Cisco :: AP802GN - Broken Web Management
Jan 30, 2013
I recently upgraded an AP802GN-E-K9 to version 15.2(2)JB (ap802-k9w7-mx.152-2.JB), which broke the web interface. The http server is still running, however the web interface is not available. The following is displayed instead Navigating to /ap_home.shtml etc shows the correct pages. Extracting the "tar" file from the Cisco site and looking in the /html/level/15/ directory in both the tar and flash shows files missing that I'd expect to exist ( frameHome.html , navHome.html etc ).
Alas, I have no SmartNet on this device (embeded into my 887VA-W) as it's for home
View 2 Replies
ADVERTISEMENT
Mar 22, 2013
I have a cisco router 2612 where NAT is defined ip nat inside source static tcp 192.168.1.63 80 175.x.x.x 80 extendable It appears that after sometime (may be in few hours) the NAT is broken and I no longer can access the server over port 80 externally.
View 3 Replies
View Related
Aug 21, 2011
I turned unplugged it and plugged it back in. Now its blinking green power LED. Is it dead?
View 2 Replies
View Related
Apr 26, 2011
Broken Pat/Overload after upgrade from 1711 to 891
View 7 Replies
View Related
Sep 15, 2011
I have searched the forums and found that there have been others with the same problem as me,but none of the solution offered was working for me so I decided to start this thread.I have an Acer laptop that wont recognize my ethernet cable, it says that there is no cable connected.
View 1 Replies
View Related
Jan 24, 2013
I can't find the problem in firewall..
View 3 Replies
View Related
Jan 20, 2012
Yesterday I was on my toshiba satelite L550-OCD and the wireless wasn't working then it started working again. I closed my laptop and when I went back to it it wasn't working again and hasn't since. It says there's no wireless connection to plug in Ethernet cable now I have tried Fn F8 and it doesn't do anything. So I went into my toshiba assist and opened optimize. Then toshiba hardware settings and clicked LAN and it says it's turned on. But when I click radar it shows it is not connected and the light is off.
View 6 Replies
View Related
Dec 1, 2012
I recently swapped a router out for an old one to check an internet problem (to rule it out basically) and when I tried swapping the newer (better) one back in it networks fine (ie computers can see/stream off each other) but it doesnt recognize as being plugged into the internet.
After doing a factory reset via routerlogin.net I still have the same problem. The only thing I can think of is maybe the port got damaged? (The ethernet cables all work fine).
My process for hooking up the new router in case I was doing something wrong:
Unplug cable modem power, swap all the cords, on router while cable modem was rebooting and then once modem connected I turn on router. Did I need to restart the PC as well? Is that why this is screwing up?
View 2 Replies
View Related
Feb 23, 2011
i have already installed this, but it stop working so i unplugged it, now cant find the CD
View 1 Replies
View Related
Jun 22, 2012
I have a WLC5508 and 25 LAP 1041. I use two wifi, one with RADIUS for data and other with wpa-psk for voip. The problem is the voip conectivity is broken.How can i improve the handover?
View 11 Replies
View Related
May 14, 2013
This feature is not working on our LMS installation. I have tried different browsers but is always giving the same error. It seems to be Java related.
View 0 Replies
View Related
Oct 3, 2012
I can't seem to reset my switch and realized the reset button is missing/broken off. Is there an alternate method to reset the switch to factory settings? If not, how do I figure out the IP of the web interface, it is not the default.
View 8 Replies
View Related
Oct 9, 2011
Currently we do not have multicat routing enabled on either of our 2x Sup720-10G 6509 Switches. We have no intention of doing so either. I am looking for clarification on how mutlicasting operates within a Vlan.
IOS: s72033-ipservicesk9_wan-mz.122-33.SXH2a.bin
Our Vlan has IGMP snooping enabled. Here is the output.
6509Switch#sh ip igmp inter vlan 25
Vlan25 is up, line protocol is up
Internet address is 10.1.1.254/24
IGMP is disabled on interface
we do not want to disable IGMP due to this one concern that I can't find documented. If we disable IGMP snooping on the vlan, what happens to multicast packets with a TTL > 1. Do they get flooded to the entire switch and all Vlans? Or does it stay within the Vlan?
View 2 Replies
View Related
Oct 23, 2010
I have tried to upgrade from 2.0.2.1 ever since 2.0.3.3 was released back in July. The firmware image file has remained the same, so I don't think they've ever changed it from the original July release.The download and installation go fine, I even reset to factory defaults. The problem is that several menu selections are broken, and don't allow you to save your choices, i.e, you can't even rename your SSID. You can type it in a Apply, but the fields just reset. I figured this would be fixed with a minor update to 2.0.3.3, but we are now several months since original release and nothing has changed. I have tried this firmware at least three times now. I have not bothered lately, because I don't want to waste another 30 minutes trying it and reverting back to 2.0.2.1 if this newest firmware is not going to work.
View 3 Replies
View Related
Aug 10, 2012
I have an acer aspire 5552 laptop that wont connect to the internet. When I tried troubleshooting I get the message "network cable not properly plugged in or may be broken". When I go through the control panel/system devices/network adapter the only thing that shows is pdanet. Right now the only way I can connect is through my cell phone using pdanet. How can I get my network adapters to show back up?
View 1 Replies
View Related
Oct 27, 2011
Same problem on Dell Inspiron 530. Thinking about inserting a new network card.
View 3 Replies
View Related
Aug 26, 2012
I have a new wireless router (new network, entirely). I used to get intermittent "network access denied" messages. Now, I get intermittent connectivity loss: "No internet access." I typically just right click and troubleshoot. The problem is solved and I get the following message: "Problem with wireless adapter or access point." Once fixed, things go on well for a random time (never more then a day). Then, however, they just fall apart.
View 9 Replies
View Related
Mar 15, 2012
We can not get on line with our home computer (dial-up). The computer dials out, the modem at our ISP picks up and then hangs up - Error 720.[code] The last two were installed by Avira Antivirus, a program which we have uninstalled.Can I download support files for a network adapter? Windows XP SP3
View 3 Replies
View Related
Feb 25, 2011
For about two months now I have been experiencing a problem with my Internet connection. It started when I upgraded my Dell Inspiron 530s from 64 bit Vista to 64 bit Windows 7. After a day, I started getting the "Local Area Connection: A network cable is unplugged or broken internet connection." However, the cable is not unplugged. My other PC and laptop (which is wireless) can connect to the Internet, so I know it's not my ISP or my router. It only happens about every other day. It would work perfectly on day and other day I would go to my internet and I would have no connection. The weird thing is that when I restart my computer, it connects right away. My other two computers that was upgraded also does not have this problem.
First, I thought it may be the cable, so I replaced it with another cable I had. No luck.Then I thought it may be the port on the router, so I plugged it into one of the other ports (including the port that the working PC was plugged into). Next, I checked Device Manager > Network Adapters > Intel(R) 8256v-2 10/100 Connection. There is no exclamation point next to it. Plus, under Properties, it indicates that this device is working properly.I shut down all my computers, and unplugged the dsl modem and router. I waited a few minutes and then plugged in the modem, followed by the router. Once both of those were fully booted, I turned my computers back on. Still after a few hours, I lost connection.Following this, I went to Run, typed "cmd" and then "ipconfig." Under Windows IP Configuration, it reads:"Ethernet adapter Local Area Connection: Media State.........: Media Disconnected."
View 16 Replies
View Related
Mar 7, 2013
I have a TAC case open, but it doesn't seem to be making any progress.I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0..Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.An interesting thing, on the 602 AP, in the log, I see this:*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled..So the AP is definately talking to the WLC and being pushed the correct WLAN profile.On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
View 6 Replies
View Related
Sep 19, 2012
Before upgrading to 8.4(4)1 I was able to ping our inside interface accross the VPN. Now I cannot. Because ping is not working, my SNMP server thinks that the device is offline however I know the VPN tunnel is still up and the remote branch office is working fine. Here is the config of the branch office ASA 5505 in question. How to get icmp working again?
ASA Version 8.4(4)1
!
hostname BranchASA5505
domain-name houston.deh
[Code].....
View 2 Replies
View Related
Dec 13, 2012
I have been using WAP4401N for almost a year in our office and I’m very happy of this device, never had any problem. So I bought 3 new ones for our customer which supposed to work in configuration below:
Network ----- AP1 –Bridge mode ----- AP2 – Bridge mode -----AP3 – Access Point mode.
Everything was working perfectly fine to the moment than bridge was broken. I can get access to all AP (obviously when connected to proper part of network) however not able to ping from AP2 -> AP1 or opposite so basically no link between AP1 and AP2. After reboot everything is working fine to next time (happens twice in two days). When I go to System Performance can see Connection is enabled but doesn’t work.
I upgraded firmware to latest version (2.0.5.3) but haven’t worked. When I’ve done some research found many users having similar problem with this device and basically they recommend to don’t buy. Unfortunately this is not an option for me as I’ve already purchased them.
View 6 Replies
View Related
May 3, 2012
I installed firmware version 1.2.0.9 a couple weeks ago after seeing in the release notes that the port forwarding bug where clients would get 'no route to host' was resolved (one of the original posts found here:URL
After installing the firmware and confirming it's running I've seen no improvement. I still must reboot my router 2-3 times daily so clients can access the ports that are defined in the port forwarding module.
View 23 Replies
View Related
Jul 24, 2012
I need to add some rules to block some attacks. I can add them fine but they get added to the end of the list. I try to re-order the rules to put them at the top and can not. I am using Internet Exploder 8 and I put a checkmark on the rule I want to move then click the reorder button. It takes me to a screen that shows 0 rules. I click the Back button and am back at the list of rules on that page. I am running the latest firmware which is from a year ago.
View 3 Replies
View Related
Dec 13, 2011
I'm running into several issues with certain .AVI files I've been downloading from MegaUpload, happening on two computers.Upon download of the video, Windows Media Player won't play it, Media Player Classic brings up AVI Chunk Viewer instead of playing it, and VLC offers to fix it but only manages to make a few seconds of it play (out of ~15 minutes).I can open it in VirtualDub and export as AVI, but the quality becomes ruined. Several multicolored glitchy looking boxes cover a lot of the screen periodically which wouldn't normally be there. This shows up before export as well.
View 1 Replies
View Related
May 30, 2012
My laptop's wireless network adapter is not working Eventually I managed to re install the driver but that did absolutely nothing and now it won't connect unless I have the ethernet cable plugged in. It also no longer will tell me there is a problem with the adapter, it just refuses to bring up any wireless connections. My laptop is a Dell N5110.
View 1 Replies
View Related
Jul 12, 2011
One of our ethernet CAT5e is cut off (broken). Now I want to join them instead of putting new cable and doing thing all over again as it is too long.
View 2 Replies
View Related
Sep 30, 2012
Generally works on wireless Guest network. Only allows one IP on wired or wireless. Using latest cloud firmware.
Instead of giving out the 192.168.1.100-150 as configured. It will give out from the cable modem (i think) 192.168.100.x
Seting static IP on computers works fine.
View 9 Replies
View Related
Nov 30, 2011
I cant get a connection to the internet when i open up lan theres a red x when i diagnose lan it says to plug in ethernet cable ive done that but then it says it may be unplugged or broken i even changed the ethernet cable but same problem, so i figured its the driver but that says upto date however when i reinstall it says theres no network adapter installed, i havent installed anything recently and to besure it wasnt because of an microsoft update i even did a system restore
View 12 Replies
View Related
Jun 6, 2012
Laptop does not work and wondering if there is any way to access the hard drive using my desktop
View 2 Replies
View Related
May 15, 2010
Upgrading the firmware from 1.11EU to 1.21EU and 1.31EU has introduced a problem with multicast (IPTV) streams. I have enabled multicast streams and it seems the router no longer forwards a specific address range, in my case 239.139.128.* on port 1234.
I have checked: Streaming from 233.81.233.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 24.1.3.* works in 1.11EU, 1.21EU and 1.31EUStreaming from 239.139.128.* works only in 1.11EUUsing IGMP proxy on Linux I have checked the stream at 239.139.128.* are available as to be sure the DIR-655 is not forwarding them. I see a lot of forum messages stating IPTV streaming is broken since firmware 1.11. It is however working for me in 1.31EU but only for certain address ranges. Can anything be configured to allow 239.139.128.* to work? Because my TV provider uses the 239.139.128.* range for half the IPTV channels I need to get this working.
Related to this, is there page listing known bugs for the DIR-655 and roadmap for future firmware releases?
View 2 Replies
View Related
Sep 27, 2012
I recently "uninstalled" DD-WRT from my router and tried to install the actual firmware for the router, so I went to this page [URL] WRT54G and select version 5. My router is really version 5.1 but I read on this forum that this router works with version 5 so I downloaded it and installed it.
However, this is how my admin page looks like,
And I can't do anything at all. Is there a fix for this? Is there an actual version 5.1 firmware? Or must I switch to a different, proper router?
View 8 Replies
View Related
Nov 17, 2011
I have a problem with e4200. Buy it about 1 month ago with firmware 1002, link to ISP by simple LAN with DHCP IP lising without any method of identification like PPOE or other. 2 days ago tech support of ISP call me nd say that my router send bad packet to their hardware and all LAN collups include DNS server. I disconnect all device from router but same thing happened. I update firware to 1003 but this action work for 1 day, and again tech support call me. What wrong with router or may be with ISP technician's hands?
View 3 Replies
View Related
