Configure Fax Machine On Voice-enabled Router?
Jan 17, 2011
I need to configure two voice-enabled cisco routers, each one has an analog FAX machine. The routers are connected with a serial connection. In the end, the faxes should be able to fax to each other.The fax uses RJ-11 and I've established that I will be configuring FSX ports. (These ports are used for analog devices such as telephones, modems, and fax machines). I am unable to find a single site that gives information about specifically configuring fax machines.
View 3 Replies
ADVERTISEMENT
May 12, 2011
I have a cisco2811 router and i want to convert or make it to be a voice enabled router? it has a current image/ios of (C2800nm-adventerprisek9-m), version 12.4(5a).
View 4 Replies
View Related
Dec 21, 2012
When I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies
View Related
Dec 6, 2010
I'm trying to configure QoS on my 877 router to give priority to voice packets. However, when I do a show policy-map for WAN interface, all the classes show 0 bps. When I do a show int for the WAN interface, I get the correct bandwidth util.
This 877 is meant for a home network. I'm running a Cisco 7970 phone using phone-proxy back to my HQ. I'm also shaping the traffic.
Here is my config
Class Map match-any EF (id 1)
Match ip precedence 5
Class Map match-any class-default (id 0)
Match any
View 5 Replies
View Related
May 24, 2012
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
View 4 Replies
View Related
Aug 20, 2012
I have the following setup: Private network <-> SW <-> CISCO VPN <-> ISP MODEM
I have configured VPN part and is working correctly. I have a computer in the private network at static address 192.168.1.100 and an application is running on it on 8100 tcp port for clients.
Now I need to connect from the Internet to the application on 192.168.1.100 on port 8100.
How to configure CISCO router to forward traffic coming in tcp port 8100 to machine 192.168.1.100?? ISP Modem is going to handover all the traffic to CISCO device.
View 8 Replies
View Related
Nov 19, 2012
Is there a way to configure a disclaimer that will pop up on the client machine that they will need to accept to be allowed access to the wireless network?
View 3 Replies
View Related
May 12, 2011
We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies
View Related
Jun 16, 2011
I want to configure QoS for voice traffic over a site-to-site VPN tunnel. I have a Cisco 851 router on the branch end and a Cisco 1800 router at the HQ. The setup is an Avaya Gateway located at the HQ and the idea is that the phones at the branch office are connected over the VPN tunnel to the gateway at the HQ.
I have a 1MB internet link at the HQ from a service provider and 256kbps internet link (from a different service provider) at the branch office. The branch office has just 3 users.
View 12 Replies
View Related
Aug 2, 2011
I have a strange error on my home network that I cannot find a solution to.I have an Huawei SmartAX MT882 from TalkTalk acting as a modem connected to a D-Link DSL-G624T acting as a router/switch. Connected to the D-Link I have a Windows 7 Pro machine (64-bit, SP1) and an XP (home i think) machine (sp 2 i think).The SmartAX modem is set up to perform DHCP and DNS relaying and the D-Link has DHCP turned off and DNS relay turned off.The Win7 machine can access the network, get an IP address and access the internet without problems, regardless as to the status of the XP machine.The XP machine can access the network, get an IP address and access the internet with no problems ONLY of the win7 is powered up. When the win7 machine is off, the XP machine seems to drop about 25% of the ping packets between it and the D-Link router and has no internet access (because of this i assume). [code]
View 8 Replies
View Related
Jul 20, 2011
New Win-7 machine set up. I used the printer set-up wizard to install a networked printer in the new machine with absolutely no problem. Proved it would print from that machine.Now, I get a call informing me that her old XP machine, which had been printing to the network printer with no problems, will no longer print.Documents go into the print queue, but they don't get printed.No error messages show up.I did some messing around via remote access, and finally removed the printer with the intention of reinstalling it.Scanning for network printers turned up several redundant instances of the same printer with different names. Some are identified as "invalid" some a "access denied". Bottom line. I can't get any of the selections to install.On the Win-7 machine I did find a window that indicated that the printer is designated as being shared, but I didn't explicitly set it for sharing when I installed it. Also, I somehow got to a window that told me that for printers that were to be shared with other versions of windows I could optionally install drivers to support such machines. Didn't have the driver disk handy and took the window down. Now I can't even find it again.I need sorting this all out.Part of the problem is that out there in "network land" there are redundant remnants of previous installations that are being remembered inappropriately.
View 11 Replies
View Related
Apr 29, 2012
I have a network problem. My windows 7 machine is not detecting win xp machine whereas win xp machine is detecting win 7 machine. They are in the same workgroup named Home. And the networking system is set to work. I have left the homegroup I was previously in. I enabled file sharing for devices that use 40 bit and 50 bit encryption. On XP I have enabled NetBios over TCP/IP. File sharing is enabled on both computers. I think it's something obvious as both instalations on different computers are really fresh and both windows haven't been tampered with.
View 12 Replies
View Related
Aug 15, 2012
MY voice conversation on magic jack breaks up when I download a movie to my direct TV. I have a Belkin F9K1103V1, N750Db. I'm not using WiFi, Im wired to ports on back of Belkin.
View 3 Replies
View Related
May 20, 2012
I recently moved to a cable ISP and unfortunately had to also change routers in order to take advantage of the VoIP feature (analog phone) they provided me with.Now, the new router, the WRP400, is very limited feature-wise compared to the custom flashed WRT54GL I used to use with my DSL provider.Now the WRT54GL does not have any FXS ports, so I obviously can't just plug my cable modem to the WRT54GL. Therefore, I was hoping to achieve a setup similar to this one:Cable modem => VoIP Router w/ voice only (WRP400) => "Main" router (WRT54GL w/ Tomato)Is there a way to bridge the WRP400 successfully with the WRT54GL keeping only the voice feature enabled on the VoIP router while the WRT54GL takes care of the rest? (Wireless, WAN, port forwarding, etc)
View 2 Replies
View Related
Mar 15, 2011
I have few queries abou the Cisco 880G series router.
1) Suppose if we have a 3G service enabled SIM card then can we insert the same on the Cisco 880G router and browse internet from the LAN of 880G?
2) I think the HSPA+ standard supports 84 Mbps downlink speed..... so is it supported on 880 G router?
3) Can we configure Cisco 880G as a CME?
View 2 Replies
View Related
May 16, 2011
What's the best router / handset to get to practice for CCNA Voice?
View 2 Replies
View Related
Sep 6, 2011
Since I am new to VOIP and am getting confused with the responses online on how to connect to a commercial phone system I thought I would ask here. I have a small voice router (1751) running CME with 2 Cisco 7940 phones. I would like to hook it up to a commercial line, but not sure how to. What specific card will I need for my voice router to connect it to the outside world (FXO right)? I see where they talk about hooking it up directly to the LAN line, another using a commercial phone system, and then the others using a PBX,ect... So confused to say the least. I assume I need an FXO port to connect to the POTS, but not sure if there is anything else I’m missing in the setup...
View 4 Replies
View Related
Oct 24, 2011
We're having some numbers ported over to us and we'd like to verify that we are in fact receiving all of the numbers at our SIP gateway. Since we have been getting more and more activity on this router, I'm becoming more concerned about using certain debug's for fear that the router maxes out CPU and drops.
What the best debug command would give me this information with minimal impact on CPU? In the past I've used 'debug ccapi inout' and a couple of others similar to that. With so much activity though sometimes it bombs the router. Also I am logging to the console directly, maybe there is a better method with less CPU impact. I just don't want to have to go back and forth to look for stuff 50 times either if I write out to a file or something, it could work though I suppose.
View 1 Replies
View Related
Jun 20, 2011
We have a 2800 router which is configured as a Voice Gateway. For some reason, yesterday we started getting DFM notifications like the one below. We seems to get an active messages every few 10mins or so, then a few minutes later the message will clear before becoming active again...
EVENT ID = 0009NK2
ALERT ID = 0000QTM
TIME = Tue 21-Jun-2011 16:06:50 BST
STATUS = Active
SEVERITY = Critical
MANAGED OBJECT = XXXXVG1
MANAGED OBJECT TYPE = Routers.
View 1 Replies
View Related
Apr 19, 2009
BEFSR81 v3.0.I selecting Enabled UPnP and now I cannot access the router. When I enter the default admin for the password in the Authentication Required screen. I get the following screen: 401 Authorization RequiredThis server could not verify that you are authorized to access. Either you supplied the wrong credentials(e.g., bad password), or your browser doesn't understand how to supply the credentials required.I didn't enter anything new into the username or password fields.
View 5 Replies
View Related
Mar 6, 2013
I am using my neighbor's WiFi connection in my WiFi enabled motherboard PC with good signal strength. Now i want to connect a router to my PC so that i can easily use WiFi for my mobiles.
View 4 Replies
View Related
Apr 22, 2011
We have some point-to-point sites linked with our HO with 10-30mbps speed. We have provided DID telephone lines to these sites as well.
We want to limit the bandwidth with 1mb bandwidth only and also make sure that the voice traffic (DID telephone lines) gets the priority over all other traffic even if they are utilitizing the 1mb link completely. We have some Cisco 1841 routers that we are planning to configure on the main uplink on each of these sites. how to give the priority to the voice traffic yet limiting the bandwidth to 1mb.
View 8 Replies
View Related
Sep 20, 2011
I have just bought a Wansview NC541W IP Camera to monitor my home while I am at work (my home was burgled recently) and I have no idea how to connect it to my broadband router wirelessly. I went onto the network settings of the Camera and set up the wireless setting to connect to my router network (typed in the SSID and wireless pass key etc) but nothings happening?!? I can connect the two devices with an Ethernet cable and have the camera working perfectly, but can't do it wirelessly!
View 1 Replies
View Related
Dec 3, 2012
We have installed a VWIC3-2MFT card on a Cisco 3945 voice gateway but the router doesnt detect the card. out put is as below;
Router Version
============
System image file is "flash0:c3900-universalk9-mz.SPA.150-1.M.bin"
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
[Code]....
View 8 Replies
View Related
Dec 11, 2012
I was trying to port fwd my RDP and then I ended up getting side tracted and changed my routers password [URL] it would cause my router to stop working. I know my adapter is fine, because I can connect to the internet via wired connection. My wifi DHCP is not enabled however and I have no clue on how to enable it.
Here is the settings from ipconfig/all
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
C:UsersAlex>ipconfig/all
[code]...
View 2 Replies
View Related
Aug 25, 2012
Well i am currently using a BSNL DNA A211-1 wifi modem-cum-router with a wireline inbetween my PC (win7 ultm) & the router, so as to connect to the internet. i use the wifi feature of my router to connect my samsung gts5570 wifi enabled phone as well as a few other wifi enabled devices, to use internet on them. now i was thinking whether i can connect my desktop pc to my mobile phone using this wifi router somehow? how can that be done since there is already 2 different network that exist between my pc & router thru wireline & my mobile & the router thru wifi, all i need is a way to sync these to networks into one, so that my pc & my mobile use internet & at the same time they connect to each other as well.
View 3 Replies
View Related
May 27, 2012
Ever since I bought the E4200 months ago I had no wireless network between my laptops. pc's devices. I discovered now that I do have network (everything cool) when I disable NAT. That is all nice, but I don't have internet then.
View 8 Replies
View Related
Nov 6, 2012
i have a wireless laptop that i can connect to one network but when i bring it to another network that i can connect many computers to at random, it will not connect. it says Network no longer available. the router sits about 3 feet away from it. if i hook up a wire it works just fine. even cell phones connect just fine to the network.
View 4 Replies
View Related
May 21, 2012
We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
View 15 Replies
View Related
Mar 30, 2011
My router is running the stock 1.21 firmware and it has been fine for almost a year before the wireless suddenly stopped working. I reset the router and restored my previous configuration. After the reboot, the SSID is visible and I can connect to it but there is no internet connection. Also the router becomes unresponsive, i.e. timeout trying to access the router configuration page. After trying out different settings it seems that enabling WPA2+AES is the cause.In the mean time, I am running an open wireless network and everything seems fine. Is the hardware faulty? I am reluctant to update the firmware because of a negative experience with another router (same model).
View 2 Replies
View Related
Sep 8, 2012
Due to an issue with having to support an ALG enabled phone and a non-ALG enabled phone, I have a requirement that both NAT and RIP be enabled simultaneously, is there a Linksys product that can support this requirement? Or, more preferably a firware upgrade for the E4200 that will support this?
View 3 Replies
View Related
Jul 18, 2012
Which is the best way of creating GRE Tunnels on a GLBP enabled router? I actually have two 3845 with GLBP configured as our gateway routers, and need to create gre tunnels to branches.The plan is to use the GLBP virtual IP as the Tunnel Source address and the branch WAN interface as the tunnel Destination address, how do i handle the Tunnel IP address? Do i create the same Tunnel on both gateway routers and have a glbp virtual IP address for the Tunnel Interface as well?
View 4 Replies
View Related
Feb 5, 2013
We want to use a Cisco 861 Ethernet router to link our LAN's data and voice segments together (each on separate switches). Our switches are not Layer3 so routing over them is not an option. We only use the default VLAN1 on both switches.There is a data segment 192.168.1.0/24 and a voice segment 192.168.150.0/24, each with it's own internet/WAN access (internet for the data lan and SIP provider for the voice lan).
Diagram:
internet-~--router_192.168.1.1------192.168.1.0/24_data_lan--------192.168.1.254_cisco861_192.168.150.254-----192.168.150.0/24_voice------192.168.150.1_router--~-sip_provider
This is want i want to achieve:
- Link the data and voice switches using the 861
- I want to make the Cisco 861 the default gw on both segments, but they should only route traffic destined for the other segment to each other and route all other traffic to their segment's designated internet connection. I don't want the Cisco to do any NATting and there's no need for firewalling either.
View 3 Replies
View Related
