Cisco WAN :: 800 Series Router Auto-sense ATM Pvc
Jan 30, 2012
Some of which use snap and some use mux, the router is the one will start the connection and will always be on, untill there is a power cut, if there is. At this point when the power comes back on and a packet's destination is the outside the router should initiate a connection over the atm.
•Do not use this feature on a router that initiates PPPoA sessions.
•This feature supports ATM PVCs. Switched virtual circuits (SVCs) are not supported.
•PPPoA does not support static IP assignments within virtual templates.
The second and thrid I can understand and the 3rd will just get assigned an IP address from the ISP.But with the first point how is it possible to set this up when the router cannot initate the connection?
View 1 Replies
ADVERTISEMENT
Apr 1, 2013
We are facing cold start issue on 4500 series switch. The switch is restarting automatically almost weekly twice or thrice.As per show tech. output , there is "cold start log".Please find the attached logs for your reference.After time change , auto restart happening & am not found any log for power failure also.
View 6 Replies
View Related
May 10, 2013
i have Cisco ASA 5550 and i want to do URL filtering using Web sense,can i use Micorsoft Forefront TMG2010 as websense server to do that?
the idea is to filter the HTTP & HTTPS URLs,if the Micorsoft Forefront TMG2010 is not suitable,refer to suitable Websense URL filtering server?
View 2 Replies
View Related
Dec 8, 2011
I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies
View Related
Jun 2, 2012
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies
View Related
Jan 17, 2011
I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies
View Related
Apr 27, 2011
I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.
View 1 Replies
View Related
Oct 18, 2011
I have a 7604 Edge router that connects to our Data centre via Fiber.
but i keep getting input errors on the interface Gi3/5. i also found out that i cannot change the duplex settings on the edge router to auto, i only have two options of full and half and changing it has not worked either.
I have tried to use a switch in between the fiber modem and the edge router to try to manipulate the duplex settings, but when i tried it the port simply shutdown and then i have to reverse the configuration.
The software version of the router is 12.2(33)SRE3, i really need to sort this out as connection to and from the Data centre is quite slow.
View 3 Replies
View Related
Nov 28, 2011
Is it possible to auto-shutdown for netgear router
View 1 Replies
View Related
Apr 21, 2011
I am trying to sort out an IP problem on my mates PC. I have setup a Linksys wireless router on his home broadband and it works fine with my laptop and gives me a DHCP address. When I try to connect his home PC either with a wireless dongle or ethernet connect it gets a Public IP address through the router and not one of the DHCP addresses. Even if you give it a static IP address and setup the router to accept it when you turn the PC on it still gets this public IP address. It is associating with the wireless router but only gives a local connection. I have done the ipconfig and it just renews the public IP address to a different one
View 3 Replies
View Related
Jan 30, 2013
I'm just wondering if there is any documentation that confirms if the 2 built-in Gigabit ports on a Cisco 2851 router support (or otherwise) auto-mdix.I can find information for the modules but not the 2 built-in ports.
View 3 Replies
View Related
Apr 11, 2012
I usually put some stuff up for downloading and go to sleep. Now I setup my computer to auto-shutdown at a particular time via cmd, but I want o know whether it is possible for me to put some time settings in my modem+router so that it switches off at a particular time or something like that.Then when I get up next morning, start using it again. I don't want to keep my router on after it's not needed. Also I don't wanna keep it vulnerable after it's not needed, even though I have set it up quite securely. ( WPA2 PSK, and MAC filtering)
View 5 Replies
View Related
May 9, 2013
My Cisco 3900 router is not taking the no auto summary command?
View 5 Replies
View Related
Dec 14, 2012
Region : Malaysia
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.13.12 Build 120703 Rel.58323n
ISP :
I'm using the TL-MR3220 hardware version 2.0. Firmware version 3.13.12 Build 120703 Rel.58323n. I'm using D-Link DWM-156 3.75G HSUPA USB Adapter.The problem I'm encountering is the router does not auto detect the 3G USB adapter when I power up the router. The router will detect the 3G adapter only when I plug out and plug in the 3G USB adapter. I used to have the same router but version 1.2. Version 1.2 does not have this problem.
View 4 Replies
View Related
Aug 5, 2012
we are busy with a local service provider ( ISP ) and they want to evaluate the SRP500 series and have a few questions that i cant answer clearly.
Can the router auto provision back to the ISP's site , aside from the USB bootup option. i.e manufacture programmed "version "to dial into a specific ISP to provision.
Central administration of SRP500 series: Can the ISP manage and update/ close down SRP500 from a central point. I know the TR069 is std on the SRP500 series, but what does this encompass.
View 1 Replies
View Related
Aug 20, 2011
I'm a bit confused about what a wireless range extender gives me. I have bought a Sitecom Wireless Range Extender 300N. This extends the wireless range of your router to parts of the house that have a weak signal or none atall.
It is setup correctly and is working fine, however, the SSID is different from the Router.
Essentially, I want to extend the range of my router to parts of the house that have a low signal. This range extender seems to be the correct product to do this. However, I want my clients to switch to the appropriate wireless access point (either the range extender or my router) depending on the strongest signal, how can this be configured?
When a client is the overlap area (the area where both the router and the range extender can be sensed) I want the client to switch to the strongest signal.
In my case My Router is in the loft and the range extender downstairs. You can still get a low signal from the router when you are downstairs but the range extender give a full signal. However, I dont understand what makes a laptop 'switch' from router to extender when its downstairs.
Because the extender has a different SSID a laptop that can still get a low signal from the router when downstairs doesn't automatically attach to the extender to get a strongest signal.
If I set the extender to have the same SSID as the router
View 1 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Jul 24, 2012
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies
View Related
May 27, 2012
My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies
View Related
Jun 14, 2011
Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies
View Related
Apr 25, 2012
Any direct download of the EA2700 firmware upgrade. My inet is not dsl or cable and will not let the wan port connect, therefor the "auto firmware update" will not work. I'd like to update it and see if it fixes it before I return this for a dlink. url...Anyways, I just want the firmware link so I can decide if this thing is going back to the store or not.
View 1 Replies
View Related
Apr 16, 2013
Purchased an EA4500 router. I'm using an old HP 4L laserjet and have it connected to the router via the USB port. I have 2 Mac's and installed vusb on both. I can successfully print from both Mac's, however I have to manually disconnect and connect the printer in the vusb client. I can't get the auto-connect and auto-disconnect settings to work by themselves. Any guidance on the proper settings here?Additionally, do I need to configure the printer driver though the vusb client? When I click "configure", I get an error saying"Cannot connect to Prolific Technology Inc. IEEE-1284 Controller.
View 3 Replies
View Related
Jun 18, 2007
How to change or modify the auto generated network key? I am trying to work around but no luck. Is there a way to do this or once you generate a network key it is a default.
View 5 Replies
View Related
Nov 15, 2012
I have an E3000 Dual Band. On my 5Ghz channel, I can select Auto(DFS) or I can manually select a channel.First of all, what does the DFS stand for? My 2.4 GhZ channel only has Auto, not Auto(DFS).
Second, when I select Auto(DFS), my wireless speed defaults to 144Mbps, and is only a single channel (I can see it in the in SSIDer utility). When I manually select a channel, no matter what channel it is, I get 300mbps and I can see that the signal is two channels (for instance, 36+40). Why Auto(DFS) doesn't automatically select the best channel and fastest speed?
View 2 Replies
View Related
Aug 10, 2011
I flashed the firmware and the ipv6 automatic is on disabled and I cannot set it to enabled.the 6rd tunnel option I can change but that has not effect- in fact from what I looked up it seems to be something used by some cable providers.hate to have to reset the router to factory defaults and then reset the network up - just to see if i can get the option to set IPV6 auto to enabled.
View 3 Replies
View Related
Jul 27, 2009
I m having 2500 series router. when i boot router automatically get into router(boot)> . how to solve?
View 6 Replies
View Related
Jun 18, 2012
Can i do sub-interface in cisco 891 or 881 series router ? 1900 and 2900 series router support sub-interface ?
View 1 Replies
View Related
Sep 18, 2012
i am proposing cisco 892 series router for multi VRF Configurations-MPLS. Is there any challenge you foresee in this architecture.
View 4 Replies
View Related
Jul 2, 2012
I have a router 819 with 3G built-in. Are there any manual for how to setup the interface celluar 0 for this router out there? I have Verizon as my 3G provider.
View 4 Replies
View Related
Oct 18, 2012
I am looking for the best QoS method for a 7600 series router. We have a 7604 edge router that has remote branch connections to it via GRE tunnels. unfortunately I cannot shape on these GRE tunnels neither can I use bandwidth or priority statements.
View 1 Replies
View Related
Sep 4, 2012
I have just bought my first non-domestic router, a CISCO 887VA-K9 which needs basic configuration to get it working. I have a copy of the configuration guide (334 pages) and CP Express user's guide (94 pages) and have spent an hour reading but either they are missing something or my brain is too small to figure out step 1. How to get started. Perhaps from where to download a CP Express installation kit for Windows.
Is the only way via a terminal emulator connected via a serial port ? Is there a graphical interface I can use ? Are there any basic tutorials for beginners ? This is probably the only non-domestic routrer I shall work on so I don't want to invest in a full training course. I just need enough to plug in the ISP credentials and set up DHCP.
View 27 Replies
View Related
Jun 9, 2013
load balancing and automatic failover between two isp
View 13 Replies
View Related
May 16, 2012
I have been able to put two Linksys routers in series no problem but this doesn't seem to work with an RV042.I have a number of customers that need to connect to a private email network via a router based VPN, but since VPN traffic is not filtered in the firewall, I would like to use an older Linksys router to manage the VPN(s) and have it pass data in through the filters of an RV042 on the DMZ port.I am getting stuck on the very frist part of this. Although I can connect to both the RV042 and LinkSys directly (by adjusting my subnet), I cannot ping the Linksys when it is connected through the DMZ port even if I disable the RV042 Internet port.
I know both the Internet and DMZ ports work on the RV042. I suspected that perhaps the RV won't pass through private IPs and tried known available pubic IPs instead of the 192.168.2.x subnet, but still no ping.What would be limiting the RV in this case? Is is possible to setup the RV to work in series with another router? Is there any other way to filter VPN traffic?
View 6 Replies
View Related
