I have few queries abou the Cisco 880G series router.
1) Suppose if we have a 3G service enabled SIM card then can we insert the same on the Cisco 880G router and browse internet from the LAN of 880G?
2) I think the HSPA+ standard supports 84 Mbps downlink speed..... so is it supported on 880 G router?
3) Can we configure Cisco 880G as a CME?
we are intending to purchase some 887G router for one of our client, but we not sure if it support "performance routing" or not. coz we don't see it on cisco's datasheet, and "cisco feature navigator" don't have that information.
View 4 Replies View RelatedAs my main router i have the CISCO 880G with the ip 192.168.1.1 at the ethernet interface 0 and my WAN connection at my ethernet interface 4.If the other end of my cable from ethernet intrface 0 i put it to another device which has the IP 192.168.1.2 to its WAN port and define the DMZ port of that other device as transparent with rules to pass all but to register and filter some things.When i have them like this i cannot reah to neither CISCO neither other device with ip 192.168.1.2.
View 1 Replies View Relatedhow many users supports the 2600 series ap air voice, video, and data average any document or link
View 3 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedMY voice conversation on magic jack breaks up when I download a movie to my direct TV. I have a Belkin F9K1103V1, N750Db. I'm not using WiFi, Im wired to ports on back of Belkin.
View 3 Replies View RelatedI have a cisco2811 router and i want to convert or make it to be a voice enabled router? it has a current image/ios of (C2800nm-adventerprisek9-m), version 12.4(5a).
View 4 Replies View RelatedWhat's the best router / handset to get to practice for CCNA Voice?
View 2 Replies View RelatedSince I am new to VOIP and am getting confused with the responses online on how to connect to a commercial phone system I thought I would ask here. I have a small voice router (1751) running CME with 2 Cisco 7940 phones. I would like to hook it up to a commercial line, but not sure how to. What specific card will I need for my voice router to connect it to the outside world (FXO right)? I see where they talk about hooking it up directly to the LAN line, another using a commercial phone system, and then the others using a PBX,ect... So confused to say the least. I assume I need an FXO port to connect to the POTS, but not sure if there is anything else I’m missing in the setup...
View 4 Replies View RelatedWhen I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies View RelatedWe're having some numbers ported over to us and we'd like to verify that we are in fact receiving all of the numbers at our SIP gateway. Since we have been getting more and more activity on this router, I'm becoming more concerned about using certain debug's for fear that the router maxes out CPU and drops.
What the best debug command would give me this information with minimal impact on CPU? In the past I've used 'debug ccapi inout' and a couple of others similar to that. With so much activity though sometimes it bombs the router. Also I am logging to the console directly, maybe there is a better method with less CPU impact. I just don't want to have to go back and forth to look for stuff 50 times either if I write out to a file or something, it could work though I suppose.
We have a 2800 router which is configured as a Voice Gateway. For some reason, yesterday we started getting DFM notifications like the one below. We seems to get an active messages every few 10mins or so, then a few minutes later the message will clear before becoming active again...
EVENT ID = 0009NK2
ALERT ID = 0000QTM
TIME = Tue 21-Jun-2011 16:06:50 BST
STATUS = Active
SEVERITY = Critical
MANAGED OBJECT = XXXXVG1
MANAGED OBJECT TYPE = Routers.
I need to configure two voice-enabled cisco routers, each one has an analog FAX machine. The routers are connected with a serial connection. In the end, the faxes should be able to fax to each other.The fax uses RJ-11 and I've established that I will be configuring FSX ports. (These ports are used for analog devices such as telephones, modems, and fax machines). I am unable to find a single site that gives information about specifically configuring fax machines.
View 3 Replies View RelatedI recently moved to a cable ISP and unfortunately had to also change routers in order to take advantage of the VoIP feature (analog phone) they provided me with.Now, the new router, the WRP400, is very limited feature-wise compared to the custom flashed WRT54GL I used to use with my DSL provider.Now the WRT54GL does not have any FXS ports, so I obviously can't just plug my cable modem to the WRT54GL. Therefore, I was hoping to achieve a setup similar to this one:Cable modem => VoIP Router w/ voice only (WRP400) => "Main" router (WRT54GL w/ Tomato)Is there a way to bridge the WRP400 successfully with the WRT54GL keeping only the voice feature enabled on the VoIP router while the WRT54GL takes care of the rest? (Wireless, WAN, port forwarding, etc)
View 2 Replies View RelatedWe have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
I'm trying to configure QoS on my 877 router to give priority to voice packets. However, when I do a show policy-map for WAN interface, all the classes show 0 bps. When I do a show int for the WAN interface, I get the correct bandwidth util.
This 877 is meant for a home network. I'm running a Cisco 7970 phone using phone-proxy back to my HQ. I'm also shaping the traffic.
Here is my config
Class Map match-any EF (id 1)
Match ip precedence 5
Class Map match-any class-default (id 0)
Match any
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWe want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
I am configuring DHCP pool for voice vlan on cisco 2921 router.
Here is the setup.
2921 router -> 3750 -> 2960 PoE -> 7942 IP Phone
Router Config
ip dhcp excluded-address 10.146.54.1 10.146.89.50
!
ip dhcp pool VoiceVlan
network 10.146.54.0 255.255.255.0
subnet prefix-length 24
dns-server 10.144.68.32 10.144.68.33
option 150 ip 10.146.68.36
default-router 10.146.54.1
netbios-name-server 10.144.68.32 10.144.68.33
netbios-node-type h-node
[code]....
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies View RelatedCan i do sub-interface in cisco 891 or 881 series router ? 1900 and 2900 series router support sub-interface ?
View 1 Replies View Relatedi am proposing cisco 892 series router for multi VRF Configurations-MPLS. Is there any challenge you foresee in this architecture.
View 4 Replies View RelatedI have a router 819 with 3G built-in. Are there any manual for how to setup the interface celluar 0 for this router out there? I have Verizon as my 3G provider.
View 4 Replies View RelatedI am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies View RelatedI just recently bought a ASA5505 with a licence that can have 2 WebVPN Peers, I would like to have a phone to my CCME server as one of the options within that web-vpn thingy.
View 3 Replies View Related i need any one exact IOS from below list .can some provide me the link.
15.1(0.20)T
15.0(1)M1.4
15.1(24.6.26)PIL13
15.1(0.2.12)PIB13
15.1(1)XB1
15.1(0.0.10)PIL14
15.1(1.7.1)PIA13
15.1(1.7.1)PIA14
15.1(0.0.3)PIL15