Cisco WAN :: 1800 Series Router Configuration?

Jun 9, 2013

load balancing and automatic failover between two isp 

ADVERTISEMENT

Cisco WAN :: Limiting Bandwidth On Router 1800 Series

Jul 29, 2010

I will have this one router. Its f0/0 will be for the Internet connection with bandwidth of 30Mbps. Its f0/1 will be connected to a switch for internal networks. This link will be separated to 3 VLANs for 3 internal networks. I'm wondering if there is a way to gurantee 10Mbps for each VLAN but allow use up to 30Mbps when another two VLANs are not using any Internet bandwidth? I only worry about download bandwidth from internet.The 3 internal networks will all have public IPs and they belong to their own subnets. There won't be NAT/PAT.

View 18 Replies View Related

Cisco WAN :: 1800 Series Router - QoS On FastEthernet Subinterface

Jun 28, 2011

We have 2.5 Mbps connection from an ISP at our branch routers (1800 series)with single physical link terminated on FE0 but have two subinterfaces with separate subnets.
 
I have applied the following policy-map outbount under physical Interface FastEthernet 0. Show poliocymap output is as follows
 
Policy Map QoS-OUT
   Class Email
     priority 512 (kbps)
   Class SQL
     priority 512 (kbps)
   Class File-Copy
    police cir 1024000 bc 32000
      conform-action transmit
      exceed-action drop
   Class CCTV
    police cir 384000 bc 12000
      conform-action transmit
      exceed-action drop

But it seems that sometimes( not all the time ) the CCTV traffic seems to exceed the 384k and chokes the entire link(2.5 mbps).

View 4 Replies View Related

Cisco Switching/Routing :: To Edit Configuration In 1800 Router

Jan 11, 2012

I am new user of cisco router i can access the hardware and login in the account but the problem is if i use the command "enable" asking for a password, old I.T. personnel who setup this router already resign.

View 2 Replies View Related

Cisco WAN :: Configuring QOS Between 2800 And 1800 Series Routers

Feb 20, 2012

We have an MPLS network to a half dozen remote sites.  At our main location we have a 2800 series router.  In the routers config are the following lines for QOS.  When I go to the routers on the other end of the MPLS, none of them are configured with these same policies.  Would these not be in the running config of the 1800 series routers, or is this not setup correct and this should be removed?

View 13 Replies View Related

Cisco VPN :: 1800 - Static Crypto Configuration

Sep 3, 2012

I ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , the traffic dynamic crypto can not be used since traffic may be initiated from Dc on other link which may get dropped incase not encrypted.

View 5 Replies View Related

Cisco WAN :: 800 Series Router Basic Configuration

Sep 4, 2012

I have just bought my first non-domestic router, a CISCO 887VA-K9 which needs basic configuration to get it working.  I have a copy of the configuration guide (334 pages) and CP Express user's guide (94 pages) and have spent an hour reading but either they are missing something or my brain is too small to figure out step 1.  How to get started.  Perhaps from where to download a CP Express installation kit for Windows.
 
Is the only way via a terminal emulator connected via a serial port ?  Is there a graphical interface I can use ?  Are there any basic tutorials for beginners ?  This is probably the only non-domestic routrer I shall work on so I don't want to invest in a full training course.  I just need enough to plug in the ISP credentials and set up DHCP.

View 27 Replies View Related

Cisco Switching/Routing :: 800 Series Router Configuration

Jun 13, 2012

about to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.

View 5 Replies View Related

Cisco WAN :: Dynamic Configuration Of 3900 Series Router

Dec 12, 2010

Am trying to do a dynamic configuration of a 3900 series router (3925 to be precise).For the software and licenses, under the IOS technology Package Licenses, what's the significant of SL-39-DATA-K9 and SL-39-SECNPE-K9? Are they really necessary for the router?

View 3 Replies View Related

Cisco Switching/Routing :: Copy Startup Configuration From 877W To Another 870 Series Router?

Jan 4, 2012

I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?

View 4 Replies View Related

Cisco WAN :: Can't Use Ehwic-3g-hspa-u Card In 2800 Series And 1841 Series Router

Jun 2, 2012

why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios  advance ent. 15.1(4)M4?

View 3 Replies View Related

Cisco WAN :: 1700 Series Router To 2811 Series Router / Going From T1 To Ethernet?

Jan 17, 2011

I  have not done much with business routers, but we have a 1700 series  with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and  will be moving to ehternet. We are going to be moving to a 20MB line,  and i just wanted to make sure I have the right connections before  installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We  would also like to copy over the configuration from 1700 series router  to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?

View 2 Replies View Related

Cisco WAN :: 1800 Router SNR At 3db?

Sep 19, 2012

Cisco 1800 router SNR at 3db

View 3 Replies View Related

Cisco Switching/Routing :: CLI Configuration Of 800 Series Routers

May 1, 2013

I've goggled and searched here, and I can't seem to find what I'm looking for.  I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.

View 2 Replies View Related

Configure Cisco Router 1800 To IP VPN?

Jan 23, 2011

My boss want me to configure a cisco router 1800 series to an IP VPN, but I don't know how to configure a router with an IP VPN...

View 2 Replies View Related

Cisco WAN :: New IP For 1800 Router Running VPN?

Aug 28, 2012

I have an existing 1800 router that is using NAT and VPN to HQ. I now have a new ISP provider and so now i need to chane the Fastethernet1 IP address. I know how to do that but what else do I need to change to make everything continue to work?

View 10 Replies View Related

Cisco WAN :: How To Use 1800 Router As VPN Firewall

Jan 25, 2011

How can I use a 1800 router as a firewall. I want also the router be able to make VPN.

View 1 Replies View Related

Cisco Switching/Routing :: How To Copy Configuration From 2900 Series To Another One

Oct 11, 2012

I know we can use copy & Paste, my questions are:

1.       Before that, do I need to wipe out the existing confi on the brand new switch?

2.       About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?

View 3 Replies View Related

Cisco WAN :: Routing With 3 Public IP Net On 1800 Router

Nov 28, 2011

I don't know much about routers, but lately I've been playing around with router configuration and getting better but I am kind of stuck now.
 
The scenario is this.
 
I have 3 ip net from the ISP:
178.249.51.0/255.255.255.248 Gateway 178.249.51.1
178.249.51.8/255.255.255.248 Gateway 178.249.51.9
178.249.51.16/255.255.255.248 Gateway 178.249.51.17

[Code]....

I am also wondering - when we get more public IP net from the ISP, is this the correct way to do it?

View 5 Replies View Related

Cisco WAN :: 1800 Router PPPOE Authentication?

Sep 3, 2012

What commands do I need to enter to correctly authenticate with my DSL PPPOE provider? I need to have the ID and Password entered into the router.

View 19 Replies View Related

Cisco VPN :: 1800 Not Encrypting Traffic On One Router

Oct 18, 2011

I'm troubleshooting an issue with a new site-to-site vpn setup between 1800 series routers.  The tunnel is up but not encrypting traffic on one router, when  IP CEF is disabled traffic is encrypted and decrypted!

View 1 Replies View Related

Cisco Infrastructure :: NATing With Router 1800

Oct 12, 2011

I have the following network connected and configured to a single Cisco 1800 router.

VLAN 2 (10.1.20.0/24)
|
int vlan2, ip address 10.1.20.1
|
 Cisco 1800 ----- int fa0, public ip address ---- Internet
|
int vlan3, ip address 10.1.30.1
|
VLAN 3 (10.1.30.0/24)
 
VLAN 2 is server vlan with a webserver.
VLAN 3 is clients.
 
NAT configuration:
VLAN 2 and VLAN 3 is using NAT to access the internet, and both is configured as inside interfaces.fa0 is configured as outside interface. Now I don't know if this is about NAT, but I've tried several things without luck.
 
Problem:
A client in VLAN 3 tries to access a domain on the webserver in VLAN 2.It starts by sending a DNS query to a DNS server located at the ISP, and gets the ip address for the domain, which is of course a public ip address. Then nothing happens because the client tries to access the domain on the webserver using the public ip address, and the webserver have a local ip address 10.1.20.20 which is on the local LAN (VLAN 2).
 
I've tried NAT because I have to change the destination ip address, but I can't seem to get it right.

View 3 Replies View Related

Cisco WAN :: Why Does Automatic DHCP Configuration No Longer Work On 1900 Series

Jan 8, 2013

We have been using a dhcp and  tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out".  Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming.  Doing configurations without automation for that many is moving in the wrong direction.

View 1 Replies View Related

Cisco WAN :: When Creating Failover Setup Cause 1800 Router To Hob Away

Mar 20, 2013

I have been given a task, where I need to create a failover setup from a 1800 Cisco router to a LAN network 2 hobs away (see topology).The reason I have been given this task is because the wireless links are not so realiably, but necessary.I'm thinking of doing this failover task with IP SLA on the routers fiber 1 and fiber 2 link, so when/if one off the links goes down, it instantly chooses the other link.I have also been thinking about implementing STP instead, and replace the router with a switch, but i'm not sure exactly how to implement it. Unfortunately I'm not able to test anything, as we are still waiting for the fiber lines, but I want to be prepared as much as possible.

View 5 Replies View Related

Cisco WAN :: Failover On Router 1800 Having DSL And Leased Line

Feb 4, 2013

Leased line is between dammam      to dubai and the dammam office is getting internet from dubai.The ip address of Dammam      office is class A (Public IP) x.x.x.x and for dubai it is y.y.y.y which we are      using as proxy for accessing internet.I purchase the local DSL      direct line connection through cable from Local Provider and this ip address range is      192.168.1.0 - 192.168.1.254.Is it possible to use the DSL      line as failover, so if one line goes down the user should remove proxy      and can use local internet.The router which is using is      cisco 1800. 

I believe that failover is possible, 100%, but would like to know how I can do it and requesting for sharing more inputs about failover in this case.

View 2 Replies View Related

Cisco WAN :: Changing Router From 1800 To 2901 With Same Config

Dec 22, 2010

I have configured PBR on my 1800 series router, it is working perfect. Now I am changing my router from 1800 to 2901 router with the same config, so the PBR stop working and I am not getting hits in the second WAN interface. [code]

View 2 Replies View Related

Cisco WAN :: 1800 Updating System Image Without Rebooting Router

Feb 26, 2013

I recently formatted the flash drive of an 1800 router and replaced it with an updated image. However, the new features within the new image aren't reflected in the router. I believe that this is because a reboot would be required for the updates in the new image to be reflected in the router i.e. the image needs to be added to the system. How to get the image to the system without a reboot and if by doing so I would get all the new features from the image.For example, the show version below shows the old image in the system as [code]

View 2 Replies View Related

Cisco Switching/Routing :: Can't See Any Debug Message On 1800 Router

Jul 19, 2012

I have strange problem with 1800 router , I can't see any debug messaging , the ping from PC to this router is Ok , but no icmp debug appears , even I enable "debug ip icmp "  the version of router is : C181X Software (C181X-ADVENTERPRISEK9-M), Version 12.4(6)T6

View 2 Replies View Related

Cisco WAN :: Limited Inbound Traffic To 3 Mbps On Router's Interface 1800

Jun 22, 2012

I have two 1800 routers running VRRP. Also I have two sub interface configured on both router and both router connected to swith through thunk link. My goal is to limit inbound traffic to 3Mbps for both VLANs on router's inside interface which is connected to switch.

View 1 Replies View Related

Cisco WAN :: 1800 Router Does IP NAT Translation / Slow Internet Access For Users

Oct 4, 2012

We have an ethernet port on Cisco router 1800 connected to the ADSL modem. The router does ip nat translation, but users complained it is slow when they access to internet. [code]

View 1 Replies View Related

Cisco WAN :: Poor Performance And Internet Router 1800 Cable Virgin Media

Dec 17, 2011

Im getting really poor performance on my 1841, my intial thoughts was a duplex mismatch  however although im getting a few CRC errors (root cause unknown at this point) not enough to suggest that the this is the issue.

Heres the config:

Building configuration.Current configuration : 5274 bytesLast configuration change at 20:31:01 PCTime Sun Dec 18 2011 by admin_xversion 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname   xxxxxx!boot-start-markerboot-end-marker!!security authentication failure rate 10 log

View 7 Replies View Related

Cisco Switches :: How To Erase All Configuration In ESW 500 Series Switches

Aug 21, 2011

How to erase or remove  configuration file from ESW 500 Series Switches?

View 2 Replies View Related

Cisco VPN :: Make Site-to-site VPN Between 1800 Router And ASA 5510

Nov 29, 2011

I was traying to make a site to site VPN between a cisco 1800 router and cisco asa 5510. But it was impossible to get it. [code]

View 1 Replies View Related

Cisco Wireless :: Controller 4400 Series Work With Aironet 3600 Series

Mar 6, 2012

Can Controller 4400 series work with Aironet 3600 series?

View 5 Replies View Related

Cisco Wireless :: 1140 AP Series Vs 1260 AP Series Technical Differences

Jul 24, 2012

What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?

View 10 Replies View Related

Cisco Routers :: How Does Quality And Longevity Of SRP500 Series Compare To RV Series

May 27, 2012

My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price.  How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?

View 1 Replies View Related

Cisco :: Does WLC 2500 Series Supports 1262 Series Access Point

Jun 14, 2011

Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9  Access Point? How can I check this?

View 1 Replies View Related

Cisco WAN :: 1800 - VRF Lite Scalability

Feb 14, 2011

Imagine organization has about 300 partners. Currently data center has 100 Cisco 1800 routers to accept P2P connections for each partner.
 
Now organization proposal is:
 
- Use MPLS and use an extranet network. Advertise a certain unique route to each partner..
- Grant unique VPN ID for each partner and VRF Lite at the data center. Then bring each partner with separate tagged VLAN to the data center via MPLS.
 
Can VRF Lite scale to more than 300+ partners OK?

View 1 Replies View Related

Cisco WAN :: 3 NAT Addresses On 1800 Firewall

Oct 15, 2012

I have a client that has 6 public  IP addresses.  He needs to use 3 of them.  One for workstations which is  currently working fine.  It is using the default gateway IP.  One for a  email/web server which has a statis NAT and is also working fine.  But  we need an additional NAT but it is for 3 servers that all need to go  out as the smae public IP.  I am not sure and been unsuccessful getting  those to go out as the same IP.  I either cannot get them to exit the  same IP or it breaks the workstation NAT.
 
Workstations would be 10.0.0.100 - 200 going oput the FE1 interface or I think x.x.94.122
Email would be 10.0.0.5 going out the statis NAT of x.x.94.123
I then need 10.0.0.2 - 4 to go out x.x.94.124
 
I removed some ACLs and IP info for security. Attached is the current config.
 
interface FastEthernet0
description $ETH-WAN$$FW_OUTSIDE$
ip address x.x.4.240 255.255.255.0

[Code]....

View 1 Replies View Related

ADVERTISEMENT