Netgear WG111v2 - Disabling Connection And Then Re-enabling?
Jul 11, 2012
I have a computer that I built a few years ago. Not sure of the exact specs, but for this question, I'm not really sure it matters other than the fact that I am a diehard XP fan. Guess which OS I am using. It does not have an onboard NIC, so I am using a NetGear WG111v2 wireless adapter that I got at just about the same time as the computer. I recently moved in with some friends and they have wireless internet. I hooked up my pc, and proceeded to connect to the internet. I got a good connection, but the dreaded "Limited or No Connectivity." First off, I tried disabling the connection and then re-enabling. This had no effect. So, like always, I do a power cycle. Same thing. Ipconfig gives me a 169.254.x.x, nonroutable, ip address. I release and renew. No good. Reset winsock. No good. Device manager says my adapter is working and drivers are up to date. In any case, I uninstall and reinstall it only to find the same results as before. There are three other computers on the network, one of which is my laptop, that all connect and are provided private ips by the router.
View 5 Replies
ADVERTISEMENT
Feb 4, 2011
I no longer have internet access from my home network ONLY on my desktop computer. Everything was working fine as always - then while I was in my Network and Sharing Center, and clicked on my ethernet connection, 'Local Area Connection 3', I accidentally disabled it. No big deal I thought, so I re-enabled the connection. Except for some reason, my connection is all screwed up now. The name of this connection was and always has been 'dkm2' and now it just says 'Network', with no internet access. I have unplugged the cord and plugged it into this laptop and it immediately recognizes 'dkm2' and connects flawlessly, so I know the problem is on the desktop computer's end, and not the cable or router. I have tried reinstalling the ethernet adapter, as well as reinstalling/updating all drivers for it.The network diagnostic tool turns up with a message that says the connection between either my ethernet adapter or router and the Internet is broken. No matter what I seem to try, I can't get my connection to go back to it's normal 'dkm2' connection and stop giving me a generic, disconnected 'Network'. I can't figure out what could have changed. All that happened was the disabling and enabling of Local Area Connection 3.
View 9 Replies
View Related
Jun 12, 2012
I am using a desktop with a Netgear WG111v2 dongle to connect to my cisco linksys router.Basically my old modem died which was connected to a wireless router so we replaced it with a cisco linksys router and ever since the change ive been having difficulties connecting to internet on my desktop where as the the rest of the laptops in the house have had no problem. In the begining the desktop would always say its had limited connection the the network and such i couldnt connect to the internet but disconnecting the router several times and restarting the computer several times eventually the computer would have full internet access through the network without disconnecting at all.
A few days later the computer starting connecting to the network and gaining full internet access usually without turning of the computer and restarting it although i would disconnect from the internet every now and again for a minute or so and reconnect automatically this would happen more frequently when using Skype or msn messenger extremely frequent when using skype and especially when in a call.ive updated the driver of the wireless dongle to the latest version.my desktop is running vista while the laptops are running windows 7 and mac osx or whatever.ive also download a free version of avast and given a full scan of my computer without finding any threats.
View 4 Replies
View Related
Mar 12, 2012
RIPv2 And Disabling / re-enabling Interface
View 5 Replies
View Related
Oct 9, 2012
I purchased a WNDR3400v2 probably around two months back and since then I haven't had any issues with it. Now, I like to keep the security setting on WPA2-PSK for the security but my brothers and my own Nintendo DS don't support this security for connecting. So, since my previous router had a guest network, I decided to activate and deactivate that network with no security when it was needed (Half hour or less), and I haven't had any issues until doing this with the WNDR3400v2.
Basically what happens is, after disabling the guest network again, no wireless devices can connect to the router... PERIOD... Upon trying to connect it also says "You are unable to connect) right after it verifies the password. I spent a few hours trying to fix it but I haven't gotten anywhere really..
What I have tried-v
-Resetting the Router
-Powercycling the Router
-Resetting it to factory defaults and restoring previous settings
-Enabling and disabling the network
-Deleting the original network saved on the computers and connecting as if from a new network.
-Also tried restarting my computers
-Updating the firmware (For some odd reason I couldn't find any firmware last week..)
I researched it a bit and found some solid leads, but nothing that fixed the issue. The only "Fix" I could find was disabling the security and leaving it open.. Which I would prefer not to do for obvious reasons...
Router Type: Netgear Wireless Dual-Band N600 Router (WNDR3400v2)
Firmware: V1.0.0.34_1.0.52
View 2 Replies
View Related
Jul 20, 2011
where I can find the OID for enabling and disabling a port for the RV016 router? I performed a snmpwalk but I couldn't find it.
View 1 Replies
View Related
Jun 10, 2012
I have just logged into the ASDM for my 5520 and can see under the "Firewall Dashboard" tab that I can enable these graphs/stats, why would they be disabled? So I was wondering if I enable these and they use alot of memory how can I disable them again?
View 3 Replies
View Related
Oct 5, 2011
I have just logged into the ASDM for my 5520 and can see under the "Firewall Dashboard" tab that I can enable these graphs/stats, why would they be disabled? So I was wondering if I enable these and they use alot of memory how can I disable them again?
View 1 Replies
View Related
Nov 11, 2011
I have a Motorola SGB900 cable modem/router which up until now has done both functions. However i want to upgrade the router and so have purchased a netgear wnr2200. I have tried connecting to the WAN and LAN connections on the new router and disabling NAT and wireless on the old router in all possible configurations but i dont seem to be able to get it to work.
View 13 Replies
View Related
Jul 28, 2011
I have A wg111V2 NETGEAR WIRELESS USB ADAPTER AND HAVE FORGOTTEN MY SECURITY KEY PASSWORD HOW DO I RETRIEVE IT.
View 2 Replies
View Related
Sep 4, 2012
Any good WiFi card. As accordind to my network engineer my 6 year old Netgear WG111v2 has some problem as a result the connection continuously looses connection. Although in my Laptop which has onboard Wifi the connection is consistant. Out of internal and external Wifi card which one is more reliable?
View 9 Replies
View Related
Sep 23, 2012
Enabling TCP / IP connection between Windows CE 3.0 and PC?
View 1 Replies
View Related
Feb 16, 2013
My keyboard was broken so plugged in a USB keyboard that doesn't have a fn button. I must have accidentally pressed something as my comp is asking me to turn in the wireless capability. There is no button on the computer and the light for wifi is off. How to turn this back on with a keyboard that does not have a fn button?
View 1 Replies
View Related
Apr 26, 2012
I have two WS-C2960-24TC-L Switch with Software Ver 12.2(25r)SEE6 with image c2960-lanbase-mz.122-35.SE5.bin and 12.2(25r)SEE1 with image c2960-lanbase-mz.122-25.SEE2.bin currently on it.
I want to enable SSH connections on the switches and believe I need to import the cryto image onto the switch. I would like to upgrade it to new version that can also support ssh connection but not sure which image to download from cisco. The switches are now live.
System image file is "flash:c2960-lanbase-mz.122-35.SE5/c2960-lanbase-mz.122-35.SE5.bin"
cisco WS-C2960-24TC-L (PowerPC405) processor (revision H0) with 61440K/4088K
[Code].....
View 5 Replies
View Related
Aug 27, 2012
I have a friend who is in need of a laptop or netbook only for word processing.
The device cannot have any possibility of connecting to the internet, and also cannot have a webcam. I may be able to find one without a webcam, but I think the possibility of finding one without a NIC wouldn't be easy, if at all possible.
I can only think that disabling the network adapter in registry edit will be something she won't be able to undo (she's not majorly tech savvy).
I've not purchased the laptop/netbook yet, but I would like to know if it's possible and/or how to do it before I buy it.
View 3 Replies
View Related
May 20, 2011
I have a modem connected to my pc, and the ethernet can be removed and connected to a laptop to access internet. How do I prevent access to other laptops and computers?
View 4 Replies
View Related
Apr 27, 2011
Am running LMS 4.0 on windows 2003 server, i would like to disable or remove notifications with the EventName 'ExceededMaximumUptime' and 'BackupActivated' on the device fault summary view. How do i achieve this? This will be useful in only monitoring fewer notifications.
View 3 Replies
View Related
Aug 15, 2011
I have a Netgear wgr614v7 wireless router that has been working perfectly for a couple weeks now, but I have suddenly run into a problem. For some reason, I can now only connect one laptop at a time to the network. When I try to connect a second laptop, it says, "Windows was unable to connect to [network name]". When I try to connect with my Macbook, it says "network timed out".
View 3 Replies
View Related
Feb 9, 2012
I have installed the netgear N900 dual band which is 99� and is working fine on 2.45ghz because I have a belkin g range extender as my house is very long. So everything is working and my computer works but every so often the Internet drops so the modem needs turned on and off to get back on the Internet even though my computer says its connected but not loading any pages. It works fine for a while then sometimes drops, it works fine until I use my Mac books or iMac but works fine with iPhones? What can I do ?
View 2 Replies
View Related
Mar 26, 2013
Mediacom is my cable provider. They came out a few months ago and thought the problem was their Motorola modem. They replaced it with an RCA (Thomsen) which worked great for about 3 months.Now (3/13) I am losing my connection at least once a day.I started to download the new Netgear Firmware update, but in the middle of that, you guessed it, the connection dropped. So now my router is useless. There's probably a way to reset it, but I haven't found that yet. And so far the Netgear phone # is locked inside the router somewhere! I'm hard-wired to the RCA modem now, so we'll see. I have a feeling, after reading the previous thread, that my connection will be fine.I have my own cable modem, needed for a previous cable provider, and a new Netgear N600 2-frequency router.
View 2 Replies
View Related
Aug 25, 2012
I currently have a Netgear dgn2200 n300 wireless router (acts as a modem, you know all in one thing), and I have configured the settings on it so I can have an open nat type/port forwarded for gaming and so on. I have my xbox and the desktop connected to it via ethernet and my ipod and laptop connected wireless.
The problem is that the internet just drops out for a couple of mins every hour or so whether I or whoever is on it or not. I have tried changing the cables and filter for the phone line but nothing has seemed to work. Occasionally when the internet drops out it doesn't come back on so I have to unplug the router and so on to get it to work.
It's just starting to get annoying getting disconnected so often especially when the router cost like $200 and is supposed to be good for gaming and stuff, and I can't seem to find out why or isolate the problem. My internet download speed is fairly quick (I can get 1.5mb/s say when downloading a movie/hd youtube) and I get 70 GB a month.
View 5 Replies
View Related
Sep 24, 2011
My internet, after a few seconds of working right, craps out on me and I cannot figure out why. I am tempted to purchase a new adapter.My ISP is Comcast, I'm using T1, and I run AVG.
Quote:
Windows IP Configuration
Host Name . . . . . . . . . . . . : JamesBoothe-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 4 Replies
View Related
Aug 14, 2012
I bought a Netgear wnr2000v3 about a year ago and everything was running fine for months. There are 8 devices connected to the router, 3 directly connected, 2 over wifi and 3 passing a switch.
Now, since approx. a month, it happens like once a week that the connection to the modem crashes and I'm unable to access the internet for about 3-4 hours anymore. I'm still able to connect to the router, where it is stated that there's no internet connection. When I connect a pc directly to the modem, everything is fine, so there doesn't seem to be any problems with my ISP.
I updated to the last firmware, tried it out with only 1 device connected to the router, reset factory defaults, rebuilt the physical setup.. Is there a way to gain access to internal log files?
View 1 Replies
View Related
Aug 26, 2011
I currently own a Lenovo Thinkpad x201 Tablet Laptop.The issue is that I randomly lose internet access after usage for some time. I've determined [but not limited it to] that the computer heating is causing the computer to automatically disable the connections. I've looked at the Drivers and have found that one of the Drivers disables itself and will not re-enable when I try to enable it again. When I try to reboot, it stalls on the Shutting Down screen indefinitely [I must force restart].
INTEL(R) 82577LM Gigabit Network Connection
INTEL(R) Centrino Advanced-N 6200 AGN
I've checked the BIOS, but I haven't found much of anything. After tampering for a while with it, I received a BSOD. After trying to boot it back up, I got the "a disk read error has occurred" screen and had to send it in... at which point they reinstalled the OS, wiped my hard drive, and sent it back.
View 5 Replies
View Related
Oct 18, 2012
I have the Motorola SURFboard SG6580 cable modem/wireless router combo. However, I'm only using my Linksys WRT54GL for the wireless functions. It's been my old standard for years, not to mentioned I have my entire wireless encrypted network setup via this device.
So, recently I've been trying to set up Port Forwarding and I've been having trouble getting sites like canyouseeme.org to see the port. After speaking with Tech Support at my ISP, they had me disable some of the settings in my SURFboard modem in order to deactivate the router side of things to get it act only as a cable modem. However, my port forwarding is still not working.
Here is a screen shot of all the pertinent screens of my SG6580 properties, and what they had me set. if I have properly configured the modem to not interfere with my other wireless setup so I can at least rule this out as what's blocking my port forwarding?
View 5 Replies
View Related
Dec 12, 2011
I am a teacher in a computer Classroom. We are on a school network and certain students abuse the internet privalages. Is there a way for me to restrict the internet for a certain computer in the network besides unplugging an ethernet cord?
View 2 Replies
View Related
Feb 14, 2012
I have a customer who wants to disable cdp on all switches for securtity reasons. The same customer has also LMS 4.0 installed.
When disabling cdp, does it affect the topology services on LMS? Can you still see the topology tab on device manager or the topology map of the entire network?
View 4 Replies
View Related
Jul 9, 2012
I have a Netgear DGN2200 router/modem and have been having this problem for a while now. Every so often the internet will cut out for roughly 30-60 seconds. There doesn't seem to be any pattern to the connection losses and they can happen at any time in the day (overall it seems to occur every hour and a half, although it can vary). When the internet connection is lost, the little "!" triangle appears at the bottom right. I still have wireless access to the router itself. It also occurs on both my wired computer and the wireless computer. On the Netgear itself, the internet light will either flash rapidly green, or sometimes turn red for a short while. The Netgear is plugged via a splitter into the telephone socket. the old neatgear we had did the exact same thing before it finally died and no longer worked at all. Hence why we replaced it with this one. I also rang AOL about the problem, who said that there may be a problem with the line and that we should ring BT about it. We had the line checked and apparently the line was fine and was not the cause of the problem. Things I have tried include changing the router channel and I have tried changing the splitter in case that was faulty. Do you think it could be a DSL problem on AOL's end? It's possible that the drops coincided with a free upgrade they gave us for faster internet, although time-wise I'm not entirely sure.
View 6 Replies
View Related
Sep 10, 2012
I just recieved the netgear modem model 7550 from frontier. when i try to connect to the wifi i get a message saying that it is connected but there is a lock symbol on the wifi icon. i have entered in the password but it does not change anything?
View 1 Replies
View Related
Jul 17, 2012
I've been having a problem for a while now wherein my internet connection seems to randomly drop for anywhere from ten seconds to a minute, then come back online. It's been doing this over the lifespan of one router, and continued into the life of this new one I have, which is a WNDR3700v3 Netgear.
I called my ISP and they fiddled around with things on my computer, but the issue is still going on. Rather than slog through another three hours with them, does anyone here have any tips for what I might look into for the cause?
View 19 Replies
View Related
Aug 17, 2011
I use the internet wirelessly via a Netgear JWAGR614 (I guess this is the Japanese-market version of the WAGR614), which works fine with my old laptop, a Toshiba Dynabook running Windows Vista. When I use it to connect with my new laptop, however (also a Dynabook, using Windows 7 32-bit), the connection to the router will freeze every few minutes. (It still claims to be connected, but no data seems to get through.) It will then come back after about 20 seconds, or faster if I disconnect and reconnect manually.The connection of my other PC is not affected during this time, it is still transferring data normally even while the new PC cannot.
View 6 Replies
View Related
Nov 23, 2012
I've been living in the basement of my house. Our router and modem is upstairs and we have a 20 mb/s connection, but I just ran a speedtest from my room and it shows me that my connection is only at 2.47 mb/s, which is really weird. The router is nearly just above my head on the floor above me, so I can't see the problem.
View 3 Replies
View Related
Jan 20, 2011
I live in a college dorm that has pretty lousy internet. There is no WiFi, just 2 ethernet ports per room I own multiple wireless devices, so wifi is basically a must, but with a wireless router the connection is too slow to even play xbox live. A friend of mine mentioned that I could input multiple ethernets into my wireless router, so I was kind of hoping that was somehow possible, even though I am pretty skeptical. I have a Netgear WPN824N router
View 1 Replies
View Related
