Cisco :: 2800 Router - Voice Gateway DFM Notifications
Jun 20, 2011
We have a 2800 router which is configured as a Voice Gateway. For some reason, yesterday we started getting DFM notifications like the one below. We seems to get an active messages every few 10mins or so, then a few minutes later the message will clear before becoming active again...
EVENT ID = 0009NK2
ALERT ID = 0000QTM
TIME = Tue 21-Jun-2011 16:06:50 BST
STATUS = Active
SEVERITY = Critical
MANAGED OBJECT = XXXXVG1
MANAGED OBJECT TYPE = Routers.
View 1 Replies
ADVERTISEMENT
Jan 10, 2012
I have a customer who has a Cisco 2821 router with software 2821/HSEC/K9 and they wish to upgrade to C2821-VSEC-SRST/K9.From my understanding they want to use the same router but install an IOS with the capabilites it has at the moment but with voice. [code]How do I go about pricing this up and what upgrade sku's will do this?I am not to worried about the memory.Is it just a simple ios upgrade as the srst licenses are on a trust basis?
View 2 Replies
View Related
May 21, 2012
We have two MPLS circuits managed by two different suppliers, one carries VOICE the other DATAWe are to decommision the VOICE MPLS and have increased the bandwith of the DATA MPLS to carry VoIP traffic too.
At both of our sites A & B ,devices connected to the LAN have a default gateway of the VOICE providers Cisco 2600 router , which then goes into the LAN switching. (see diagram)So what I am trying to achieve is toto simply replace these 2600 routers from the VOICE MPLS provider with our own so we dont have to change the default gateways at both sites.
Testing
Our Cisco 2600 routes are plugged into each LAN switching environment with two subinterfaces configured, one for voip and the other for dataThe problem is from the router and respective subinterfaces we can get to the other sites destination without any issue, but if for example a user is at site A with Ip address 10.16.11.12/16 they cant ping the VOIP subnet at site B 10.3.11.0/24. But If a ping is issue from the Site A test router then the 10.3.11.0/24 subnet is reachable but only on the 10.3.12.0/24 configured subinterface.So i guess what Im saying is 10.16.0.0/16 from the LAN needs to be able to get to 10.3.11.0/24Note at site A 10.16.0.0/16 & 10.3.12.0/24 can communicate no problem and at site B 10.207.0.0/16 & 10.3.11.0/24 can communicate no problem.We are using IP routing, should we be using route-maps?
View 15 Replies
View Related
Jun 8, 2012
i need any one exact IOS from below list .can some provide me the link.
15.1(0.20)T
15.0(1)M1.4
15.1(24.6.26)PIL13
15.1(0.2.12)PIB13
15.1(1)XB1
15.1(0.0.10)PIL14
15.1(1.7.1)PIA13
15.1(1.7.1)PIA14
15.1(0.0.3)PIL15
View 1 Replies
View Related
Jul 8, 2011
Though i am working on cisco call manager.I know some stuffs about Call Manager. Diff between CallManager, GateKeeper and Voice Gateway.
View 7 Replies
View Related
Mar 14, 2012
we are using single cisco 3845 gateway as Ingress as well as vxml gateway . Can you provide any documentation regarding the call volume capacity this gateway can handle. We have deployed this gateway in a UCCE parent- child model.
View 2 Replies
View Related
Jun 28, 2012
Is there a way to get notifications (emails) when the external ip changes and the rotuer updates dyndns?i need to get an email about this change of ip. The only constraint is it has to work without a computer attached to the router as it would have to be powered on 24/7 So ip change notifiers like trueip or ipcheck won't work as they are programs that run in a computer.
View 9 Replies
View Related
Apr 27, 2011
Am running LMS 4.0 on windows 2003 server, i would like to disable or remove notifications with the EventName 'ExceededMaximumUptime' and 'BackupActivated' on the device fault summary view. How do i achieve this? This will be useful in only monitoring fewer notifications.
View 3 Replies
View Related
Jan 24, 2012
I recently swapped out an RV082 with a newer model (still RV082 but black and a different interface). I configured the Gateway to Gateway VPN exactly as it was before but none of the three other RV082's will connect. I have tried deleting the connections several times to no avail. I have aggressive mode disabled and have tried with the firewall on and off. Below are the settings (IP's have been X'd out) and the log.
Settings:
IP OnlyIP Address : X0X.X0X.20.31Local Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : Remote Group Setup
Remote Security Gateway Type : IP OnlyIP AddressIP by DNS Resolved : Remote Security Group Type : IPSubnetIP RangeIP Address : Subnet Mask : AES-192AES-256AES-128 AES-192AES-256 AES-128 IPSec Setup3DES Keying Mode : ManualIKE with Preshared keyPhase 1 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 1 Encryption : DES Phase 1 Authentication : MD5SHA1Phase 1 SA Life Time : secondsPerfect Forward Secrecy : Phase 2 DH Group : Group 1 - 768 bitGroup 2 - 1024 bitGroup 5 - 1536 bitPhase 2 Encryption : NULLDES3DES Phase 2 Authentication : NULLMD5SHA1Phase 2 SA Life Time : secondsPreshared Key : Minimum Preshared Key Complexity : EnableLOG:
[code].....
View 1 Replies
View Related
Jul 11, 2012
My two RV042 , one at home and the other one at my working site, constantly lost VPN connection after successfully connected.Both Firmware are identical. [code]
View 1 Replies
View Related
Feb 8, 2011
we do have 2 Rv042, one in my office and one in my house.. in the office we do have static ip and at home none.. question is can i connect the two RV042?
View 1 Replies
View Related
Mar 22, 2011
I have some problems in my network with Gateway to Gateway Vpn Connection using two Rv042 routers.
I cannot ping the computers with static ip configuration.
In local an remote computers who have DHCP ip configuration i can ping each other .
View 1 Replies
View Related
Jul 26, 2012
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
View 1 Replies
View Related
Apr 6, 2013
i am trying to setup a vpn Gateway To Gateway when i setup the vpn i can ping the 2 rv042 i cant see any computer in the network places when there comect we need to see the computer in the network places so are pos will run?
View 1 Replies
View Related
May 12, 2013
We're running LMS 3.2 with DFM 3.2, and at some point within the last month, email notifications from DFM have stopped flowing. DFM is trapping events as they occur and these are viewable through the portal, but notifications that should be going out as email and SMS messages have stopped.
[code]...
Backups going back beyond when this is believed to have stopped working are available if something needs to be restored. If that's the direction I need to go, how do I restore just the DFM portion of the database? If backup restore is not the way to proceed, what other advice can be provided.
View 1 Replies
View Related
Mar 6, 2011
I have an RV082 and a RV042. I have been able to successfully establish a gateway to gateway vpn connection between them both, and I can remotely administer each router through the VPN connection, but I am unable to ping computers from one side of the connection to the other. For example, a computer in the 10.10.1.0 subnet can't see / ping / communicate with a computer in the 192.168.1.0 subnet.
Below are the configurations for each. Aside from the static IP configurations and the VPN configurations, no other changes were made to the routers. RV082 DHCP Enabled Tunnel Status: Connected Local Group Setup
IP Only: X.X.X.66Local Security Group Type: SubnetIP Address: 10.10.1.0Subnet Mask: 255.255.255.0Remote Group Setup
View 1 Replies
View Related
Jan 29, 2013
Can a router using OSPF propagate that he is a router with default-information originate... at the same time when he got an own gateway of last resort to an IP-adress? If so, how? I can't get it to work.
View 8 Replies
View Related
Mar 16, 2013
It has email and alarm notifications. But what about sound notification through PC speaker?
View 1 Replies
View Related
Dec 20, 2010
I have been trying to setup my DIR-655 A4 (Firmware 1.34NA) router to send me email notifications on new firmwares, when the log is full and every Saturday. So I have a schedule already created for sending the emails on Saturday and I also have the option to send notification of new firmware checked. Now I have settings, similar to the following, under email settings.
View 14 Replies
View Related
Feb 28, 2010
setting up the email notifications. I need the log emailed to me during a certain time of the day and it wont email anything. Even when I am in the log and push the email now, it does nothing. I've tried setting it up through hotmail, lmsn live, and gmail. None of them work. What am I doing wrong or what do I need to do?
View 9 Replies
View Related
Feb 8, 2010
I am having an issue at one of our remote agencies whereas we are getting numerous mac-flap notifications on our switches. This has become kind of a hinderance as we are getting tired of seeing these messages. The end users havent been complaining.
It's usually occurring with the same mac-addresses over and over. Upon further investigation, we found the mac-addresses are all on laptops which have both wireless and wired nic's. There are wireless AP's (cisco 1242's) in use which they can connect. We also found where the error is popping up as they move from wireless into docking into their docking station which has a lan cable attached. I was under the assumption that the wireless mac and wired mac were different numbers and therefore if the wired was up simultaneously with the wired, as it switched over, they shouldn't get a flap.
View 6 Replies
View Related
Jul 22, 2012
Can I configure the 2504 to send email notifications for particular alerts? how?
View 2 Replies
View Related
Feb 22, 2010
DIR-655(A3) 1.33NAb02_HNAP_beta I used to be able to send notifications on log full etc... When my ISP was still allowing outbound email w/opt out of block on port 25. This worked on my old DI-524, and used to work on my DIR-655.In an effort to clamp down on spam my ISP formerly SBC now AT&T began requiring SSL. Secure Authentication is not required. With the ever increasing concern for controlling spam DLink really needs to get in gear and provide the support customers need and back the efforts of ISP's to control spam. Otherwise it's wasted code occupying space. On that note if space is a concern, need space for the code ~ throw SecureSpot out !
[URL]
On the Outgoing Server (SMTP) Settings window click Edit and verify:
# Server Name - displays smtp.att.yahoo.com.
# Port - displays 465.
Note: When updating the secure server settings, check SSL checkbox first to update the port setting.
* Under Outgoing mail (SMTP), the box next to server requires a secure connection (SSL) is checked. This works flawlessly with Thunderbird and other mail clients therefore it is clearly a shortcoming of the firmware on the DIR-655 i.e. no SSL? This is totally inadequate.
View 5 Replies
View Related
Sep 15, 2011
Where/how do we setup an SRP527W to send email notifications? Can't seem to locate the setting when logged in as admin.
View 1 Replies
View Related
Nov 1, 2011
I have a 4507R that will be using track and sla for failover/failback on two WAN circuits going out of my switch. Is there a way to configure an email notification, or some other sort of notification to let me know which route is being used, especially when the failover kicks over to by backup route.
View 2 Replies
View Related
Jul 19, 2011
I have 2 Cisco 5508 Wireless LAN Controllers.They are NOT connected to a WCS.Is there a way to configure the 5508's to send email notifications when an AP drops off line?Is not is this functionality available with either a WCS or new NCS?
View 1 Replies
View Related
Aug 15, 2012
MY voice conversation on magic jack breaks up when I download a movie to my direct TV. I have a Belkin F9K1103V1, N750Db. I'm not using WiFi, Im wired to ports on back of Belkin.
View 3 Replies
View Related
Mar 15, 2011
I have few queries abou the Cisco 880G series router.
1) Suppose if we have a 3G service enabled SIM card then can we insert the same on the Cisco 880G router and browse internet from the LAN of 880G?
2) I think the HSPA+ standard supports 84 Mbps downlink speed..... so is it supported on 880 G router?
3) Can we configure Cisco 880G as a CME?
View 2 Replies
View Related
May 12, 2011
I have a cisco2811 router and i want to convert or make it to be a voice enabled router? it has a current image/ios of (C2800nm-adventerprisek9-m), version 12.4(5a).
View 4 Replies
View Related
May 14, 2013
i hace a VPN configured between two Cisco ASAs, but I have a problem to reach a network behind a router 2800.
View 7 Replies
View Related
May 16, 2011
What's the best router / handset to get to practice for CCNA Voice?
View 2 Replies
View Related
Sep 6, 2011
Since I am new to VOIP and am getting confused with the responses online on how to connect to a commercial phone system I thought I would ask here. I have a small voice router (1751) running CME with 2 Cisco 7940 phones. I would like to hook it up to a commercial line, but not sure how to. What specific card will I need for my voice router to connect it to the outside world (FXO right)? I see where they talk about hooking it up directly to the LAN line, another using a commercial phone system, and then the others using a PBX,ect... So confused to say the least. I assume I need an FXO port to connect to the POTS, but not sure if there is anything else I’m missing in the setup...
View 4 Replies
View Related
Dec 21, 2012
When I try to configure a voice port (like voice-port 0/0/0:15) after doing a conf t, it gives me an error of invalid input detected.We are using a Cisco 3945. We have successfully setup 3825 and 2851 in the past.
View 2 Replies
View Related
