Cisco WAN :: 2811 Bandwidth Getting Out Of Hand
Aug 29, 2012
I am looking for some tips on managing my router. I have noticed lately our bandwidth useage has gone up and maxing our DSL line.Cacti is monitoring just for traffic trending and I am in the middle of getting NetFlow going.
Our router sits on the edge with no internal way to access it (or at least so I think right now.)
My thought is to enable NetFlow and port forward it into our network and use ManageEngine to see whats going on.I dont have any ACLs running on the router... We have two connections DSL and T1, I have them into a routing policy.Our nating and firewall sit behind the 2811.
View 1 Replies
ADVERTISEMENT
Jun 10, 2013
We have two Cisco 2811 Routers setup with a GRE tunnel that we would like to constrain the bandwidth on to replicate a satellite connectinon of 400 kbits. We tried the bandwidth command 400, but from what I understand that is only for routing metrics and not actual speed of the interface.
View 5 Replies
View Related
Aug 29, 2012
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
View 7 Replies
View Related
May 1, 2012
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies
View Related
Jan 6, 2011
I got connected ASA ----- ROUTER 2811) to metroethernet switch from my ISP , with a 4MB of bandwidth but the internet connections to all my LAN has been frozen and we lost connection to the internet, to restart the internet service I need to boot the ROUTER 2811 - and ISP switch to rollback the internet operation,My ISP support tell me if is possible to set up the traffic bandwidth in one or both borders devices, ( ASA 5510 or ROUTER 2811)
View 3 Replies
View Related
May 1, 2012
I have a cisco Swtich SGH 300-20 Gigabit switch i configure 2 vlan one is default and one is vlan 10
Vlan 1 ip range 172.16.0.0/23
Vlan 10 ip range 172.16.2.0/24
Client on Vlan getting Proper IP from DHCP Server all i need is to distribute internet bandwidth we have 6/3 mb and i want to give 4/2 mb to vlan 1 and 2/1 mb to Vlan 10
Int Gi16 on switch is configured as trunk port and is connected to cisco 2811 router
what are the command used to distribute bandwidth between these 2 vlans
View 3 Replies
View Related
Mar 23, 2013
I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
View 2 Replies
View Related
Aug 29, 2011
I am switching to a single Ethernet hand-off from my ISP which currently gives me 4 T1 lines. I have a Cisco 3845 router that services the current T1s. My question is since my ISP is giving me just a single Ethernet hand-off going forward can I connect it directly to the internal NICs on the 3845 or do I have buy some other HWIC?
I will be running a 100Mbps connection over the hand-off and the NICs are Gigabit NICs. I will not be doing anything fancy over this, just simply a couple of routes in the routing table. No VPN, no fire walling, etc. The specs state that the 3845 is only for up to a T3 speeds but I am not sure if that is for the HWIC interfaces or for the whole thing in general?
View 3 Replies
View Related
Nov 26, 2011
is it possible to setup any given hand held device with my in home Internet connection. cable to modem to wireless router to device i.e. without paying for an extra service? would an Internet connection be necessary in order to network a hand held device with my pc?is it possible to network a hand held device say the Droidx2 with my pc to act as a sort of desktop remote control?
View 3 Replies
View Related
Oct 4, 2012
I have a wireless access point, I want to be able to hand out addresses via the Cisco router through DHCP on the interface eth0/1. The wireless users that get an IP I want then route out the eth0/0 interface to my statically assigned default gateway. Right now Im not concerned with setting up security measures once this works I'll go back in and add that. Here is my running-config. Right now nothing from the 10.0.0.0 is being routed out to the internet.
View 6 Replies
View Related
Dec 26, 2011
My cisco representative tells me that I am limited to 10 IP addresses for my 10 user license on an ASA 5505 even though the Cisco documentation specifically states that a 10 user license allows the maximum DHCP clients to 32 IP addresses.
I want to have 30 computers get IP addresses from the ASA, but don't need any but one or two to get outside the internal network. Is this possible with a 10 USER license.
View 19 Replies
View Related
Sep 27, 2011
My cisco representative tells me that I am limited to 10 IP addresses for my 10 user license on an ASA 5505 even though the Cisco documentation specifically states that a 10 user license allows the maximum DHCP clients to 32 IP addresses.
I want to have 30 computers get IP addresses from the ASA, but don't need any but one or two to get outside the internal network. Is this possible with a 10 USER license.
View 1 Replies
View Related
Jan 31, 2012
Currently our Cisco 3750 have one interface (port 1) that connected to our provider (Internap) with the IP 66.150.7.68 assigned. Now we want to upgrade to dual handoff L3 protocol. Below is the network configuration from Internap.
>>>> We have assigned the below /30s for each of the interfaces and will statically route the 66.150.7.0/25 down both interfaces.
>>>>
>>>>
>>>> 63.251.162.20/30
>>>> 63.251.162.21 - border1.sef003 - Internap side
>>>> 63.251.162.22 - your side
>>>>
>>>> 63.251.162.184/30
>>>> 63.251.162.185 - border2.sef003 - Internap side
>>>> 63.251.162.186 - your side
tell what command lines do I need to input on my Cisco switch for port 1 and 2 in order for the dual handoff to work correctly?
View 1 Replies
View Related
Sep 28, 2010
I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
View 3 Replies
View Related
May 19, 2009
How to get this unit to hand out the Ip numbers in my network with dhcp but to allso assign these numbers in accordance to the mac address. I want o make sure the same computers get the same internal ip and not random ones?
View 2 Replies
View Related
Dec 26, 2012
I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans. It is connected to my router address 192.168.1.1. I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet.
Here is the config that I have. I deleted the other ports because I am not using them. The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1.
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
View 12 Replies
View Related
May 27, 2012
We have upgraded our gateway router from a Cisco Linksys RVL200 to a Cisco 861, this is a big jump from a GUI driven system to IOS CLi and i'm having issue finding my feet. I tried the Cisco CP system but it didn't work so I'm going to configure it with IOS commands. I wish to replicate the current configuration on the 200 with the following setup.
I have created a DHCP pool but i am unable to configure the FastEthernet ports to hand out address automatically, the pool is called USERS with range 192.168.1.30 -> 192.168.1.253.How do I work out the client-identifier for a DHCP client, I don't want to plug this into the network and manual reconnect all the PC's just to get the ID then make a static route.
View 8 Replies
View Related
May 17, 2013
I own a Dell Latitude D600 that I purchased off of Ebay a few months ago. For the past month I have been having an issue with my wireless card. My problem started when I turned on my computer and booted up and when my desktop loaded, no wireless icon or signal strength showed on the bottom right hand corner where are the other icons are. I went to Device Manager and in the Network adapter section was an exclamation point next to the Dell Wireless 1450 Dual Band WLan mini pci card which showed that there is a code 10 error. I have tried uninstalling it but then I would always get the BSOD with the BCMWL5.sys error. I have tried updating the driver as well but it would tell me that it already is up to date. I have also tried reinstalling my OS but my code 10 error always returns. When I opened up my laptop to see if the card is the cables are loose (which they weren't), I noticed that my wireless card is the Broadcom 4309.
I would also like to ask exactly what order am I suppose to have all of my drivers installed? I am almost positive that I am not installing them correctly. I have seen websites that say to install the Intel Chipset and O2 Smart Card first and then the NSS and so on.
View 11 Replies
View Related
Sep 9, 2011
We have 1 mpbs bandwidth line, but most of the time we are getting only 300-500 kpbs download speed, i want to send statistics report to our ISP, what will be best procedure to test the bandwidth report, i have checked in some websites like bandwidthplace and speedtest but these sites are not accurate, how to check the actual bandwidth we getting from ISP against 1 Mbps. We have solarwinds monitoring tool in this i have configured the WAN interface for 1 mbps
View 5 Replies
View Related
Sep 19, 2012
My setup is ISP-2811-PIX 515E-LAN. Right now, I am doing a PAT for IPSEC tunnels to terminate on the PIX. Do you recommend I use the 2811 instead of PIX for VPN or keep things the way it is? Trying to determine the best box to use.
View 4 Replies
View Related
May 27, 2013
I need to know which IOS should I download for my 2811 router to get all ip sla features
Router(config)# ip sla ?
<1-2147483> Entry Number
auto
enable
Note this is from my 2951 router.
I need full features like this in my 2811 router.so which IOS should I download.
View 3 Replies
View Related
Feb 29, 2012
I want to upgrade LMS 3.2 to 4.1. But when I look to "Special Notes and Exceptions for Devices Supported" document ,It seems that 2811 have 2 SysID.
Why there are two IDs for the same hardware and under which ID will my 2811 routers be classified into inventory database. This information is important since customer want to have support of 2811 in CiscoView of LMS 4.1 (around 200 devices).
View 3 Replies
View Related
Aug 23, 2012
Looking to implement CoPP in our 2811 ISR. We currently have the base 256mb of DRAM in there. Will this bring our router to its knees? I've priced a RAM upgrade.
View 0 Replies
View Related
Mar 19, 2012
i have a branch router that connects to mpls WAN. Also has a second interface that is used for dmvpn failover in case WAN goes down.We want to use this second interface also as the primary internet circuit for the branch. I changed the default route to the next hop address on the other side of the second interface and expected this to work.But i was told i need to set up NAT for this to work, and set up an ACL for NAT to use. how to set up NAT?
View 1 Replies
View Related
Nov 2, 2011
I have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies
View Related
Nov 8, 2011
I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
View 5 Replies
View Related
Feb 14, 2013
I have a 2811 that I can remotely VPN to using Cisco VPN client however I cannot see the internal admin network (10.35.5.0).
Current configuration : 4845 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
View 2 Replies
View Related
Sep 23, 2012
I have a particular site that is causing me trouble, this site is connected in a back to back configuration using 2811 at CO and 2621XM at CPE. The CO end is also the CO for 3 other sites so has a total of 4 wics installed (WIC-1SHDSL-v2), these other sites also have 2621XMs for the CPE.
The problem i am getting is when one site in particular transfers large files to/from client machines, the CPU on the 2811 jumps to 99%:
CPU utilization for five seconds: 99%/98%; one minute: 26%;
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
11 12881868 37249378 345 0.49% 0.50% 0.51% 0 ARP Input
54 8548592 30375358 281 0.40% 0.45% 0.41% 0 XDSL BACKGROUND
[Code]......
View 2 Replies
View Related
Apr 20, 2013
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.
View 5 Replies
View Related
Mar 22, 2012
I have a Cisco 2811 with an additional HWIC-4ESW card. [code] I need to NAT anything heading out of the WAN port. [code] I can ping anything connected to my other private networks from my 10.0.24.0 network but nothing on the Internet. [code]
View 3 Replies
View Related
Jan 3, 2012
I just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies
View Related
Sep 4, 2011
I want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
View 1 Replies
View Related
May 26, 2012
I have a 2811 ISR configured to provide the following services to my network: Internet access to LAN usersCisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations.Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)? While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 2 Replies
View Related
