For some reason my E4200 keeps going back to Swedish (I'm in Sweden) even after I have manually set it to English and making sure to save the changes. What I'm talking about is the WEB interface reached by going to 192.168.1.1
Why does it do that and how can I make it stick to English without switching back to Swedish all the time by itself?
I'm just finished with the wizard of my WRT54GL and follow the instructions in my user's manual I enter in the Web-based Utility of the router but I was surprised when I see that the language is French?! Once I choose the language for the wizard - english, it was english but now the Web-based Utility is in French. For luck I know some French from the high school but I prefer to work with English. How to change the language of the Web-based Utility from French to English
View 9 Replies View RelatedRegion : Hongkong
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?
Region : China
Model : TL-WR741N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am American living in China. My Chinese reading is not so good, I am still learning. The interface for my router comes up in Chinese. Is there a way to change the language to English? So far, all I can do is get the set-up interface through IE, but I can not set it up!
I have a problem with my EA4500. Router permanently rebooting. - router is not visible on the network. Ping to 192.168.1.1 - loss of all packets; - hard reset (30/30/30) does not work.
View 9 Replies View RelatedRegion : China
Model : TL-WR941ND
Hardware Version : Not Clear
Firmware Version :
ISP :
I bought a TP Link router to access internet. Nevertheless the routur interface is in Chinese language which is not convenient for me to set it up.How to change the interface language ? How to upgrade the routur interface to an english one ? (in the website I cannot see firmware for V6).
Would it be possible to change it to something else like serviio?
View 3 Replies View RelatedChanging the NAT Type 3 to NAT Yupe 2 or 1 because I can't play with some of my friends on Playstation3
my router is: Cisco E4200
Is it possible to change the Guest Network Name on the E4200? And if so, is it possible to do so without having to do a complete reset of the router and without using the Cisco Connect software?
View 4 Replies View RelatedAfter my dir-655 recently bought the farm, I picked up a NIB 601 at a local computer mall for about $20. The drawback is that "local" for me means that the router is in Chinese.
Is there any way for the web interface language to be changed to English?
I just bought a E4200, is there a way change the default text of the pop up message that is used when the client is requested to put in the password to access the guest SID for the e4200?
View 2 Replies View RelatedI have bought D-Link DIR-600 router from China and I want to change the web interface language to English.
-Router Info.
-firmware version: v1.03CN
-hardware version : A3
I was changing some settings on the router, disabled the WMM QoS, and I can no longer see either the 2.4 or 5GHz networks. I power cycled, tried resetting to defaults but the wireless seems to be dead. I can manage it wired, but that does me no good.
View 2 Replies View Relatedi have D-LINK DIR-619L 300M Wireless Modem Router. its language is Chinese. i want to change the language to English.
View 1 Replies View RelatedHow can I change the language of the admin interface on a belkin wireless router (F7D2401) it all appears dutch.
View 2 Replies View RelatedI use a WPC54G wireless adaptor to connect a laptop to my home network. I just replaced a WRT54G2 router with a Cisco Valet router.When I start up the laptop, the wireless adaptor's Monitor configuration takes priority over Windows XP wireless configuration, but the Cisco Valet does not recognize the Monitor. If I disable the Monitor, everything is fine until I reboot, and then the Monitor again prevents connecting to the router.
How do I permanently disable the Monitor software so that the laptop will default to the Windows XP wireless configuration settings?
My WAG160N had been working fairly reliably until this morning.
It's now stuck in a permanent cycle of resets:-
1. Power lights flashes 10 secs
2. Then wireless light comes on for 5 secs then goes out
3. The 4 network port lights flash once
4. Then just power light comes on for 2 secs
5. Power light blinks red, and repeat...
I've tried powering off (router and anything trying to connect), & unplugging everything. No difference.
Also tried the reset button. This seems to work - power light goes red after about 5 secs, and the router restarts. But no improvement.
It's not even staying up long enough to connect to the admin page.
I just switched ISP's and they provided me with a Ubee router. The computer plugged directly into works fine, great speed, no drops. A laptop connected via Wifi is the same, great speed, no drops.My Router is not simply 'dropping' connection, but instead, 'disabling' the internet to the devices and forcing me to reconnect in order to get approx. a few minutes of it again.I have a Desktop computer with a WGA600N Gaming adapter hooked up to it, and an iPod touch.Both worked perfectly with the old router, so I know it's the router for sure. The thing is, it's not just dropping and reconnecting..
It's connecting for a few minutes, and disconnecting permanently until I reconnect to the connection..For my iPod, it doesn't actually disconnect me, I just lose internet. It says I still have 3 bars of signal strength on my iPod, but I don't have internet. I must hit 'Forget this Network' and retype the password in order to get another 2-3 minutes out of the signal.As for my Desktop hooked up with the gaming adapter, when the internet 'runs out', I simply unplug it and plug it back in to 'renew' the internet.
What are the steps to turn on wireless capability permanently?
View 1 Replies View RelatedI have just connected a Cisco 2600 series router with a rolled over cable one port ( RJ-45 connector) in my console port and serial port in my PC COM1 port. Now when i open tera term and want to type something, the router is showing stange language.
View 13 Replies View RelatedI have a recurring issue with my e4200v1. My wired and wireless connections work fine, but I can't get to the administration website. I have https only set up, and after I get thru the 'certificate error' screen, I get an error that says web page is unavailable. Firfefox tells me that the connection was lost - error 101.I have tried wired and wireless, multiple computers, multiple browsers. I even turned the firewall off on one computer (or I think I did anyway).The only way I know how to fix it is by completely resetting then setting up the router all over again.
View 2 Replies View RelatedUpgraded from WRT610N to E4200. Since upgrading to latest firmware the wan just disappears both 5 and 2.5 Ghz bands. Happened with older firmware but not as often. Using it in briged mode. When this happens I can't even get to the management page with a lan connected pc. Have to do a hard reboot to get it to respond again. This is unacceptable for a router at this price point.
View 2 Replies View RelatedI want to know how to change the Router Password. I have two computers running XP connected to my WRT54G; one via cable and the other wirelessly. I'm using WEP security. The router setup defaulted to "admin" for the Router Password; I'd like to make it a stronger password.
View 9 Replies View RelatedA few months ago, I purchase, installed and configured a WRT 160N V3. And I couldn't be happier. I now would like to go back and change the passphrase that a user needs to enter when they connecting to my router. Currently it uses the default value. And I would like to make it a bit more friendly. I found a number of postings dealing with setting retrieving or changing the Admin password.
But I was not able to find anything on changing the “passphrase”. There probably are a number of postings on the subject, and I simply overlooked them.
I cannot find the screen in the interface at 192. Where is this? Please don't say use Cisco Connect disc.
View 1 Replies View RelatedHow do I change the tcp timeout on a WRT54GS router v2 ?
View 4 Replies View RelatedHow do I change the IP address on the router?
View 1 Replies View RelatedHow do I change my wireless router's (WRT54G) external IP address? I'm having IP conflicts with Yahoo and whenever I check the router's IP, it's always the same, despite the fact that my cable Internet provider uses DHCP to hand out IPs.
View 4 Replies View RelatedChange the channel on my router WRT160n?
View 2 Replies View Relatedchanging my nat type to open i have tryed so many solutions and none of them worked?
View 9 Replies View RelatedI want to change my old router (wrt160N v3), by this model Linksys E2500.The question is, there will be a lot of changes improvements if i do this upgrade?
View 2 Replies View RelatedI dont know or understand how to change my nat type. I have the e3000 linksys router. My ps3 is running wireless off it. I want to change form nat 3 to 2
View 1 Replies View RelatedI have a couple of Linksys WRT54GS V7 routers, they work fine, with the exception that when I login to the web interface, I select the drop down box for DHCP to change it to a static IP, the page refreshes, but comes right back to the same screen with DHCP selected again, I can change the time zone with no issues, I entered the Static DNS info. I've tried a couple of different PC's with a couple of different IE versions. I already updated to the newest firmware, firmware is 7.50.8, I've also factory reset it a couple of times, and I've just run into a brick wall. I've setup hundreds of these routers before so it's not like I don't know how.
View 3 Replies View Related