TP-Link 300Mbps Wireless :: WR941ND Connect Device Which Only Has LAN Port To Network
Feb 20, 2013
Region : Singapore
Model : TL-WR941ND
Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
View 7 Replies
ADVERTISEMENT
Mar 25, 2013
Region : India
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.6
ISP :
We need to configure the AP in such a way, only 1 antenna to be used & not other two, to meet some mounting requirements/limitations. Will I be able to do this using any test/debug commands?
Essentially I want this AP to be operating in 1x1 spatial stream, & with no antenna diversity, so that I can connect only 1 antenna & be deterministic about AP using only connected Antenna RF port & not others
With out configuring anything, when I connect only 1 Antenna, I observed that signal is fluctuating on Client Application & causing the applications traffic stream disconnect.
View 1 Replies
View Related
Jan 2, 2013
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have a problem with files sharing via wi-fi. I can not share files over the network using wi-fi connections. While the network is the cable connection sharing is available. The network also acts as one computer is connected by a cable to the router and the other via wifi. But if the two computers are working through wifi network does not work. Are there any settings in the router, which can cause blocking calls via wifi?
View 1 Replies
View Related
Feb 16, 2013
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP : Bezeq benleumi
I want to setup WDS using my TL-wr941nd WDS router?
View 7 Replies
View Related
Dec 25, 2012
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have two(2) WR941ND routers working at my home. The primary has IP : 192.168.1.2 , this primary router is working as an Acess Point, DHCP is OFF, and no wireless security activated. This primary router is connected to a DSL modem+router and DHCP is activated on it.For the secondary router I configred 192.168.1.100 . On the secondary router I have activated WDS function as well as Wireless Security (WPA2) , DHCP is Off on it. This secondary router is to work as wireless bridge + Access Point. You will understand that this secondary router is wirelessly connected to the primary one.I am able to configure all, and all things work correctly for few days at a time.But if at any time the secondary router is switched OFF, and then again switched ON, it seems to have lost al the settings and its IPs, and thus unable to connect to primary router. At such time I am unable to locate /connect my laptop to this secondary router, and it keeps on searching & searching.
View 1 Replies
View Related
Feb 1, 2013
Region : Canada
Model : TL-WR941ND
Hardware Version : V5
Firmware Version : wr941nv3_en_3_13_9_up(120201)
ISP : Teksavvy
This wireless router keeps freezing. It might stay up for 6 hours at the most, then I have to reset it or unplug for 10 seconds to get it to reset. I updated the firmware a few months ago thinking this would solve the problem. It hasn't.
View 2 Replies
View Related
May 6, 2013
Region : Greece
Model : TL-WR941ND
Hardware Version : V5
Firmware Version :
ISP :
Does TL-WR941ND provide support for 802.1x? (It is not mentioned in the product data sheet, but I found here: [URL] that it is supported on the above device.)
View 1 Replies
View Related
Jan 14, 2013
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : TDS
Currently I am using 2 WA5210Gs and a WR941ND to send my wireless connection from one home to another. The original home utilizes a TDS DSL modem/router combo. Everything works great, but then generally withing 24 hours I will randomly drop my internet connection in the second home, but the network is still up and running strong. The modem is not the problem, because I am able to grab a faint signal from the WA5210G AP connected to the modem and access the internet, and the client WA5210G AP is running at full signal. If I power down the router and restart it, the problem is fixed, but happens again within 24 hours. Originally I changed the IP on the WR941 thinking it was an IP conflict with the modem/router, but the problem occurred again. I also tried switching to unicast DHCP, but the problem still persisted. I looked for a firmware update, but couldn't find a newer version..
View 5 Replies
View Related
Jan 31, 2013
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : TL-WR941ND_V2_V3_120201
ISP : Cox
I updated my firmware due to connection issues, now it gets stuck when trying to load the console. I can see the grey pipe separators on the screen, but nothing else. I've tried chrome, firefox, and IE, but still nothing. The wireless AP is active, and i can connect wirelessly, and i can ping it. just cant get the console to show.
View 9 Replies
View Related
Mar 23, 2013
Region : Australia
Model : TL-WR941ND
Hardware Version : WR841N v8
Firmware Version : 3.13.27 Build 121101 Rel.38183n
Model : TD-W8968
Hardware Version: TD-W8968 v1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
I have two routers, a TP-Link TD-W8968 (main & connected to ADSL) and a TL-WR841N (client) and I'm trying to get WDS working over them in order to use my PS3/media player etc at the tv.
1) are these 2 pieces of hardware compatible for WDS? Status of both hardware seems to indicate yes
2) if compatible, what am I missing so devices behind the client router can access the internet connection.
View 10 Replies
View Related
Feb 9, 2013
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel. 54965n
ISP : Toya Lodz
This is already my second model of the router, which got under warranty. The first model had a problem because it brokes off Internet connections. This second model also breaks the connection. I'm going to give it to complain. Before I do it I would like to ask if there are any ways to improve the router without the need to dispose of the device.
View 14 Replies
View Related
Mar 10, 2013
Region : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
View 2 Replies
View Related
Dec 6, 2012
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : 3.6
ISP : comcast
what do i need to do to have my laptop access an Iomega EZ networked external hard drive? It is not my firewall on computer so Norton said it is the router.
View 1 Replies
View Related
Apr 9, 2013
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world.
* LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24).
* DHCP is also disabled as this service is already provided.
* Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
View 6 Replies
View Related
Jan 6, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmwar Version :
ISP : AT&T
I recently got a new modem from AT&T. I hooked it up and everything worked fine for a few days. Last night some friends came over with their wireless devices (iphone, ipad) and after a while, the internet got really slow. Then it was unresponsive but it said that we were still connected to the network. So I decided to restart the router. Once it was finished rebooting, we were not even able to connect to the network at all. Even on my computer downstairs I was not able to connect wirelessly. I am connected via ethernet from the router right now on my computer upstairs and that is working fine. I have tried rebooting the router to factory settings, unplugging the modem, rebooting the modem, unplugging the modem, changing the router settings, pretty much every practical solution for simple connectivity issues.
View 1 Replies
View Related
Dec 26, 2012
Region : Austria
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
unfortunately I've lost my device pin and I've reset my device.can I get the device pin on a other way? on my invoice there is no information about that.
View 1 Replies
View Related
Dec 8, 2012
-Model : TL-WR1043ND
-Hardware Version : v1
-Firmware Version : 120605
I'm wondering if USB HDD spin down capability does exist on the deviceI think this enhancement will be serve a lot of costumers who wish to use all USB features.
View 1 Replies
View Related
Jan 7, 2013
Region : NewZealand
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
I've plugged in a USB flash drive and enabled shared storage on my TL-WR1043ND router. With "Access shared storage with password" unticked, I can access the share using both my Windows 7 Laptop and Motorola Defy+ (with ES File explorer) and successfully play any Music off of the network share using the Android App, ES File explorer.
If I enable "Access shared storage with password" and attempt to log in using any of the user accounts I've set up on the device, I will be able to access the shares using the credentials on my Windows 7 Machine, but not with my Motorola Defy+, instead I will simply receive "Login failure". I'm Picking it has something to do with the network share type?
View 4 Replies
View Related
Jan 29, 2012
I have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies
View Related
Apr 10, 2013
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 1.4.0 Build 111130 Rel.55990n
ISP : Titanadsl
My router is a TD W8960N v3 which isn't listed here.I've connected a Synology 110j to the router and need to sort out the port forwarding which I'm not much good at. I am finding the TP Link documentation. I did find the page on DMZ but I don't know what that is.
View 4 Replies
View Related
Mar 16, 2013
Region : Malaysia
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.12.9 Build 120221 Rel.31475n
ISP : UNIFI Telekoms
I am doing port forwarding for 2 webservers i have IP Address is 192.168.0.2 and 192.168.0.4 Both have web apps running find within LAN, both run on port 80.Error code: 14004.
View 8 Replies
View Related
Feb 7, 2013
Region : Germany
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 121127
is it possible to use the Print Server on the TL-WR1043ND without installing the "Printer Controller Utility"? I have a HP LaserJet 1022 (in compatiblity list) connected which is recognized by the TL-WR1043ND. I want to connect the printer manually to my Windows PC using standard tcp/ip port, but I can't get it working. I tried RAW with Port 9100 and LPR with lp1. What are the right settings??
View 1 Replies
View Related
Dec 31, 2012
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version : 3.12.5 Build 100929 Rel. 57776n
ISP :
I have a TP Link router model number: WR941N (under hardware version it says "v2/v3", that's why I put "not clear" under "hardware version" in the form). Whether it was possible to add even more slots for Port Forwarding for this router, the current hard limit is 16, and I would like to have more than that, what would be the procedure to do so?
View 2 Replies
View Related
Jan 18, 2013
Region : Australia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
Yesterday I got a new TP-Link TL-WR1403ND Wireless N router. And after trying for ages to try to connect my Galaxy Nexus and iPad (both Wireless N devices), I finally called the TP-Link Support.Both devices could see the wireless, but would never let me join.Anyway, support told me to try connect a laptop if I had one, which I did (a very old one) and it also could not connect. The first thing the tech got me to do was set the mode from mixed-b/g/n to mixed-b/g. This got it to work, and the tech basically said � there you go, works. But the main reason I got this router was to use wireless n.Anyway, I told her that was not acceptable, she then told me to set it back and change the security to WPA-PSK (it was WPA2-PSK). I did this and she also told me to disable WMM.Anyway that worked, so I was happy. I then went and change the security back to WPA2, and it still worked. So the main issue stopping me from connecting to the WiFi from my devices was WMM.So after all that... I looked up WMM, and can see it basically a QoS feature. So why does it not work with my phone, ipad and laptop? I have searched the net, and from what I can see, it is a very Important thing to have WMM turned on. So why won't it work with my devices? All three of them can see the wireless network, I can put the password in, but then they don't connect.I am on the latest firmware (can't check the actual name and version as I am not at home), so is there something wrong with this particular router? Is it a known problem? Do I have a faulty unit?
View 6 Replies
View Related
Mar 23, 2013
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : Plusnet
I'm on a fibre connection from Plusnet and bought the TL-WR1043ND because of the advertised ability to use PPTP VPN to connect to my work server (the supplied Plusnet router doesn't allow it and is locked down).However, I cannot connect via PPTP VPN on this TL router either. I know my VPN settings are correct and I have had a brief search and found others have this problem, but short of installing third party firmware on the router, how to get this router running my PPTP VPN?
View 1 Replies
View Related
Nov 29, 2012
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 3.13.18
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways!
I am living in a dormitory. And the website of the ISP is url... which provides dynamic IP. I have already tried different LAN IP adresses.I have already tried MAC Clone for WAN but nothing changes.I'm in a dormitory, there is also other routers here, could it because of conflicts with the other routers? [code]
View 4 Replies
View Related
Nov 29, 2012
Region : Germany
Model : TL-WR841ND
Hardware Version : V3
Firmware Version : 3.13.18
ISP : [url]...
I recently bought a wireless N router (TL-WR841ND). I could connect my laptop to internet using the router but the problem is whenever I try to connect my phone to the wireless network, it goes on and off. It'll be on for a few minutes and then it is off and so on. By the way, the phone says you're still connected to the router but actually there is no real internet connection. But anyway, my laptop is connected to internet anyways! I have already tried MAC Clone for WAN but nothing changes.[code]....
View 1 Replies
View Related
Jan 29, 2011
I just upgraded my wireless router to a D-Link DIR-655. I have 2 PCs and a network storage device (D-Link DNS 321) connected via ethernet to the router. I also have an xBox 360 connected wirelessly to the router. The xBox is able to connect to the internet via the router, but it cannot connect to (see) the PC's or the network storage device. It was able to do so with my old wireless router (a Belkin), but it stopped with the DIR-655.
View 4 Replies
View Related
May 13, 2013
Region : India
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version :
ISP :
i bought the TL-WR841N a week back. the problem is that the internet connection has a web based login( wherin i have to go the "login.hathway.com" and enter a username and password provided by the service provider). i was wondering if there is anything i can do so that the wifi router on its own can log on to my account automatically every time i connect a device to the router. This would save alot of time for me.
View 1 Replies
View Related
Feb 20, 2013
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V5
Firmware Version :
ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
View 2 Replies
View Related
Mar 1, 2013
Region : Canada
Model : TL-WR1043ND
Hardware Version : V1
I was wondering if it is possible to connect two routers through wireless and make them talk to each other. Here is why I need it, I currently Have 6 wireless IP Cameras going too 8. 2 are wired on one router in my house and the other 4 are wireless(with wired capabilities) Im going to wire the other 4 too a 2nd router so the cameras are always running and don't suffer any down time due to signal loss (happening a lot at the moment). How can I get Router B to talk to Router A, so I can look at all of the cameras from Laptop in my house which is closer to Router A.
My Router A is TL-WR1043ND, I'm also going to probably buy another one. How to configure it properly. So I can login to the cameras from my laptop.
View 1 Replies
View Related
Dec 28, 2012
Region : UnitedKingdom
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version :
ISP : blueyonder
I am having a problem connecting my router to my cable modem. I keep getting the check network status.
View 1 Replies
View Related
Apr 16, 2013
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I just bought and installed this wireless router, specifically so that I could use me kindle..but, keep getting rejected due to a password error...the password is correct. On Amazon it looks like there may be a setting that needs adjustment in order to accept the Kindle..
View 2 Replies
View Related
