Am running LMS 4.0 on windows 2003 server, i would like to disable or remove notifications with the EventName 'ExceededMaximumUptime' and 'BackupActivated' on the device fault summary view. How do i achieve this? This will be useful in only monitoring fewer notifications.
View 3 RepliesWe're running LMS 3.2 with DFM 3.2, and at some point within the last month, email notifications from DFM have stopped flowing. DFM is trapping events as they occur and these are viewable through the portal, but notifications that should be going out as email and SMS messages have stopped.
[code]...
Backups going back beyond when this is believed to have stopped working are available if something needs to be restored. If that's the direction I need to go, how do I restore just the DFM portion of the database? If backup restore is not the way to proceed, what other advice can be provided.
It has email and alarm notifications. But what about sound notification through PC speaker?
View 1 Replies View RelatedI have been trying to setup my DIR-655 A4 (Firmware 1.34NA) router to send me email notifications on new firmwares, when the log is full and every Saturday. So I have a schedule already created for sending the emails on Saturday and I also have the option to send notification of new firmware checked. Now I have settings, similar to the following, under email settings.
View 14 Replies View Relatedsetting up the email notifications. I need the log emailed to me during a certain time of the day and it wont email anything. Even when I am in the log and push the email now, it does nothing. I've tried setting it up through hotmail, lmsn live, and gmail. None of them work. What am I doing wrong or what do I need to do?
View 9 Replies View RelatedWe have a 2800 router which is configured as a Voice Gateway. For some reason, yesterday we started getting DFM notifications like the one below. We seems to get an active messages every few 10mins or so, then a few minutes later the message will clear before becoming active again...
EVENT ID = 0009NK2
ALERT ID = 0000QTM
TIME = Tue 21-Jun-2011 16:06:50 BST
STATUS = Active
SEVERITY = Critical
MANAGED OBJECT = XXXXVG1
MANAGED OBJECT TYPE = Routers.
I am having an issue at one of our remote agencies whereas we are getting numerous mac-flap notifications on our switches. This has become kind of a hinderance as we are getting tired of seeing these messages. The end users havent been complaining.
It's usually occurring with the same mac-addresses over and over. Upon further investigation, we found the mac-addresses are all on laptops which have both wireless and wired nic's. There are wireless AP's (cisco 1242's) in use which they can connect. We also found where the error is popping up as they move from wireless into docking into their docking station which has a lan cable attached. I was under the assumption that the wireless mac and wired mac were different numbers and therefore if the wired was up simultaneously with the wired, as it switched over, they shouldn't get a flap.
Can I configure the 2504 to send email notifications for particular alerts? how?
View 2 Replies View RelatedDIR-655(A3) 1.33NAb02_HNAP_beta I used to be able to send notifications on log full etc... When my ISP was still allowing outbound email w/opt out of block on port 25. This worked on my old DI-524, and used to work on my DIR-655.In an effort to clamp down on spam my ISP formerly SBC now AT&T began requiring SSL. Secure Authentication is not required. With the ever increasing concern for controlling spam DLink really needs to get in gear and provide the support customers need and back the efforts of ISP's to control spam. Otherwise it's wasted code occupying space. On that note if space is a concern, need space for the code ~ throw SecureSpot out !
[URL]
On the Outgoing Server (SMTP) Settings window click Edit and verify:
# Server Name - displays smtp.att.yahoo.com.
# Port - displays 465.
Note: When updating the secure server settings, check SSL checkbox first to update the port setting.
* Under Outgoing mail (SMTP), the box next to server requires a secure connection (SSL) is checked. This works flawlessly with Thunderbird and other mail clients therefore it is clearly a shortcoming of the firmware on the DIR-655 i.e. no SSL? This is totally inadequate.
Where/how do we setup an SRP527W to send email notifications? Can't seem to locate the setting when logged in as admin.
View 1 Replies View RelatedI have a 4507R that will be using track and sla for failover/failback on two WAN circuits going out of my switch. Is there a way to configure an email notification, or some other sort of notification to let me know which route is being used, especially when the failover kicks over to by backup route.
View 2 Replies View RelatedI have 2 Cisco 5508 Wireless LAN Controllers.They are NOT connected to a WCS.Is there a way to configure the 5508's to send email notifications when an AP drops off line?Is not is this functionality available with either a WCS or new NCS?
View 1 Replies View RelatedIs there a way to get notifications (emails) when the external ip changes and the rotuer updates dyndns?i need to get an email about this change of ip. The only constraint is it has to work without a computer attached to the router as it would have to be powered on 24/7 So ip change notifiers like trueip or ipcheck won't work as they are programs that run in a computer.
View 9 Replies View RelatedWe're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.
I have a friend who is in need of a laptop or netbook only for word processing.
The device cannot have any possibility of connecting to the internet, and also cannot have a webcam. I may be able to find one without a webcam, but I think the possibility of finding one without a NIC wouldn't be easy, if at all possible.
I can only think that disabling the network adapter in registry edit will be something she won't be able to undo (she's not majorly tech savvy).
I've not purchased the laptop/netbook yet, but I would like to know if it's possible and/or how to do it before I buy it.
I have a customer who wants to disable cdp on all switches for securtity reasons. The same customer has also LMS 4.0 installed.
When disabling cdp, does it affect the topology services on LMS? Can you still see the topology tab on device manager or the topology map of the entire network?
I have a modem connected to my pc, and the ethernet can be removed and connected to a laptop to access internet. How do I prevent access to other laptops and computers?
View 4 Replies View RelatedRIPv2 And Disabling / re-enabling Interface
View 5 Replies View RelatedWe inherited a lot of the equipment from another team of network administrators and every now and then, we run into a switch with some old code or configuration that was left behind and missed by us. Today, I discovered that CPP was enabled on 3 of our access-layer switches in one of the buildings we support.
View 3 Replies View RelatedWe just recently upgraded a 5540 ASA running 8.2 to a 5555 running 8.6. I have a question concerning disabling proxy ARP with static nat rules in place. We have several instance where devices in a dmz have a static nat entry to the outside and a static nat entry to the inside using the same IP. My question is if we disable proxy arp on the inside interface would that cause device on the inside not to be able to reach the device in the dmz? From what I have seen you don't want to disable it on the outside interface due to all the static nat translations. But we have some that are have nat translation going to the inside as well. How does proxy arp come into play there? Below is a diagram of an example of the setup I a referring to. This is on the new 5555 running 8.6
View 1 Replies View Relatedmy company has used Split Tunneling for all of our VPN uses, however we recently purchased 2 ASA5505s for use at various jobsites, and have been running into problems with Local Network Administrators blocking certain traffic that we need to operate. They allow full VPN connectivity to traverse their networks, so we are able to use our LAN Resources over the split tunnel no problem.
We have it set up as a Dynamic L2L Connection, and this ASA is operating flawlessly minus the traffic being blocked upstream by the network admin. Our VPN topolgy is Hub & Spoke. Below is excerpts from our config on how the VPN is set up: [code]
What we'd like to achieve is being able to pass ALL traffic (LAN & Internet) through the VPN tunnel, then be processed by the Hub ASA (192.168.9.1) on the other end. I am guessing crypto map + routing would have to be changed?
access-list to_hq extended permit ip 192.168.101.0 255.255.255.0 0.0.0.0 0.0.0.0route inside 0.0.0.0 0.0.0.0 192.168.9.1Disable NAT on Spoke. Is this how I would go about doing this??? We need ip address dhcp setroute so our ASA can find the other end and form the VPN tunnel, and I am not sure how this would affect things. [code]
Any way to disable the usb console port on a 2900 series router?
View 2 Replies View RelatedI currently own a Lenovo Thinkpad x201 Tablet Laptop.The issue is that I randomly lose internet access after usage for some time. I've determined [but not limited it to] that the computer heating is causing the computer to automatically disable the connections. I've looked at the Drivers and have found that one of the Drivers disables itself and will not re-enable when I try to enable it again. When I try to reboot, it stalls on the Shutting Down screen indefinitely [I must force restart].
INTEL(R) 82577LM Gigabit Network Connection
INTEL(R) Centrino Advanced-N 6200 AGN
I've checked the BIOS, but I haven't found much of anything. After tampering for a while with it, I received a BSOD. After trying to boot it back up, I got the "a disk read error has occurred" screen and had to send it in... at which point they reinstalled the OS, wiped my hard drive, and sent it back.
I have the Motorola SURFboard SG6580 cable modem/wireless router combo. However, I'm only using my Linksys WRT54GL for the wireless functions. It's been my old standard for years, not to mentioned I have my entire wireless encrypted network setup via this device.
So, recently I've been trying to set up Port Forwarding and I've been having trouble getting sites like canyouseeme.org to see the port. After speaking with Tech Support at my ISP, they had me disable some of the settings in my SURFboard modem in order to deactivate the router side of things to get it act only as a cable modem. However, my port forwarding is still not working.
Here is a screen shot of all the pertinent screens of my SG6580 properties, and what they had me set. if I have properly configured the modem to not interfere with my other wireless setup so I can at least rule this out as what's blocking my port forwarding?
I am a teacher in a computer Classroom. We are on a school network and certain students abuse the internet privalages. Is there a way for me to restrict the internet for a certain computer in the network besides unplugging an ethernet cord?
View 2 Replies View RelatedWhat is the impact of disabling xlate in FWSM
We have dynamic NAT configured from inside to outside interface, but still it is showing NAT entry as below.
"NAT from inside:177.26.99.10 to outside:177.26.99.10 flags Ii"
Expected NAT entry should as below :
"NAT from inside:177.26.99.10 to outside:111.111.111.111 flags Ii"
We were considering implementing "ip verify revert-path" .Hence here i am thinking whether xlate-bypass is the issue here and implementing same with "ip verify revert-path" woud be a good idea.
where I can find the OID for enabling and disabling a port for the RV016 router? I performed a snmpwalk but I couldn't find it.
View 1 Replies View RelatedI have a Motorola SGB900 cable modem/router which up until now has done both functions. However i want to upgrade the router and so have purchased a netgear wnr2200. I have tried connecting to the WAN and LAN connections on the new router and disabling NAT and wireless on the old router in all possible configurations but i dont seem to be able to get it to work.
View 13 Replies View RelatedI have a central cisco SG200 26P switch, with about 20 ports going off to other network switches, and individual computers around the building.I need to keep the LAN functionality of the network, but I need the majority of the computers to not have internet access. But I also need to be able quickly re-enable internet access for a particular computer connected to a particular port if required.
View 3 Replies View RelatedI have a computer that I built a few years ago. Not sure of the exact specs, but for this question, I'm not really sure it matters other than the fact that I am a diehard XP fan. Guess which OS I am using. It does not have an onboard NIC, so I am using a NetGear WG111v2 wireless adapter that I got at just about the same time as the computer. I recently moved in with some friends and they have wireless internet. I hooked up my pc, and proceeded to connect to the internet. I got a good connection, but the dreaded "Limited or No Connectivity." First off, I tried disabling the connection and then re-enabling. This had no effect. So, like always, I do a power cycle. Same thing. Ipconfig gives me a 169.254.x.x, nonroutable, ip address. I release and renew. No good. Reset winsock. No good. Device manager says my adapter is working and drivers are up to date. In any case, I uninstall and reinstall it only to find the same results as before. There are three other computers on the network, one of which is my laptop, that all connect and are provided private ips by the router.
View 5 Replies View RelatedI no longer have internet access from my home network ONLY on my desktop computer. Everything was working fine as always - then while I was in my Network and Sharing Center, and clicked on my ethernet connection, 'Local Area Connection 3', I accidentally disabled it. No big deal I thought, so I re-enabled the connection. Except for some reason, my connection is all screwed up now. The name of this connection was and always has been 'dkm2' and now it just says 'Network', with no internet access. I have unplugged the cord and plugged it into this laptop and it immediately recognizes 'dkm2' and connects flawlessly, so I know the problem is on the desktop computer's end, and not the cable or router. I have tried reinstalling the ethernet adapter, as well as reinstalling/updating all drivers for it.The network diagnostic tool turns up with a message that says the connection between either my ethernet adapter or router and the Internet is broken. No matter what I seem to try, I can't get my connection to go back to it's normal 'dkm2' connection and stop giving me a generic, disconnected 'Network'. I can't figure out what could have changed. All that happened was the disabling and enabling of Local Area Connection 3.
View 9 Replies View Relatedcan you disable 3g adapter on board, and run a usb 802.11N wireless after disabling the 3g adapter?,
View 1 Replies View RelatedThere is a page in the DIR-825 that logs your computers IP and the other IPs it is connecting to. I was wondering if there was a way to disable that function on select devices? My handhelds and legitimate computers that should be on the internet are filling it with spam and it is hard to check for unauthorized users on the network. If that is not possible, then would I be able to completely disable the feature?
View 1 Replies View Related