Network A Hand Held Device (Droidx2) With PC

Nov 26, 2011

is it possible to setup any given hand held device with my in home Internet connection. cable to modem to wireless router to device i.e. without paying for an extra service? would an Internet connection be necessary in order to network a hand held device with my pc?is it possible to network a hand held device say the Droidx2 with my pc to act as a sort of desktop remote control?

View 3 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT54GX2 To Hand Out IP Numbers In Network

May 19, 2009

How to get this unit to hand out the Ip  numbers in my network with dhcp but to allso assign these numbers in accordance to the mac address. I want o make sure the same computers get the same internal ip and not random ones?

View 2 Replies View Related

Cisco Switching/Routing :: 6509 Mac Table Held

Feb 6, 2013

On the 6509, with normal 67xx cards installed, where is all the mac table held, is it held on the card itself or on the supervisor? And if I use dcef cards, I gather the MSFC copies the mac table to the DFC ?

View 1 Replies View Related

Cisco WAN :: 2811 Bandwidth Getting Out Of Hand

Aug 29, 2012

I am looking for some tips on managing my router. I have noticed lately our bandwidth useage has gone up and maxing our DSL line.Cacti is monitoring just for traffic trending and I am in the middle of getting NetFlow going.
 
Our router sits on the edge with no internal way to access it (or at least so I think right now.)
 
My thought is to enable NetFlow and port forward it into our network and use ManageEngine to see whats going on.I dont have any ACLs running on the router... We have two connections DSL and T1, I have them into a routing policy.Our nating and firewall sit behind the 2811.

View 1 Replies View Related

Cisco WAN :: 3845 - Ethernet Hand-off From ISP

Aug 29, 2011

I am switching to a single Ethernet hand-off from my ISP which currently gives me 4 T1 lines.  I have a Cisco 3845 router that services the current T1s.  My question is since my ISP is giving me just a single Ethernet hand-off going forward can I connect it directly to the internal NICs on the 3845 or do I have buy some other HWIC? 

I will be running a 100Mbps connection over the hand-off and the NICs are Gigabit NICs.  I will not be doing anything fancy over this, just simply a couple of routes in the routing table.  No VPN, no fire walling, etc.  The specs state that the 3845 is only for up to a T3 speeds but I am not sure if that is for the HWIC interfaces or for the whole thing in general?

View 3 Replies View Related

Cisco 2611 Router - Enable To Hand Out Addresses Through DHCP

Oct 4, 2012

I have a wireless access point, I want to be able to hand out addresses via the Cisco router through DHCP on the interface eth0/1. The wireless users that get an IP I want then route out the eth0/0 interface to my statically assigned default gateway. Right now Im not concerned with setting up security measures once this works I'll go back in and add that. Here is my running-config. Right now nothing from the 10.0.0.0 is being routed out to the internet.

View 6 Replies View Related

Cisco Firewall :: 10-User License For ASA5505 Allows DHCP To Hand Out 32 IPs?

Dec 26, 2011

My cisco representative tells me that I am limited to 10 IP addresses for my 10 user license on an ASA 5505 even though the Cisco documentation specifically states that a 10 user license allows the maximum DHCP clients to 32 IP addresses.
 
I want to have 30 computers get IP addresses from the ASA, but don't need any but one or two to get outside the internal network.  Is this possible with a 10 USER license.

View 19 Replies View Related

Cisco Firewall :: 10-User License For ASA5505 Allows DHCP To Hand Out 32 IPs

Sep 27, 2011

My cisco representative tells me that I am limited to 10 IP addresses for my 10 user license on an ASA 5505 even though the Cisco documentation specifically states that a 10 user license allows the maximum DHCP clients to 32 IP addresses.
 
I want to have 30 computers get IP addresses from the ASA, but don't need any but one or two to get outside the internal network.  Is this possible with a 10 USER license.

View 1 Replies View Related

Cisco Switching/Routing :: 3750 / Dual Hand-off L3 Protocol?

Jan 31, 2012

Currently our Cisco 3750  have one interface (port 1) that connected to our provider (Internap) with the IP 66.150.7.68 assigned. Now we want to upgrade to dual handoff L3 protocol. Below is the network configuration from Internap.
 
>>>> We have assigned the below /30s for each of the interfaces and will statically route the 66.150.7.0/25 down both interfaces.
>>>>
>>>>
>>>> 63.251.162.20/30
>>>> 63.251.162.21 - border1.sef003 - Internap side
>>>> 63.251.162.22 - your side
>>>>
>>>> 63.251.162.184/30
>>>> 63.251.162.185 - border2.sef003 - Internap side
>>>> 63.251.162.186 - your side
 
tell what command lines do I need to input on my Cisco switch for port 1 and 2 in order for the dual handoff to work correctly?

View 1 Replies View Related

Cisco Wireless :: 1141N To Make DHCP Server Only Hand Out IP Addresses

Sep 28, 2010

I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.

View 3 Replies View Related

Cisco WAN :: Setup 3550 Layer 3 Switch To Do Hand Out Dhcp Addresses For Different Vlans?

Dec 26, 2012

I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans.  It is connected to my router address 192.168.1.1.  I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet. 

Here is the config that I have.  I deleted the other ports because I am not using them.  The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1. 

version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption

[code]....

View 12 Replies View Related

Cisco Switching/Routing :: 861 - Can't Configure FastEthernet Ports To Hand Out Address Automatically

May 27, 2012

We have upgraded our gateway router from a Cisco Linksys RVL200 to a Cisco 861, this is a big jump from a GUI driven system to IOS CLi and i'm having issue finding my feet. I tried the Cisco CP system but it didn't work so I'm going to configure it with IOS commands. I wish to replicate the current configuration on the 200 with the following setup.
 
I have created a DHCP pool but i am unable to configure the FastEthernet ports to hand out address automatically, the pool is called USERS with range 192.168.1.30 -> 192.168.1.253.How do I work out the client-identifier for a DHCP client, I don't want to plug this into the network and manual reconnect all the PC's just to get the ID then make a static route.

View 8 Replies View Related

Dell :: D600 No Wireless Icon Or Signal Strength Showed On Bottom Right Hand Corner

May 17, 2013

I own a Dell Latitude D600 that I purchased off of Ebay a few months ago. For the past month I have been having an issue with my wireless card. My problem started when I turned on my computer and booted up and when my desktop loaded, no wireless icon or signal strength showed on the bottom right hand corner where are the other icons are. I went to Device Manager and in the Network adapter section was an exclamation point next to the Dell Wireless 1450 Dual Band WLan mini pci card which showed that there is a code 10 error. I have tried uninstalling it but then I would always get the BSOD with the BCMWL5.sys error. I have tried updating the driver as well but it would tell me that it already is up to date. I have also tried reinstalling my OS but my code 10 error always returns. When I opened up my laptop to see if the card is the cables are loose (which they weren't), I noticed that my wireless card is the Broadcom 4309. 

I would also like to ask exactly what order am I suppose to have all of my drivers installed? I am almost positive that I am not installing them correctly. I have seen websites that say to install the Intel Chipset and O2 Smart Card first and then the NSS and so on.

View 11 Replies View Related

Home Network :: Use Access Point As Main Network Device

Aug 15, 2012

I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)

View 2 Replies View Related

Unknown Device In Network?

Jan 19, 2011

Since i got sky broadband it's always been running super slow, the amount of times i have called them is ridiculous. So i have just been looking around on the sky address to see if i can fix it and in my Attached devices i have, the pc, an ipod touch and an unknown device. I'm wondering if this has anything to do with the slow speeds and maybe it's somehow 'stealing' my broadband. I've read a previous post of the same type but that wasnt for sky. i ran the ipconfig/all into CMD

View 1 Replies View Related

Home Network :: Lan Device Not Recognized

Aug 3, 2011

I just got this av to cat5 converter [URL]? and was thinking i could use a router on each end so it could be wireless. But the way they work the router does not see the converter when it is plugged in.

View 9 Replies View Related

XP And Windows 7 Network - Cannot Open Either Device From Other One

Jul 9, 2012

This is 1st attempt at home networking:win xp pro to win 7 ultimate.can get both devices to ping and receive both by ip address and computer name.both devices seen in each others workgroup view. cannot open either device from the other device.file and printer sharing is on on both machines.

View 1 Replies View Related

One Device Crash Down Entire Network

Jul 21, 2011

I am in charge of taking care our small office network (about 25 PC's) and encountered a problem the other day. I got a call that nothing network related was working. I went to look at the switches/router and everything appeared fine. After some troubleshooting i found if i unplugged the switch and connected directly the the router everything worked prefect. Reconnected the switch, network goes down again. I assumed it was the switch at first but then did a walk around and a laptop was in a weird frozen state. I unhooked the network cable and everything started working away like it should.

View 9 Replies View Related

Convert 802.11a To 802.11g Wireless Network Device?

Feb 13, 2013

It is possible to convert 802.11a to 802.11g wireless network device. I wireless outdoor cpe which is work on 802.11a...i want to convert it to G network

View 3 Replies View Related

No LAN In Network Connections Device Manager

Apr 20, 2011

I just recently got the internet and I have a desktop computer that has ever rarely been used and it has never had the internet on it. I called tech support of my ISP to see what many be the problem why I can't connect to the internet and found that the source of the problem was I do not have a LAN network connection. When I open Network Connections on the computer, nothing is there. I also went to device manager and there is nothing there for Networking. Under category of "Other Devices" in Device Manager there is a question mark next to "Ethernet Controller". Are there drivers or something I need download to fix this so I can connect to the internet via a DSL connection.

My computer specs are:

Windows XP Professional
Version 2002
Service Pack 2

[Code].....

View 2 Replies View Related

Forgot Network Key Trying To Add Wireless Device

Nov 30, 2011

I forgot my network key trying to add wireless device

View 1 Replies View Related

Adding Non Standard Device To Network?

Oct 18, 2011

I have a machine which is connected to a PC using an ethernet cable to communicate information between the machne and computer.I am told that the machine uses the MAC address to communicate and the computer just needs an ip address in the same range as the machine and software aware of the machine's MAC address. Why I can't connect it though the network, I tried the manufacturer who couldn't explain

View 4 Replies View Related

Remove Other Home Device Network Map?

Feb 7, 2011

I want to remove au pairs computer from my home network as she's slowing everything down. Is there an way I can do this without her knowing?

View 1 Replies View Related

Wireless Network Device Is Disabled?

Apr 17, 2011

my laptop can't connect to a wireless network, so I have to keep it in one room connected to the modem. When I unplug it, even with the wireless switch on, it loses the connection. When I use ConfigFree, it says the wireless network device is disabled. I went to device manager and updated the driver for the network adapter, and it still said it was disabled. What should I do now?

View 6 Replies View Related

Servers :: No Network Adapter In Device Manager?

Apr 11, 2011

HP computer, was working last friday and today it isnt. Can not connect to the internet or outlook etc. Looked in BIOS says it is conected to LAN - tried enabling and disabling it and re-booting it. Still nothing. Had a tech guy that said to look in device manager, but network adapter was no where to be seen. What shall i try next to resolve this problem?

View 1 Replies View Related

Network Adapter Does Not Show On Device Manage?

Aug 19, 2011

Since downgrading from vista to xp on tower (packard bell bv)have had internet connection issues (no workie!).device manager shows no modem,but modem working fine through laptop wireless set up.odem is through virgin (netgear),have tried to find update for netgear drivers(no chance)but obviously modem is working ok through laptop!have also tried to find update on motherboard (m2 ns-nv, 1.xxbus clock 200mghz bios phoenix tech).

View 1 Replies View Related

Sagemcom 1704 - Setting Device For Network

Dec 10, 2012

How do I set up a Sagemcom 1704 modem for networking?

View 2 Replies View Related

Protocols / Routing :: Locked Out Of Device On Network

Apr 12, 2012

I had a custom device/computer on my network that was hacked from hong kong. It's one of those things where I seriously think the chinese have built a back door into it when they built it or something because everything was secured and monitored.The device runs it own OS or something like that I guess you could say. It can also run it in standalone mode broadcasting it's own signal. Once I figure this out I may not put it online anymore but thats besides the point right now. When it was hacked I'm pretty sure the port it uses to connect was changed from 80 to 591. When it runs in standalone mode I can connect to it but I am unable to actually access it's proprietary graphic network interface. It sends out UDP every few seconds or so and basically I was trying to search for some type of udp broadcast monitor and have tried using network tools such as netstat, port scanning, multicast, etc on all of the big three OS's because sometimes it seemed to finnicky what it wants to connect to. I've tried to let it connect back to my router again which it seems to do, but is then denied access and I think it may even have a trojan or somethng so I don't want it to that but if I have to to access it again I will.In standalone mode I've it usually trys to connect on 192...5 or 192...7 and I've tried to get through 591, 23, 80 etc. multiple times with no luck.

View 11 Replies View Related

Device Manager Does Not Recognize Network Adapter

Aug 30, 2012

co worker brought me his comuter to reinstall windows xp, because he did not like vista, he also had his own xp discs, i have done everything like normal, have done this a time or two not my first rodeo with reinstalling windows xp, this is however the first time that this network issue has happened, i have installed the device driver cd as well along with the reset tool from dell's website, im getting NOWHERE.

View 1 Replies View Related

Plugging Wired Device Into A Wireless Network?

Jan 25, 2011

I have a 2 computer wireless network running usb wireless devices connecting to a wireless router for internet. I need to plug a wired device (cctv dvr system) into one of the computers to get it on the internet. Do I use ICS or a bridge of some sort? I am going to be plugging that system into a computer running Windows 7.

View 5 Replies View Related

Android Device Won't Obtain IP Address From Network?

Sep 22, 2011

I just got the motorola droid 3, my first android device. I'm trying to figure out how to get my device to connect to my network as it won't obtain the IP address.I have a Motorola Surfboard SBV5120 Modem and a Microsoft MN-700 router. I just switched from the Palm Pre Plus which connected perfectly to this network, the network is unsecured and has 2 pc's and a 360 running on it. I was able to connect to my friend's wireless network fine at his house.

View 9 Replies View Related

One Device Won't Connect To Home Wireless Network

Jul 2, 2012

I recently upgraded my wireless router from D-Link DIR-615 to D-Link DIR-685. Before the changeover, all of my devices were connecting to the router, although I had several problems with dropped connections, etc. The devices in use were:

- Desktop computer
- Laptop computer
- All-in-one touchscreen computer
- Netbook
- iPhone (original model)
- HP TouchPad tablet
- Sony Blu-Ray player
- Two internet radios (Aluratek and Livio)
- Wii

ALL of these devices were connected wirelessly to the network. When I set up the new router, I used a different network name/SSID, but kept the same security key/password. All of the router settings were kept the same (e.g., WPA-2, etc.). After the new router was up and running, every single one of the devices listed above connected (after an initial setup with the new network name, of course) EXCEPT the All-in-one/touchscreen computer. I've tried over and over, and it refuses to accept the security key/password. (The desktop, laptop, and touchscreen are all running Windows 7 64-bit Home Premium.) After doing some research, I tried some suggested solutions, but nothing seems to work. Nothing on the problem computer has changed since it was last connected to the old router. I checked the "Properties" of the network device on both the Desktop (which has no problems connecting) and the Touchscreen, and they are identical: WPA-2, AES, etc. And I'm 100% positive I'm entering the security key correctly. I've rebooted the router and the computer several times.

View 14 Replies View Related

Use Access Point As Main Network Device?

Aug 15, 2012

I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N. What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection. How would I be able to do this?I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved