.4ghz side, I'm set up on the cleanest channel (per inssider) which is 6, channel width is auto (although I've tried it fixed at 20 also), N-only, and security is WPA2 personal. WMM support is enabled. I'm running firmware 1.0.02 The laptops continually stay around 72mpbs, occasionally jumping to numbers in the 100 range... twice I saw it actually hit 144. Inssider shows the max rate as 144, while other N networks in range are as high as 270. I'm sitting right next to the router with 5 bars -- why is the max rate 144? Why won't it run at 300?
So I purchased a Linksys E4200 a couple weeks ago from Best Buy (got the $149 price) and finally got around to setting it up last Thursday. Before I get to my problem, I am happy to say that I have not experienced the "blinking light" syndrome that seems to plauge a number of other owners. In fact, the E4200 is everything I hoped it would be ... except for one problem. I cannot get my sister's Acer Aspire One netbook to connect to it.
It's really strange actually; the netbook picks up the 2.4GHz SSID fine (it's set to mixed mode) and upon selecting it and I input the WPA2-Personal password no problem. Then, it takes forever to finally aquire a network address, like at least 3 full minutes (usually this process takes a few seconds). After that, it tells me it is connected to the network with excellent signal strength. Except, despite it saying it's connected, the Internet does not work at all. If I got into the details of the wireless adapter, it tells me that the router/network failed to give the adapter a network address.
after setting up my e4200, I am no longer able to connect to Steam, I instantly get a connection error. I'm told it should work fine with UPNP, and I've even forwarded the proper ports just in case, but I cannot connect. I have latest firmware. Hoping someone else out there has same router and uses Steam.
1. I will be getting a e4200 on Thursday and was wondering if there is any advantage/disadvantage to using the Cisco Connect or just following instructions for manual setup using the web (I did it that way on my last router 6 years ago but was just following a script).?
2. Can I change things using the web after setting up using Cisco Connect or do I have to always use it:?
3. Finally after I set the router up can I just set up other computers in the house as I do now (just plug them in using wire or search for wireless and put in password)?
I've switched over from a d-link dir-655 router to the v1 4200. I've been playing around with the 4200 and trying to get it connected to my tv all night long. I have two laptops and two iphones connecting with no issues. I cannot for the life of me get the tv (GT30) to work. It picks up three signals, the 2.4 signal, the 5 signal and the guest signal. The only one that will even connect to the internet is the guest signal. When I run the connection test, however it will not connect to the vierra connect server. I've tried setting it up manually, and anything else that seems obvious. I had no issue with the dlink router at all.
Just bought E4200-V2 and happy with the performance, except one thing.After several hours, I could not connect to the router manager both from "Cisco Connect" nor browser.I could resolve this by turn off the router and turn on again, but the same problem will be back after several hours.I tried to reset the router (reset 30 and reset 30/30/30) several times but have no luck.
I've noticed that my 192.168.1.1 login console was slow loading up on my E4200 V1. The router functioned just fine(wireless and wired). These past few days I tried to log in to set some DNS settings and I cannot access 192.168.1.1.I have tried via wireless and wired. The router powers on still seems to function but won't allow me to load up the admin console page.To my last resort, I held in the tiny reset button and the router seems to have went back to it's default settings (SSID = Cisco#####) but I cannot connect to it. what I can try to get back into the management window.I was able to manage everything from my laptop about a month ago or so, but now I can't do anything.
I have set up my WAG320N with my E4200v1 successfully. The problem is that my laptops can't connect through WiFi with the E4200 router, but only with the WAG320N (wireless). Since it is the first time I set up a network alone I possible have made mistakes and that's why I can't connect to my router wirelessly. My desktop pc will successfully connect to both of my routers (wired)! My devices won't (DS,Laptops). I have WEP security in my WAG320N (because this is the only one my DS card can connect to) and in my E4200 I want to use WAP2 to connect my 2 laptops. I have made nothing more than setting them up and both of my evices are new.
It is for home use, both of my devices are updated to their latest firmware and the laptops won't identify the problem and will ask to restart the router. (I did many restarts both on my routers, PC, laptops)
A couple of days ago I noticed my download speed (from my own webserver) has slowed down. I checked my wireless connection and saw that the radiotype was now 802.11g instead of 802.11n, what is always has been. I looked at the Wireless configuration in the router's webbased config panel, but the only things listed there are "Disabled", "Mixed", "Wireless-G Only" and "Wireless-B Only". A scratched my head a bit, wondering wether or not I really bought an N router or just a G router. But IIRC I really bought an N router. It said so on the bill. Also, when I check the user manual, page 14 says I should be able to select "Wireless-N Only".
I got the new E4200 router as I had issues with my old router. I was able to DMZ my console with the old router. But with my new router my xbox IP has changed and I want to know which numbers to use and how to DMZ my Xbox with Cisco Connect.
After I updated my E4200 V1 with the 1.0.04 update I am unable to connect my WET610N to it with 802.11N. I can connect fine with 802.11G. I tried the Site Survey method of pairing them as well as manual. When it fails it goes through the minute timeout of trying and then Link Status is disconnected. I have anything from phones to laptops connect to the E4200 with wireless N, its just the WET610N that doesnt want to pair.
I'm using E4200 with latest 1.0.02 firmware and found I can not connect to VPN with my iPhone4 by WiFi.Googled a bit and found it's a common problem for Cisco routers when wireless devices can not connect to VPN but wired ones connects with no problems.\
I have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
Connecting E4200 media server (external hard drive connected to USB in router) to PS3.mapped External HD to media server folder. and enabled UPnP Media Server. after trying all options I can't see media server in PS3.
