I recently upgraded my wireless router from D-Link DIR-615 to D-Link DIR-685. Before the changeover, all of my devices were connecting to the router, although I had several problems with dropped connections, etc. The devices in use were:
- Desktop computer
- Laptop computer
- All-in-one touchscreen computer
- Netbook
- iPhone (original model)
- HP TouchPad tablet
- Sony Blu-Ray player
- Two internet radios (Aluratek and Livio)
- Wii
ALL of these devices were connected wirelessly to the network. When I set up the new router, I used a different network name/SSID, but kept the same security key/password. All of the router settings were kept the same (e.g., WPA-2, etc.). After the new router was up and running, every single one of the devices listed above connected (after an initial setup with the new network name, of course) EXCEPT the All-in-one/touchscreen computer. I've tried over and over, and it refuses to accept the security key/password. (The desktop, laptop, and touchscreen are all running Windows 7 64-bit Home Premium.) After doing some research, I tried some suggested solutions, but nothing seems to work. Nothing on the problem computer has changed since it was last connected to the old router. I checked the "Properties" of the network device on both the Desktop (which has no problems connecting) and the Touchscreen, and they are identical: WPA-2, AES, etc. And I'm 100% positive I'm entering the security key correctly. I've rebooted the router and the computer several times.
Does a 802.11g compatible device on a 802.11n network slow the whole network down to 802.11g speed?I want to integrate a Logitech Squeezebox into my 802.11n home network but it is only rated at 802.11g.
I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
I just got this av to cat5 converter [URL]? and was thinking i could use a router on each end so it could be wireless. But the way they work the router does not see the converter when it is plugged in.
I have a video conferencing device that uses a lot of ports and is very bandwidth intensive. I have been messing around with two routers (cheap ISP Thomson and my Netgear DGND3300v2) settings for a couple of months now and I couldn't get it to work properly (ports were getting blocked randomly). I have recently discovered that Netgear has a "secret" page where you can switch the router to a modem mode. I gave the device a public IP and now it works fine (at least so it seems for now). The thing is, I need to connect another device (my PC) to the device via web interface for monitoring purposes. I am wondering what network arrangement would be best for me. I want the video device to have nothing to do with natting or firewalls at all, I want it to have a public IP. However, I also want to be able to connect to it somehow and also share the connection with my PC.
recently I've connected to my OpenVPN and everything works fine on my PC I'm getting okay speeds and the VPN IP appears on [URL]The problem is I wanna use internet connection sharing to play Xbox Live while connected through my VPN and I'm having issues.My Xbox isn't even recognizing my wired connection.This is the setup:Wireless Connection > Desktop > OpenVPN > Wired connection from desktop to XboxWhat I think I'm doing wrong is not specifying the correct home networking connection for my LAN 3 (Tap-Win32 Adapter OAS)I tried sharing the LAN 3 connection and set the home networking connection to my Wireless and it disconnects me from my wireless network.
I have linksys WRT120n (just bought it) now connected with ethetnet cable i have a laptop and an 2 iphones that wont connect the network after a while, the only way that solves the problem for a while is unplugging the router from the electricity and plugging it again and then after few hours or a day the problem returns.
Client Lease Time: 1440 the devices have an IP reservation network mode - mixed ( B G N )
My Wifi network has a wpa2 password that is a random string of characters and numbers and yet last month a rogue IP Address kept popping up on my DNS list. It has to be coming from my neighbor who's bedroom is about 15 feet away from my router. So unless someone is sitting out on my front lawn to do this then it must be him.I've been looking for software that will notify me when a connection my router is attempted and kudos if it also asks my permission first would be great.There are wifi packet sniffers out there like Cain&Abel, Airsnort, that sort of thing but I am not quite savvy enough nor do I want to turn this into a complicated hobby but just need a basic warningin case something gets past my passwords again
Region : Singapore Model : TL-WR941ND Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
I've problems connecting to my wireless network. i do not face this problem in the past until recently i've some problems with my laptop. after i re-format my laptop, i faced with this problem. here are some of the images i took.
I have set up a wireless network in my home using s d-link N+ 300 DIR-655 and the desktop that is directly connected to the modem and router can connect to the internet and my laptop can access the wireless network and get online but I have another desktop that cannot connect to the wireless network. It can see it but when i try and connect i get the message that it was unable to connect or sometimes that i was able to connect but have limited connectivity.
My laptop with Windows 7 64-bit is not being able to connect to the home wireless network. But other devises like iPad and iPhone and Mac laptop can connect to the same wireless network. However I can connect to the network if I connect my laptop directly to the wireless router using a network cable.I have tried upgrading the firmware in my wireless router but no luck. THis laptop had no problem before connecting to the same wireless network. But since I came back from the back home couple of days back I am seeing this problem. But my laptop can still connect to my my-fi devise wireless network. I have tried running the netsock commands listed in a similar thread in this forum but no luck.netsh winsock reset catalog netsh int ipv4 reset reset.log netsh int ipv6 reset reset.log
I've tried everything possible to connect my blu ray player to my network. I've tried the auto setup, manual entry and cant come up with anything. I've followed all the instructions i can find on-line and i don't know if I'm overlooking something or what. I've got Philips blu ray home theater system and linksys wrt120n router
I have a work supplied laptop. Used to be able to connect to my home wireless network - this stopped working last week. It can connect to other wireless networks, both at the office and other public places, but can't connect to my home network.
I've tried: Manually creating the wireless network Removing the profile from regedit Removing the profile from ProgramDataMicrosoftWlansvcsProfiles
It sees the network and attempts to connect, but never successfully connect. I have other laptops at home that are working just fine. The network is setup with WEP security, and I've entered/reentered the password several times.
Note, when I started this, the home network did not appear under the Manage Wireless Networks list in the Network and Sharing Center.
first I replaced a new internal hard drive. Installed new and updated drivers. connected to the home wireless network. everything working well so far as of last week. this week, I replaced new battery and ran norton 360 updates. after the updated, I can't connect wirelessly to my home network. I checked if Norton is blocking the communication but I don't think it did.
How can I connect a vista laptop to existing wireless home network with other 3 [COLOR=#000096 !important][COLOR=#000096 !important]xp[/COLOR][/COLOR] machines.I followed googled info but keep chasing my tail as all effords end trying to make an internet connection. [code] is Negear wired & wireless capable in which 2 PCs are wired & an Acer netbook wireless connected, all 3 XP machines.
Ok I have a toshiba satellite with the above stated modem in place, however I am not sure if the modem is wireless capable. I have been trying to figure out how to connect it to my network.
I have a dell inspiron 1545 and my internet was working fine last night. My laptop restarted at some point during the night and now it can't connect to my normal wireless network. when I use my phone as a wifi hotspot, my laptop can connect to it.My desktop connects to my home's wireless network fine so I'm not sure why my laptop, which can connect to other networks fine, can't connect to my working home network
1. Green Packet DX-230 WiMAX modem with router 2. D-Link DIR-615 ver G2 (from my ISP) 3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
I recently installed a new router - WRTP54G . I used to have our 2 machines on a home network. However, that is all gone now. When I open My Network Places on my pc, nothing at all appears. On the other pc only the shared folders on that pc appears. I've tried running the network wizard several times and to no avail. I've checked the permissions and everything else I can think of, but it still doesn't work. I believe it is probably something simple to fix, like checking the right box, but I haven't found it yet. Both machines are running XP Home and I have an external drive attached to my pc. Everything worked fine till the installation of this new router. Should I just create a new network? Would that just be easier? One more thing, I got the error that says Home is not accessible. You might not have permission to use this network resource. Contact admin of this server to find out if you have access permission. The network path was not found. Of course, I am the admin.
I am unable to connect my Ipad3 to my home network (WRT160N router). It has been working for the last 8 months, and stopped working after I installed Direct TV App on Ipad..It detects the network, but not accepts the PW.... I have multiple wireless devicess connected to my network without any problems..The funny thing is that my neighbor brings his ipad to my house and he is able to connect..My ipad connects to any other network...just not my home network.. I contacted Apple who spend hours with me on the phone and suggested doing a full reset on the ipad, but still did not solve the problem..I called and already paid for linksys support ($62.95) who spend hours with me on the phone, but suggesting: "maybe you need to buy another router"...REALLY!!!! Again, I have 3 Smart TVs, Xbox360, and Wii, that are connected to the network just fine .even my neibor comes with his Ipad3 and connects to my network just fine......and I can connect with my ipad to any other network without any problems... BTW, I have already removed the DirectTV app from the ipad....but I still cannot connect to my network..
I have a xbox 360 that I want to connect to xbox live with, using my home network. Every time I try to connect to xbox live the only part that fails is the connecting to xbox live part. This is how my network is set up. I have Cox Cable as my ISP, a Linksys WCG200 gateway(v2), and WRT54GS(v7). The cable wire is connected to the WCG200 gateway, then an Ethernet cable connects the gateway to the WRT54GS router, and finally an Ethernet cable connects the router to my xbox 360. I have contacted Cox, Linksys, and Microsoft about the situation and they all say the problem is the version of the router. Someone told me that I may just need to change the firmware, but I don't know how to do that.
I have just bought a TP-Link Wireless Access Point (TL-WA&01ND) and an ethernet switcher (TL-SF2005D).I have put the access point into client mode, allowing me to put it in my room and wirelessly connect to my router, allowing me to plug my PC in over ethernet and use the internet. However, after much fiddling with settings I cannot get it to work, as it continually searches for a network, and then fails to connect, despite the fact it is configured to use the network?I already have a similar setup with a netgear wireless G access point which works, and so I dont understand why the new box cannot do this when using what I believe to be the same settings.
Secondly I have an ethernet switch box which I bought to connect to the access point and switch the ethernet signal between my two PCs, my xbox and PC. This works fine with my primary PC (over my old access point) but when I try to connect my PC i get a DNS failure with auto IP settings and a gateway failure with manual settings, and other devices refuse to connect.
Camera set up with the Beta Mac wizard connected via ethernet on Airport base. Wireless security WPA2 Personal. Using DHCP. AirPort Utility 5.5.2, OSX 10.6.6.I can see the cam with the myDlink Lite iPhone (4) App when I am in my house with my wireless network. When I am out, away from my network, the App can't connect to the cam, tells me to check my network settings. I did the wps way and added the cam in the airport base utility *Access Control* tab but still doesn't work. Checked in the cam web page settings, can't figure out what the Pre-Shared Key is and where I get it/set it up in the airport utility...
I have a computer running Windows Vista that has been unable to access the internet, either with wireless or cable. It just says that no connections are available.Troubleshoot doesn't detect any problems.I also realized that I cannot access device manager, nor can I add/uninstall anything. When trying to get into device manager, I get " the specified service does not exist as an installed device".
I just upgraded my wireless router to a D-Link DIR-655. I have 2 PCs and a network storage device (D-Link DNS 321) connected via ethernet to the router. I also have an xBox 360 connected wirelessly to the router. The xBox is able to connect to the internet via the router, but it cannot connect to (see) the PC's or the network storage device. It was able to do so with my old wireless router (a Belkin), but it stopped with the DIR-655.
