Linksys Wired Router :: Cisco 880G And Planet MH-2001 But Transparent
Feb 3, 2012
As my main router i have the CISCO 880G with the ip 192.168.1.1 at the ethernet interface 0 and my WAN connection at my ethernet interface 4.If the other end of my cable from ethernet intrface 0 i put it to another device which has the IP 192.168.1.2 to its WAN port and define the DMZ port of that other device as transparent with rules to pass all but to register and filter some things.When i have them like this i cannot reah to neither CISCO neither other device with ip 192.168.1.2.
View 1 Replies
ADVERTISEMENT
Mar 15, 2011
I have few queries abou the Cisco 880G series router.
1) Suppose if we have a 3G service enabled SIM card then can we insert the same on the Cisco 880G router and browse internet from the LAN of 880G?
2) I think the HSPA+ standard supports 84 Mbps downlink speed..... so is it supported on 880 G router?
3) Can we configure Cisco 880G as a CME?
View 2 Replies
View Related
Dec 8, 2010
we are intending to purchase some 887G router for one of our client, but we not sure if it support "performance routing" or not. coz we don't see it on cisco's datasheet, and "cisco feature navigator" don't have that information.
View 4 Replies
View Related
Feb 5, 2011
i cant get access to my router IPX1900 after upgrade the last firmware version?
View 3 Replies
View Related
Oct 31, 2011
Our security department wants me to close tcp ports 2001,4001,6001 and 9001. Below is part of my configuration
Interface Fastethernet0/0
IP address X.X.X.x
ip access-group control out
ip access-list extended control
deny tcp any any eq 2001
deny tcp any any eq 4001
deny tcp any any eq 6001
deny tcp any any eq 9001
permit any any
When they do a scan outside the company network is still shows up open. I have tried both a ip access-group in and out and it never seems to hit the ACL. The scan being done is on the f0/0 ip address.
View 18 Replies
View Related
Sep 23, 2012
I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
View 5 Replies
View Related
Sep 19, 2011
I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies
View Related
Oct 11, 2012
My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies
View Related
Sep 14, 2011
I have a home network with a wired BEFSR41 that, for a variety of reasons, MUST be manually IP configured (DHCP off). All computers and other devices connected to it are manually IP configured. I desire to add a device that cannot be manually configured, and needs DHCP. I therefore need to daisy-chain two routers with the second one DHCP on (and manual IP connection to the main network). The new device needs two-way internet access, but doesn't care if it sees any other current network devices. I've tried several configurations, none seem to work.
View 3 Replies
View Related
Apr 11, 2012
I have a WAP54G in my basement shop, wired to our main router upstairs, which is a Linksys BEFSR81. I'm not sure if this is an issue with the WAP or the router.
I only use the laptop computer in the shop every couple of days, but I leave the laptop plugged in and on most of the time. I used to have the power settings such that it didn't power down completely even after a long time. With that setup, if i didn't use the computer for several days, it would find that the connection to the router had died. The wireless link would report that it had a solid connection, but I couldn't connect to anything. Power cycling the WAP always fixed this.
Recently, I decided to save some wear & tear on the laptop drive, and adjusted the power settings to go to standby after a couple of hours. Now, it seems I can't even go one day without losing my connection.
I am running the latest frimware in the WAP, and the router is version 3.1. I can't check the firmware version on the router at the moment, because the web interface is giving me a blank screen. I know from past experience that I will have to power cycle it to get it to talk to me again.
In any event, it seems like the router connection to the WAP is timing out. I set the router "client lease time" up to 10000 a while back when I first had this problem, but that is clearly not doing the trick.
View 3 Replies
View Related
Jun 16, 2011
I have an old BEFSR41 ver. 2 wired outer that I'd like to use with a motorola modem/router as a hub. Is this doable?
View 2 Replies
View Related
Apr 19, 2009
BEFSR81 v3.0.I selecting Enabled UPnP and now I cannot access the router. When I enter the default admin for the password in the Authentication Required screen. I get the following screen: 401 Authorization RequiredThis server could not verify that you are authorized to access. Either you supplied the wrong credentials(e.g., bad password), or your browser doesn't understand how to supply the credentials required.I didn't enter anything new into the username or password fields.
View 5 Replies
View Related
Jan 14, 2011
Have an Actiontec GT704 feeding DSL into a BEFSR41 which is connected to a WRT610N. Can access internet, modem and wired router from desktop. Can access wireless router from laptop. Cannot access internet from laptop or wireless router from desktop. Changed ip address for wireless router to 192.168.2.1 so no conflict with modem or wired router.
View 3 Replies
View Related
May 9, 2011
How to connect two PCs and one DSL router to get on the internet?I am getting IP conflict error on the PC. I can only connect one PC at a time to get to internet.
View 1 Replies
View Related
Jun 23, 2012
I have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can access clients which are connected to router. I have added rules also in firewall.
View 1 Replies
View Related
Nov 10, 2011
I've installed a RV042 and my terminals cant even ping each other. They have Internet, but they cannot ping each other, or open network shares. It is not a dns problem becouse it does not work with the IP.
View 1 Replies
View Related
Mar 16, 2011
I need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies
View Related
Nov 28, 2011
I just bought a new Linksys E4200, and connected it about an hour ago. I have a 30Mbps internet connection when connected direct to the modem, but when connected wired to the router, max speeds are 8Mbps.
View 2 Replies
View Related
Jun 7, 2011
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies
View Related
May 9, 2011
I have been trying to find out what the maximum Wan to Lan thruput is for the Linksys Cisco BEFSR 41 Etherfast router..
Have both the version 3 and 4 models and want to deploy them into both 6mb and 12mb DSL networks.. From what I have found the version 1 and 2 have 10mb wan ports and the version 3 and 4 have 10/100mb ports.. There seems to be hardware upgrades as well with the CPU and memory speeds but what they are I do not know for sure.. Found someone stating that they went from a 50mhz CPU to a 166mhz CPU to a possible 220mhz CPU...
View 3 Replies
View Related
Apr 25, 2013
i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
[code]....
View 2 Replies
View Related
Nov 1, 2012
I bought a cisco 881 router exactly like the one I had . It was configured the same way but cannot get connected to internet.The new router settings do not have an NAT on it, my IT guy turned it on through the console port and we till cannot get it to work?
View 2 Replies
View Related
May 7, 2012
Is it possible to run the EA4500 as a Wired only Gigabit router? To do this do I just go into the settings and disable both the 2.4 and 5 channels or do I have to do something else?
View 2 Replies
View Related
Feb 7, 2011
I have a BEFSR41 that has been flawless to date but it is version 1 (I think). I have gigabit nics on all PCs but I am wondering if the old version 1 is only capable of 10mbps throughput. If that is the case then it may explain why I can get up to 20mbps download speeds off the modem and under 10mbps off the router. The router has the latest firmware and otherwise no problems.
View 2 Replies
View Related
Jan 11, 2011
we have two desktop Pc's both hard wired to a Linksys router. One P.C is on Windows 7 system the other is on Vista. The windows 7 is connecting O.K. The one on Vista is showing " Does not have a wireless network adaptor, install & configure. The Vista P.C. was working O.K. a couple of days ago.Also not connecting to a laptop from the host computer on the Vista system?
View 2 Replies
View Related
Mar 16, 2011
I have the setup disk and want to set up a password for the router. Don't want to mess things up since the system was installed by a pro. How do I simply enter a password to be used to connect?
View 3 Replies
View Related
Jun 18, 2011
My router was not functioning well so I decided it might be a good idea to reinstall the driver package via the admin upgrade page. Since then it doesn't work at all. The power light flashes constantly now.
View 9 Replies
View Related
Oct 16, 2011
I have an AT&T Univese which is class G. I want to run it in class N.Do you think plugging my Linksys router into the AT&T will give it to me(class n)?If so, how do I get the linksys parameters set up? It giving wrong readings at its not connecting to the internet.
View 3 Replies
View Related
Dec 20, 2008
I just installed an RVS4000 router for a SOHO. I have no problem getting out to the internet so access from LAN -> WAN is working fine. The problem is with VPN access from the WAN.I created a VPN account and set up QuickVPN on a PC making sure I imported the certificate. I can connect to the router with no problem and I can even connect to the routers web admin page.But that's where it ends. I cannot connect in any way, shape, or form to PCs on the LAN through the VPN. I can't even ping them.Am I missing something in the setup of the router?
This is the only reason I bought this router as the old one was working fine. How to fix getting through the router to connect to the computers on the LAN.
View 9 Replies
View Related
Apr 1, 2011
I have just changed from cable to DSL. I have a LinkSys BEFSR41 router. I can't get my LinkSys BEFSR41 router to work with the DSL.
View 3 Replies
View Related
Jun 29, 2011
LinkSys BEFSR41 v3 4-port cable/dsl router
Ubuntu linux 11.04 'natty'
Verizon dsl internet connection
I'm unable to log into the 192.168.1.1 router using the default user/pwd of blank/admin
View 2 Replies
View Related
Feb 14, 2011
My internet supplier is Comcast. I have a problem with a URL that will not load or I could not connect to that site. Comcast said it was my router that was probably the reason. I have not had any problem in the span of using this model and version before. Should I be looking for firmware upgrade or a new router? Operating system is MAC OSX 10.5. Using router to network 2 MACs.
View 5 Replies
View Related
May 15, 2009
I am trying to set up a dual WAN on my RV082 - I have Verizon DSL on WAN1 and I am trying to establish Time Warner Road Runner on WAN2 as a backup in case DSL goes out on WAN1.I cannot get the router to recognize both connections at the same time. I have power cycled everything, the router is only picking up one internet signal at a time.
View 3 Replies
View Related
