I'm working with two Catalyst 2960 switches and I would like to know if there is a way to monitor bandwidth on individual ports. Ideally I would like to have one graph showing a bandwidth usage reading on each port. I tried using the Network Assistant to accomplish this, but I was only able to view one port at a time. I also tried using a traffic graphing program from Paessler, but a MIB file is needed to allow the program to connect to the switch. When I ran a search on the network management page the 2960 was not on the list for MIB supported products. Is this type of graph possible to do?
I want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
I was wondering if there is a way to monitor the total bandwidth available at any given time? My ISP claims and is charging me for a certain amount of bandwidth but I suspect that during the day I am getting much less.
I would like to track available bandwidth continuously (or every 5, 10, 15 minutes) and log that data so I can show them the results. I'm on a Mac 10.7 but can use Windows XP also.
I have a Cisco 1184 with Hwic 1-t (IOS 12.4(15)T12 ). i want monitoring average load of my HDSL. How to can i monitoring my bandwith in upload and in download for WAN interface ?
Does the SGE2000 supports NetFlow? I've checked the Cisco docs and also called Cisco support to which no one has been able to answer me.
Anyhow, just in case it doesn't support NetFlow, how to be able to set up something that would be able to check the bandwidth usage on each port?
I've got a problem where I think the SGE2000 switch is failing when I pump around 190~200Mbps through x2 of the ports (Server A on port 1=130Mbps and Server B on port 2=60Mbps) of Multicast traffic (UDP). I can measure the output from the Streaming servers that provide the multicast content, thats how I know the input to the switch and I know that there are no packets lost or any errors departing from the servers, yet when I increase server B to say 80Mbps, I get break up and all sorts of problems on the client end STBs and it is happening on the multicast content provided by Server A too which is a different source, so I'm 99.9% sure its a SGE2000 switch problem which is why I'd like to monitor it somehow.
We have a Cisco ASA 5520 supporting multiple VPNs - both remote-access and Lan-to-Lan. We would like to monitor the bandwidth utilization of the IPSec Lan-to-Lan tunnels.
I am using ASA 5510 Firewall and i have established VPN tunnels too , now i want to Monitor the bandwidth utilization , i have installed PRTG Monitor application and want to add the firewall , how to enable the SNMP in ASA .
I have a ea4500 router with 3 pc's, 4 iphones, 2 playstations, ipad, ps vita, house cat, and a printer all wired into the internet. There are four of us in the family all using the internet but I suspect one of us is using considerably more than the other. I live in the country and my current isp has us on the max available account - 50 gigs / month. Lately we have been hitting 45 in less than 3 weeks into the month. I would like to know which of the things connected or which person is using the most of the bandwidth up. Is there a program that doesn't require a phd in quantum physics and networking that can monitor this for me and spit out a report.
I'm a C# programmer and as part of my software I need to monitor some Cisco Catalyst 3560V2 24 switches using SNMP (By reading MIB/S data).Apparently this switch supports more than 50 different MIBs.My question is which MIB/MIBS contains general health data (parameters) that may determine if the switch is OK, Degraded or Malfunctioned.
In s SPAN session , normally the destination prt is used for monitoring purpose only. But could destination port be used to access the equipement or PC connected to that port , for a 2960 LAN BASE image switch .
I am looking to simply monitor Port-Security , Error-Disable and HSRP. I would like to receive an email when any of these are triggered.
Port Security - Port Is shut down Err-Disable - Port goes into err-disable state (securedown) HSRP - When HSRP standyby changes are detected
I need to receive emails with any of the able are triggered. What is the easiest way to do this? I know SNMP is the main option but I have never worked with SNMP and dont understand it too much.
We are looking at putting in a solution at a hotel for Free Guest WiFI.The solution would cover 4 floors and about 120 rooms and some open areas .In short the hardware would look as follows
-2500 controller -1142LAP -2960 PoE switch -878 Adsl router for internet connectivity (20Mbps/1Mbps internet ADSL feed)
One of the concerns raised by the client is that they would like to make sure that no single user could eat up too much bandwidth creating problems for the rest of the users . Can the above KIT or something similar achieve this objective? As far as I can think of we would require a Proxy server .
I've just made a purchase for a Cisco 2960 8 port switch ( Exact model: WS-C2960PD-8TT-L ), I reckon this is what I need to set up my network, so far I've gone through the Express Set-up and configured it through there with no problems. I've set up the hardware in the following manner:
-Internet Modem >Port 8 on Switch ->Port 1 on Switch goes to 1252 Cisco AP ->Port 2 on Switch goes to Linksys VOIP home Router
I let it start up and can connect to the internet through the AP, and through the router. (I'm posting through the AP-Switch set-up right now.) However, once I connect to the AP with a second client. It refuses to let the second client connect/not give an internet connection, as it would a direct connection to the modem.I'm going to assume this is due to NAT not being configured through the command line on the switch yet.
I have two Catalyst 3560 series switches with a 100Mb Ethernet microwave link and a 250Mb Ethernet microwave link between them. Can the switches be set up to make full use of the added bandwidth (350 Mb).
I have a problem with radius authentication on catalyst 2960 with freeradius as radius-server. The Catalyst is behind a HP5412zl layer3-switch. The rest of the network are hp-layer2 switches, which do radius authentication to the same radius server. The ios on the catalyst is c2960-lanbasek9-mz.150-1.SE3. Apparently there are no requests made to the radius-server, since I dont see any requests coming in. Port 0/7 is voice port with laptop behind , /port 0/8 access-port with laptop directly connected.
On my country, international bandwidth still expensive. I want to split local and international bandwidth and limit inbound and outbound bandwidth for each ip like this:
IP 10.100.10.11 can use 100Mbps local bandwidth, 1Mbps international bandwidth
IP 10.100.10.12 can use 100Mbps local bandwidth, 2Mbps international bandwidth
I want to use
Router 3825Switch 2960 NB: I have online one internet line.
Was the above equipment can perform functions that I want or need any additional equipment? And Should i use 2 line to achieve my goal?
I'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
I would like to be able to query the dot1dStpPortState obect on the Catalyst 2960-S on our LAN . Im running firmware c2960s-universalk9-mz.122-55.SE2.bin and according to the Cisco SNMP Object Navigator the object is supported (via the BRIDGE-MIB).However when i query using snmpwalk from my workstation :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 I receive and error .SNMPv2-SMI::mib-2.17.2.15.1.3 = No Such Instance currently exists at this OID For the sake of comparison, querying our 4700 :snmpwalk -v 2c -c bic-zua-ro 10.u.y.x 1.3.6.1.2.1.17.2.15.1.3 returns (as expected, cropped)
Is there some special configuration i need to do on our 2960's. The only snmp related settings i can see in the running config is snmp-server community. In this case :
I try to add a Catalyst 2960 to Cisco Network Assistant, I get the prompt for password but I get a "Authentication failed". I use the same login / password for telnet that works fine. Http admin page is reachable but I cannot login with the "admin" account.
I have a device that does ip audio on one mac address and managagement is on another mac address. Both of these mac addresses come from one NIC on the device. We need to split these two traffic paths into two different vlans.How can I program this switch to sperate the different traffic into two vlan's based on mac address on one interface?
I have Catalyst 2960 S (WS-C2960S-48FPS-L) Switch. I have plugged in SFP module but still interface is down and line protocol down. Is there any configuration to enable SFP module and make the interface up?
i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin" admin@192.168.251.1's password: Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
Since I updated a Catalyst 2960 switch to IOS version 12.2(55)SE1 I can't do searchs by MAC address, when I do "Monitor->Search" the following error appears:"The software version of the selected switch does not support some of the CLI commands in read-only mode for this window. You must have read-write access to this switch to display complete information in this window" If packets are captured you can see that the issued command by the CNA host is "GET /exec/show/mac-address-table/", the answer from the switch is:"show mac-address-table ^% Invalid input detected at '^' marker.
If I do "Configure->Switching->MAC Address" instead I get the mac address-table correctly. In this case the issued command is "GET /exec/show/mac/address-table/dynamic" and no error is displayed, the answer from the switch is the list of mac-address table.
