I'm trying to reach Celebs4.UsThe first time I tried (earlier today), I was able to access, but when I clicked on one of the images I recieved a "The connection has timed out" error. I have not been able to open the site at all since that very first time.I have done the following:- tested it in both FF and IE- run tracert (seems like the problem is on the site's server end, but everyone else is able to connect fine)- flushdns- clear cachemy tracert: :: pokIt
I am trying to access [URL] with a Linksys E3000 router. A few days ago it was working fine, and between then and now I made no changes to my network, it just stopped working one day, I assumed the website was down but it turns out that I am able to access the website fine on other networks or via proxies. I also hooked up my computer directly to my modem and I was able to connect to the website fine, but when I try my wired connection to the router I am unable to connect, I have tried Google DNS without success. I know this is a problem with my router, not my modem or computer or ISP.
for the last 5 days or so, my internet was acting weird, disconnecting every 20 mins or so, i had an old linksys router, no clue on the modem, but all of it's about 7 years old, i got a replacement, Motorola SBG6580, my connection is somewhat better, but my ISP says they can't ping my router/modem
I am facing the following problem. SmartPhone is connected WiFi hotspot. Suppose SmartPhone ip is 10.0.2.2 and hotspot ip is 10.140.13.12. I am able to send data from smartphone to a server(over internet) which has static ip and sender details in server are hotspot ip. Problem is sending data from server back to smartphone. Tried sending to 10.0.2.2(smartphone) from server but packets are not received.
I have got a problem with my LAN connection. I can't connect to the internet anymore and I can't reach my router. I rebooted my router several times, but that didn't work. I thought my network adapter was broken, so I bought a new one and reinstalled the driver, but it did not work. My router does recognize my computer though. When I tried to boot in safe mode with network opportunities, I was able to connect with my router and internet. I can't use System Restore as I don't have any restore points.
I have two desktop computers upstairs.The main pc has the Linksys G Router and the other pc is wireless with a network adapter. All works fine here.Downstairs and on the other side of the house, I use my laptop which is wireless to the network. I also have a 46" hidef tv hooked up to a blu ray player and also connected to the network with a wireless adapter. I use Netflix to stream movies and seem to be having a problem with the signal in this room, both on the tv and my laptop. I sometimes only have 2 bars on my laptop and frequently get disconnected to the internet. When I am streaming movies or tv series, I get frequent stops and starts.
I am guessing that the signal is just not strong enough to reach this far from the router. Would switching to an N router be better for streaming? Would another G router downstairs solve my problem?
Just got a brand new router this morning. Hooked it up to the modem, called Bright House and had it set to bridge mode, set up our wireless range extender and everything was fineMy dad's mac laptop was able to connect as well as my win7 desktop. When my brother tries to connect using his win7 laptop, though, he can connect to the router but not to the internet. He keeps getting limited access. He was able to connect and use a neighbor's wireless (but obviously we don't want to be doing that) so we know it's at least working
I have a 2811 (running 12.4(15)XZ) with a WLCM (4.2.209.0).
I have reset the configurations on both. Set FE and WLCM IPs on the router and gave WLC Management and AP manager addresses. All + PC are on the same subnet. Router pings all addresses besides AP-manager(intended). WLC CLI cannot ping PC and PC cannot ping (nor http) to WLC. PC can however ping and telnet the router on both the FE and WLCM IPs.
I followed the guides on WLCM configuration, did I miss something?
How can I access the management IP and the web GUI?
2811 config:
Building configuration...
Current configuration : 1292 bytes ! version 12.4 service timestamps debug datetime msec
I've setup a SSL VPN to a ASA 5505 and can connect.
VPN network 192.168.2.0 /24 Inside Network 192.168.1.0 /24 Outside is connected to Router.
I am trying to RDP to a win server on the inside network but I cant get to it. Can not even ping 192.168.1.1 or (not sure if I could anyways) 192.168.2.1...
I added a ACL on the outside interface and then inside interface permit ip any any but still no ping or RDP...
New at VPN and have survived so far on cisco docs but this problem is evading me.
I have an ASA running 8.2(2).I am trying to get the network on the inside interface to be able to communicate through the outside interface and on to the internet.
since a few days I'm trying to solve a problem. I've successfully established an IPSec tunnel between two local LANs. In the main office I'm working with a ASA5510 CLI 8.4 and a static public IP address. The branches are using different Cisco 8xx routers and dynamic public IP address. The following picture shows the current configuration:As I mentioned an IPSec Tunnel between the main office "Intern"-LAN 192.168.1.0/24 and an outside LAN 10.10.0.0/24 is successfully established. Now there is a new intern "Admin"-LAN 192.168.2.0/24 at the main office. The users from the outside LAN 10.10.0.0/24 need the possibility to reach this new intern "Admin"-LAN.Can I simply route the traffic from 10.10.0.0/24 to 192.168.2.0/24 via the existing IPSec-Tunnel? Or need I a new IPSec tunnel between the outside 10.10.0.0/24 LAN and the new "Admin"-LAN 192.168.2.0/24?
I have a network of one router which servers both LAN and wifi, my laptop can only use wifi to connect but the range of the router doesn't reach the third floor. I need a way to either extend or create a second hot spot but I'm not sure whether to use a repeater, a hub or a switch? this is my first time dealing with a network
Goal: extend the reach of my WiFi to multiple floors with keeping in the basement the DSL modem - Actiontech M1000 and Actiontech W1000. I have a Linksys Access Point and Linksys Router. I was told by CenturyLink (only allowed support for Actiontech) that the modem would need to be put in bridge mod that would disable the Actiontech W1000. Whereas I want to keep access in the basement and add coverage to upstairs.
being able to config the Linksys(s) or using DD-WRT operating system?
i'm setting up vlan and inter-vlan routing in my lab. My vlan work well (routing between them and dhcp relay) on the LAN side of the ASA but they cannot reach internet trough the ASA.
Here my ASA settings :
Note : I know that the physical interface musn't have an @IP but my present network needs one to work. I'll fix this during my next tests.
We set up a 1941 Router with the Cisco Configuration Professional Tool. The VPN Tunnel works and i get an IP Adress from the pool. But i cant reach any devices in the VLAN10 Network. Do i forget anything ?
Here is the config from the Router:
version 15.1 parser view CCP_Monitor secret 5 $1$FnN7$Qr.mbJbPOuOH7Te6MD1.I0 commands configure include end
I have a (central) ASA5510 acting as a EasyVPN server and a number of (remote) ASA5505 as EasyVPN client. All the communication works fine between the different networks. The issu is the ASA itself. The remote ASA can ping the central ASA on it's internal IP-adress, but it can't ping any other resoruces at the central network. If I ping the DC at the central network from the remote ASA I get a deny in the central ASA with source address as the public IP-adress of the remote ASA and destination of the internal address of the DC. If I from the remote ASA do "ping inside ip-of-central-dc" it work's like a charm, but "ping ip-of-central-dc" dosen't work.
I have configured a Remote access vpn on pix 525 with 7.2(4) code. After getting connected (with ip address assigned from the pool) i am not able to reach any of the internal networks. [code]
I've setup a SSL VPN to a ASA 5505 and can connect.
VPN network 192.168.2.0 /24 Inside Network 192.168.1.0 /24 Outside is connected to Router.
I am trying to RDP to a win server on the inside network but I cant get to it. Can not even ping 192.168.1.1 or (not sure if I could anyways) 192.168.2.1...I can ping from the 192.168.1.0 net to 10.0.0.0 and 192.168.2.0 without issue but not the other way around....I added a ACL on the outside interface and then inside interface permit ip any any but still no ping or RDP...
I am able to reach VPN clients (Anyconnect) only from hosts directly connected to the ASA's inside interface subnet. However, hosts on other internal subnets (177.1.10.0 & 177.1.11.0) are unable to connect to clients on VPN. The ASA is running ver 8.4. [code]
I have remote access vpn setup and I can get connected with no issues. I assigned the vpn a pool of addresses from the end of my inside interface subnet. When connected I can ping any device on that subnet, I can also connect to my switch on the same subnet via my browser. I can not however access any device located in my dmz while connected. This is a new setup I'm testing but I need vpn user to be able to use rdp to connect to machines in the dmz.
This router support bridge mode, but i'm unable to configure it. There's no such option in the web configuration page, but the manual says that disabling nat activates automatic routing mode. Unfortunately all i get when i disable nat is to be unable to reach any wan address.
By watching the generated routing table on the wrp400 (when in NO nat mode) i see that 0.0.0.0 is correctly set up to use the external border router, but any incoming packet from the wrp400 lan port isn't routed there.
Also, i don't get any dhcp from the external router, this means the wrp400 is blocking it.
how to set up a bridge mode between wan and lan ports
Recently i bought a new printer: Epson SX620FW, I've tried many things, but I can't connect it wireless to my network. Ive downloaded and installed the latest drivers and software from the internet. My PC is connected with a cable to my wireless router. When I connect the printer with a cable to my router everything works perfectly. But I want to connect my printer wireless. On the printer I disconnect the cable. I followed the wireless wizard setup on the printer and I connect to my wireless router. This is confirmed by an ip adress on the printer. Also in the menu of my router I find the ip adres of my printer in the DHCP clients list. So far so good. But from my PC I can not find the printer in my network. I also cant ping my printers ipadres. When I connect the UTP cable to my printer again, I can ping the ip of my printer.
Att says they are giving us 3mb/sec but we get 300kbps and speed tests from anywhere say we get 2.5 to 2.9 mb/sec yet even on unlimited bandwidth downloads(like torrents) with thousands of seeds connected and a few peers they never get faster than 340kb/sec.
I'm having some troubles with SSLVPN connectivity. I've setup SSLVPN at one site and it works great with web access, file share, RDP plugin etc. at the local LAN on that site. But I also would like to reach another site (connected with an IPSEC tunnel). Is this possible? if it is, how do I do it?Both firewalls are ASA5505, one 8.31 and one 8.22 Just a note, it works to connect with IPSEC client and reach the remote site just fine.
I have a new EA4500 router and I cannot configure it to reach the 450 mbps that is supposed to get.
I have it configured as follows: Dual Band- 2,4 and 5 GHz 2,4 in 20MHz only - 5 GHz in 40 MHz only 2,4 Mixed - 5 Ghz only N WPA2 personal in both Channel - automatic (both)
I have checked that the 5 Ghz network can only use 4 channels: 36, 40, 44, 48. Where are the channels up to 100 (or more)? How to get all the power of the router?
I have a F5D8235-4 N+ router and I am trying to connect my Seagate Free Agent hard drive to the USB port on the router so that I can access it on all my network computers. When I first hooked it up, it worked. Now, the drive is lit up like it is working, and when I enter \192.168.2.1 I can see it, however my Windows 7 computer is unable to access it (even though this is the same computer that accessed it when I first hooked it up). The computer I am using is running Windows 7 and is connecting to the network wireless.
I have created a connection gateway-to-gateway between RV220W and RVL200, is doing without any problems.For example, I can ping the gateway on the other side. But when I connect trough RV220W QuickVPN (or PPTP) I can not reach the gateway (RVL200) or any host behind it.
I have a cisco 2851 router as the edge router, I have a 3750G and a 3560G switch and configured intervlan routing with four vlans, also connected to the switches a four servers and one has active directory and a dns server.i am able to ping from all te servers fine from different vlans and the servers are able to ping the edge router. the problem I am having is with DNS, in the edge router i have configured the isp's dns server address in ip name-server and i am able to reach the outside world.
the problem im having is the servers are not able to reach the outside, do i need to do something in the edge router to forward it to the 3750g or do i have to add my isp's dns servers on the 3750g with ip name-server.
I have DSL set up in a home network. I want it to be used in my barn. The signal won't reach wireless though. I have 2 older wireless routers not being used - Lynksys wrt54gx4. Can I add two of these in the path to the barn to extend the signal? I would put one in the back of the house and one halfway to the barn in the pool house. ZCan these routers connect wirelessly to the home network?
In one of my client location I have deployed one Cisco 3560X (core switch) and one SG-200-18 (access switch). I’ve configured three vlans (vlan 2, vlan 3 and management vlan 1), relevant trunking and I’ve connected two pc to the access switch to vlan 2 and 3 respectively. So far everything (including inter-vlan communication) works fine, except that I couldn’t reach the vlan 1 (management vlan) devices (access switch and core switch) from any pc which is connected to either vlan 2 or 3.
I’ve configured the “port VLAN membership” settings in SG-300 as follows,
Interface mode Administrative vlans Operational vlans GE 2 Access 2UP
An 1841 is conencted to the internet by DSL, it works fine. I have added it to the 10.98.8.x subnet off a 3750 switch.When I connect other devices to the same switch port, I can ping/browse to them fine, but when I connect the 1841 I can only ping it from the 3750, not another subnet connected to the same router. [code]
I have this strange problem with my Macbook pro, when I connect it to my cisco 2940 8 port switch then I can reach my ISP (websites eg. google.com) in like 2 minuttes, then something is happening on my router, because suddenly I can´t reach my ISP
This is what I have found out so far:
1. when I lose connection to my ISP then I can only ping internal ip addresses eg. another computer in my network
2. if I renew my ip address on the Macbook then it works again in 2 minutts, then the same happens again. This is my network setup:
Router -> Switch 1 -> Switch 2
I also know that it is not the Macbook, because it have got a new motherboard, and it have been reinstalled also if I use the Macbook on a other network then it works fine.
All my other computers ( windows and linux ) works fine, no problems.
To me it looks like it is a Nat and/or DNS problem, but I can´t fine out what it is.
