My USB Belkin Wireless G Network Adapter seems to disconnect whenever I remove another USB device (usually a memory stick) from the PC.The problem started when I accidentally updated the driver via Windows. It didn't seem to work at all with this updated driver and I couldn't roll back or do a system restore to fix it. I'd done this before and ended up doing a complete re-install of Win 7. This time I did an upgrade install and the driver problem was cured.I'm running a HP XW8400 with Win 7 64 Pro which has been faultless for the 5 years I've had it.The only other change I've made recently is that I've stopped using a D-Link USB hub and started using the USB connectors on the HP LP2465 monitor.This only affects the wireless and no other USB devices.
When it disconnects, Win troubleshooting goes through the motions and reverts to LAN and doesn't see the wireless USB at all. This also happens if I don't use the troubleshooter.Device manager shows the driver to be working, but the wireless USB doesn't function even if I connect it directly to a USB port.The router is still working as all other devices in the house are connected.The only way around it seems to be a re-boot, but when this fault happens the PC gets stuck at "Shutting Down". Without the fault, re-boot or shut down works fine.When it happens I have to power off and on. This usually works fine but every now and then I notice the device driver for the Belkin is disabled.I've found a workaround in that I can take out the Belkin USB before removing another USB device. After the USB stick or whatever is removed if I then reconnect the wireless USB it reconnects fine.
"disconnect" home network from VPN tunnel to business location due to close of business. We had a business network that we could access from home. We've lost access to the business network, and it seems logical that we should be able to use the home network that is existing, but was fed internet from the office, and "re-direct " it to read just the home network.Currently at home we have a windows XP cmptr with a Netgear router, wireless access box, and Bell South Westell DSL box. How to we basically cut off the VPN link and just get what we have to read the home network?
I currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
Two switches, which are not configured for SSH and snmvp3, were picked up during an discovery and automatically added to the DCR. When I view the list of devices in the DCR the two devices are shown, but when I try to edit the DCR to remove/delete the two devices they are no where to be found.
I just got this av to cat5 converter [URL]? and was thinking i could use a router on each end so it could be wireless. But the way they work the router does not see the converter when it is plugged in.
I recently upgraded my wireless router from D-Link DIR-615 to D-Link DIR-685. Before the changeover, all of my devices were connecting to the router, although I had several problems with dropped connections, etc. The devices in use were:
- Desktop computer - Laptop computer - All-in-one touchscreen computer - Netbook - iPhone (original model) - HP TouchPad tablet - Sony Blu-Ray player - Two internet radios (Aluratek and Livio) - Wii
ALL of these devices were connected wirelessly to the network. When I set up the new router, I used a different network name/SSID, but kept the same security key/password. All of the router settings were kept the same (e.g., WPA-2, etc.). After the new router was up and running, every single one of the devices listed above connected (after an initial setup with the new network name, of course) EXCEPT the All-in-one/touchscreen computer. I've tried over and over, and it refuses to accept the security key/password. (The desktop, laptop, and touchscreen are all running Windows 7 64-bit Home Premium.) After doing some research, I tried some suggested solutions, but nothing seems to work. Nothing on the problem computer has changed since it was last connected to the old router. I checked the "Properties" of the network device on both the Desktop (which has no problems connecting) and the Touchscreen, and they are identical: WPA-2, AES, etc. And I'm 100% positive I'm entering the security key correctly. I've rebooted the router and the computer several times.
I have a video conferencing device that uses a lot of ports and is very bandwidth intensive. I have been messing around with two routers (cheap ISP Thomson and my Netgear DGND3300v2) settings for a couple of months now and I couldn't get it to work properly (ports were getting blocked randomly). I have recently discovered that Netgear has a "secret" page where you can switch the router to a modem mode. I gave the device a public IP and now it works fine (at least so it seems for now). The thing is, I need to connect another device (my PC) to the device via web interface for monitoring purposes. I am wondering what network arrangement would be best for me. I want the video device to have nothing to do with natting or firewalls at all, I want it to have a public IP. However, I also want to be able to connect to it somehow and also share the connection with my PC.
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
Does a 802.11g compatible device on a 802.11n network slow the whole network down to 802.11g speed?I want to integrate a Logitech Squeezebox into my 802.11n home network but it is only rated at 802.11g.
recently I've connected to my OpenVPN and everything works fine on my PC I'm getting okay speeds and the VPN IP appears on [URL]The problem is I wanna use internet connection sharing to play Xbox Live while connected through my VPN and I'm having issues.My Xbox isn't even recognizing my wired connection.This is the setup:Wireless Connection > Desktop > OpenVPN > Wired connection from desktop to XboxWhat I think I'm doing wrong is not specifying the correct home networking connection for my LAN 3 (Tap-Win32 Adapter OAS)I tried sharing the LAN 3 connection and set the home networking connection to my Wireless and it disconnects me from my wireless network.
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address - The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address - The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
i am finding an ip address which is some hardware laptop or something that has got that ip from our doimain network while connected to our network. I dont know who it is and what it is and i always use Advanced Ip scanner and shut down any pcs manually with it and search for illegal hardwares connected to our lan but thisone is unable to be turned off it says unsuccessfull.Is there any software that allows me to kick out hardwares from our domain network?
Ive just updated my hardware including hard drves, and now I have a couple of redundant shared folders showing on the network trees (in my file manager) How do I delete these obsolete shared folders that dont exist?
I've been noticing a Belkin router on my network for a while now and just yesterday another Linksys router as join the party, causing havoc on my connection speed!
The strange thing is that I'm the only one seeing them through Norton on my laptop, all other computer on my home network is not detecting them. could this mean that someone is monitoring me? is possible? If I move permanently to Ubuntu linux would the problem go away? OR will they still be able to connect and monitor me?
How do I audit a network PC to see what it has on it or delete what does not need to be there. If I do it through the Windows add or remove they re-install. In the old days I could do it in DOS and then 'Tree' to list the properties and then delete what I wanted permanently.
i have a computer that is on my home network that i am trying to disable. the person no longer lives with us and it is still showing that there computer is connected to our WiFi ? our internet provider is At&t.
another computer is connected to my home network, and i want to remove them as i don't know who it is. I also notice my files have been very recently shared within the 'homegroup'. i have not personally done this.is someone accessing my computer?
I currently use Pure network majic as my network manager but on my desktop zoom network manager is installed and will not allow PN to do its job. I have gone through my desktop with a fine tooth comb to find this file/application to no avail. I don't remember installing it, bit I need to get it off.I have the same problem:The previous reply was Did you look for it inside the Control Panel under "Add/Remove Programs"? Is there anyway to get rid of it? Is there a process that is running when it is running and what is the name of the process?
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
I have been having a bit of trouble with networking my two machines to share files and allow printing i have a win 7 laptop and a xp home desktop. I share a net connection via 02 wireless box both systems have wireless i have tried many things
Every time I connect to my home network with iPhone 4 my whole network stops working. Windows 7 is not reporting any problems with connection, nor is my router. I have cable connection with my PC and wireless with my laptop, they both just stop working without any visible reason. Even the iphone i connect with wont work, but of course it says its connected and everything is ok.I tought it was an iOS 5 problem, so I reinstalled it. It worked for an hour then its all back again. I even tried sharing my PC conection so that my iPhone is connected to PC and not directly to router.But that produced the same results.
My Set up at home is as follows: [code] Now according to what I have read I should be able to set the subnet on .2.0 network to a subnet of 254 and this gives me 512 Hosts I believe however my question at this point is how to route between 192.168.1.0 and 192.168.2.0.Or when I set the subnet .254 does the router just route it automatically.I would still set the subnet mask on both networks to 254 correct? I believe I can only use 192.168.0.1 to 192.168.1.255 w/.254 subnet mask. However I already have some servers that are configured with applications (On the 192.168.2.0 network) that I do not want to change ips on because it would be a pain to reconfigure so, my other question is other than using .252 to extend it to 192.168.0.1 to 192.168.3.255, (I need the 192.168.2.0) is there anything I can do? Like use 192.168.1.0 with subnet mask of 255.255.254.0 to get the 192.168.2.0 network? The reason I asked is I was using a subnet calculator to try and figure this out but every time I put in 192.168.1.0 with .254 subnet mask it changed the ip to 192.168.0.1 to 192. 168. 1. 255.I would really like to use the netgear only. The way I have it now is not working I am able to ping the internet from the 192.168.1.0 network but I can't ping from 192.168.2.0 network to the 192.168.1.0 network.