Region : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
After my dir-655 recently bought the farm, I picked up a NIB 601 at a local computer mall for about $20. The drawback is that "local" for me means that the router is in Chinese.
Is there any way for the web interface language to be changed to English?
I have bought D-Link DIR-600 router from China and I want to change the web interface language to English.
-Router Info.
-firmware version: v1.03CN
-hardware version : A3
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP : Bezeq benleumi
I want to setup WDS using my TL-wr941nd WDS router?
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have two(2) WR941ND routers working at my home. The primary has IP : 192.168.1.2 , this primary router is working as an Acess Point, DHCP is OFF, and no wireless security activated. This primary router is connected to a DSL modem+router and DHCP is activated on it.For the secondary router I configred 192.168.1.100 . On the secondary router I have activated WDS function as well as Wireless Security (WPA2) , DHCP is Off on it. This secondary router is to work as wireless bridge + Access Point. You will understand that this secondary router is wirelessly connected to the primary one.I am able to configure all, and all things work correctly for few days at a time.But if at any time the secondary router is switched OFF, and then again switched ON, it seems to have lost al the settings and its IPs, and thus unable to connect to primary router. At such time I am unable to locate /connect my laptop to this secondary router, and it keeps on searching & searching.
Region : Canada
Model : TL-WR941ND
Hardware Version : V5
Firmware Version : wr941nv3_en_3_13_9_up(120201)
ISP : Teksavvy
This wireless router keeps freezing. It might stay up for 6 hours at the most, then I have to reset it or unplug for 10 seconds to get it to reset. I updated the firmware a few months ago thinking this would solve the problem. It hasn't.
Region : Greece
Model : TL-WR941ND
Hardware Version : V5
Firmware Version :
ISP :
Does TL-WR941ND provide support for 802.1x? (It is not mentioned in the product data sheet, but I found here: [URL] that it is supported on the above device.)
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
ISP : TDS
Currently I am using 2 WA5210Gs and a WR941ND to send my wireless connection from one home to another. The original home utilizes a TDS DSL modem/router combo. Everything works great, but then generally withing 24 hours I will randomly drop my internet connection in the second home, but the network is still up and running strong. The modem is not the problem, because I am able to grab a faint signal from the WA5210G AP connected to the modem and access the internet, and the client WA5210G AP is running at full signal. If I power down the router and restart it, the problem is fixed, but happens again within 24 hours. Originally I changed the IP on the WR941 thinking it was an IP conflict with the modem/router, but the problem occurred again. I also tried switching to unicast DHCP, but the problem still persisted. I looked for a firmware update, but couldn't find a newer version..
Region : UnitedStates
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : TL-WR941ND_V2_V3_120201
ISP : Cox
I updated my firmware due to connection issues, now it gets stuck when trying to load the console. I can see the grey pipe separators on the screen, but nothing else. I've tried chrome, firefox, and IE, but still nothing. The wireless AP is active, and i can connect wirelessly, and i can ping it. just cant get the console to show.
Region : Australia
Model : TL-WR941ND
Hardware Version : WR841N v8
Firmware Version : 3.13.27 Build 121101 Rel.38183n
Model : TD-W8968
Hardware Version: TD-W8968 v1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
I have two routers, a TP-Link TD-W8968 (main & connected to ADSL) and a TL-WR841N (client) and I'm trying to get WDS working over them in order to use my PS3/media player etc at the tv.
1) are these 2 pieces of hardware compatible for WDS? Status of both hardware seems to indicate yes
2) if compatible, what am I missing so devices behind the client router can access the internet connection.
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel. 54965n
ISP : Toya Lodz
This is already my second model of the router, which got under warranty. The first model had a problem because it brokes off Internet connections. This second model also breaks the connection. I'm going to give it to complain. Before I do it I would like to ask if there are any ways to improve the router without the need to dispose of the device.
Region : India
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.6
ISP :
We need to configure the AP in such a way, only 1 antenna to be used & not other two, to meet some mounting requirements/limitations. Will I be able to do this using any test/debug commands?
Essentially I want this AP to be operating in 1x1 spatial stream, & with no antenna diversity, so that I can connect only 1 antenna & be deterministic about AP using only connected Antenna RF port & not others
With out configuring anything, when I connect only 1 Antenna, I observed that signal is fluctuating on Client Application & causing the applications traffic stream disconnect.
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : Not Clear
Firmware Version : 3.6
ISP : comcast
what do i need to do to have my laptop access an Iomega EZ networked external hard drive? It is not my firewall on computer so Norton said it is the router.
Region : Singapore
Model : TL-WR941ND
Hardware Version : V3
I would like to connect a device (dataloger that sends data to a remote server via internet) which only has LAN port to a wireless network on the location. I managed to do this once with WA901ND configured in Client mode (WA901ND acts like a wireless card for this data loger).Does WR941ND support this feature (which feature should I use?) or should I buy WA901ND again?
Region : Others
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.13.9 Build 120201 Rel.54965n
We are trying to use a TL-WR941ND purchased about a month ago, but it keeps hanging, usually within a day or so of operation.To be clear: by "hanging" I mean the device stops providing wireless services (its SSID is no longer visible in WiFi clients) and becomes nonresponsive to pings or control access attempts (via settings web page) from the internal network connections.The device is used in a very simple scenario, where it's being employed as a simple access point, not as a router. As such, the device's configuration is as follows:
* WAN interface is configured with a dummy static IP (10.10.10.10/24) with gateway and DNS set to the internal IP address of the actual routing device connected to the external world.
* LAN interface is configured with an IP address inside the actual internal IP subnet (192.168.1.0/24).
* DHCP is also disabled as this service is already provided.
* Wireless settings: radio enabled, SSID broadcast enabled, WDS disabled, 11bgn mixed mode, auto channel width, max TX rate, channel 7 (manually set). Using WPA-PSK security.
Rest of the settings are unchanged from their default values, as the device isn't being used as an IP router by any client - just as a WiFi/Ethernet layer 2 bridge. We're using what appears to be TP-Link's latest stock firmware for the device.The settings described above appear to provide the connectivity required by the WiFi clients. However, the device continuously hangs within a day or so of operation, requiring someone to physically attend to the device and cold-restarting it (disconnecting it from power and reconnecting it) to regain an operational state.
After performing a cold restart, the system log shows nothing beyond the startup entries: "System started" entry followed by security info entries regarding enabled protocols. Then the device appears to work well for a while, until it hangs again, forcing again someone to attend to the device, etc.
Region : Poland
Model : TL-WR941ND
Hardware Version : V3
Firmware Version :
ISP :
I have a problem with files sharing via wi-fi. I can not share files over the network using wi-fi connections. While the network is the cable connection sharing is available. The network also acts as one computer is connected by a cable to the router and the other via wifi. But if the two computers are working through wifi network does not work. Are there any settings in the router, which can cause blocking calls via wifi?
Region : Hongkong
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?
Region : China
Model : TL-WR741N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am American living in China. My Chinese reading is not so good, I am still learning. The interface for my router comes up in Chinese. Is there a way to change the language to English? So far, all I can do is get the set-up interface through IE, but I can not set it up!
How can I change the language of the admin interface on a belkin wireless router (F7D2401) it all appears dutch.
View 2 Replies View Relatedi have D-LINK DIR-619L 300M Wireless Modem Router. its language is Chinese. i want to change the language to English.
View 1 Replies View RelatedFor some reason my E4200 keeps going back to Swedish (I'm in Sweden) even after I have manually set it to English and making sure to save the changes. What I'm talking about is the WEB interface reached by going to 192.168.1.1
Why does it do that and how can I make it stick to English without switching back to Swedish all the time by itself?
Region : UnitedKingdom
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : TL-WR1043ND_V1_120405
ISP : BT Infinity (1)
I have a TL-WR1043ND v1 with the latest firmware installed TL-WR1043ND_V1_120405.I loose access to the router (can't see web page, can't config, can't restart).I have a Linux server on the Ethernet, and uplink through 200Mbps powerline adapter to the BT Infinity modem. A few other devices on the wireless.The router works well and I prefer it to the BT Home Hub 3 for fiber because it proved to be faster in many cases as tested.But after a few days the web interface becomes inaccessible. It's like the web server died or something. Browser says connection reset, if I try telnet to port 80 says connection refused.Actually I just did a full netcat scan (sudo netcat -z -v -192.168.1.1 1-65535) and all ports say connection refused.Ping works - I can ping it allright.DHCP server works too, just restarted a computer and got IP from the router.Port forwarding works as well and DynDNS seems to work as well as my ISP changes the IP periodically and I can always find the updated one.All works - exept I can't access the router in any way!If I restart (remove power and plug it back in), it boots and I can access the router again.So restarting won't work remotely, I actually have to go home to re-plug it!
I'm just finished with the wizard of my WRT54GL and follow the instructions in my user's manual I enter in the Web-based Utility of the router but I was surprised when I see that the language is French?! Once I choose the language for the wizard - english, it was english but now the Web-based Utility is in French. For luck I know some French from the high school but I prefer to work with English. How to change the language of the Web-based Utility from French to English
View 9 Replies View RelatedRegion : UnitedStates
Model : TL-WR940N
Hardware Version : V1
Firmware Version : TL-WR940N_v1_120201
ISP :
Just bought a TL-WR940N and it was always loosing connection and freezing / locking up. I upgraded to the latest FW from the link below URL but it still freezes and loses connection to devices after 8-12 hours, keeps hanging up and pages sometime don't load.
I have a TP-Link (TL-WR941ND) wireless router in my living room and I want to expand my connectivity to get to the bedrooms area. I have a D-link (DI-524)wireless G router I want to take advantage of. How can I connect the two routers (no cables to be used) together so I can have acces to the internet from my room?
View 1 Replies View RelatedReceived a replacement DCS-930L today; using WPS, did setup wirelessly; all OK. Then did firmware update wirelessly (with second, DCS-932L, turned OFF). The v1.03 firmware file was the same one I previously used, I think. Amazingly, The camera menus are now in French, and I can't find a setting to change it to English.
View 1 Replies View RelatedRegion : Germany
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : 8.1
ISP : M-Net
I set up my router and it does not get a WAN IP.The PPPoE user/pw ist 100% correct but in the "status field" it always says: "connecting" and i can't get an IP.The router is connected with the modem via RJ45 cabel that was in the box.My PC has no problem getting to the internet with direct modem communication (pppoe).
Region : Others
Model : TL-WR841ND
Hardware Version : V7
Firmware Version :
ISP :
my ip address is not static i use no-ip sevice to get dns how to set my tp link for wake on lan
I managed to update ddns in my tp link How do I go from here?
I am currently running a TL-WR851ND Wifi Router whith the latest build 3.13.27 Build 121101 Rel.38183n() published last November 2012. Now is there any new firmware?
View 1 Replies View RelatedRegion : UnitedStates
Model : TL-WR940N
Hardware Version : Not Clear
Firmware Version : latest
ISP : Time-Warner
Just purchased the WR940N to use as a wireless bridge. I expected to be able to have the router join my wireless network, and provide Ethernet connectivity to 4 devices behind it. But I'm missing something in the configuration. I can get it on the wireless network, and manage it via the wireless network. But devices plugged into the Ethernet cannot get out to the Internet. Basically, I have a 192.168.1.x network, and the router is node 192.168.1.3 on the wireless network. I've turned off the firewall and DHCP on the router. The Ethernet devices behind it get an address from my network, but the router inserts its own address in as the default gateway, and my Ethernet devices do not have a route to my 192.168.1.x network, despite having an address on it.
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP :
I have a WR1043ND
Firmware Version:
3.13.12 Build 120405 Rel.33996n
Hardware Version:
WR1043ND v1 00000000
I tried to connect a WD MyBook Essential 3tb hdd NTFS, but it never recognized it. Of course, I connected it with the external power supply.With a 15gb pendrive FAT32 it works OK.
Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : Russia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : wr1043nv1_ru_3_13_10_up(120614)
ISP : netbynet
Connection to a router on a cable speed of dowstream-50MBit/s, upstream-3Kbit(!) wifi-dowstream-50MBit/s, upstream-3KbitA cable directly in the personal computer to 70 Mbps there and back.Measured speedtest.net, and as [URL] The matter is that even elementary with an investment it is impossible to send mail - I am connected by different devices-2 of the laptop and 2 smartphones - the same. Technical support of provider already talk sense only in a router. Insertions updated, changed - the same( Firewalls are disconnected, any more don't know what to do and where proceeding speed and all digs-is killed. Russian forum TP-Link is idle.
Region : Others
Model : TL-WR843ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I buy TL-WR843ND router to provide a better signal upstairs. Router is in wisp mode with statick ip. Everyting work good. I have routed home network with mikrotik. And everyting was setup with priority on mikrotik for each user separately. With this router every user connercted on it was hidden behind TL-WR843ND. How to disable NAT on TL-WR843ND to use routed network?
