I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.
I have come across articles mentioning that URL Filtering can be implemented by using ASA 5505 with URL Filtering Servers. But Websense and other Web Filtering Servers are paid ones ? Are there any free solutions available ? What exactly is N2H2 ? The reason is I don 't want to increase the CPU utilization of ASA by implementing URL filtering within the device. If I have around 30 nodes which connects to the internet via a 2Mbps line through ASA 5505 and if I want to block around say 10 or 15 URLs , will it increase CU utilization beyond permissible limits ? Currently the CPU Utilization is around 10 - 15 . Here's the infrastructure setup .
Some of which use snap and some use mux, the router is the one will start the connection and will always be on, untill there is a power cut, if there is. At this point when the power comes back on and a packet's destination is the outside the router should initiate a connection over the atm.
•Do not use this feature on a router that initiates PPPoA sessions.
•This feature supports ATM PVCs. Switched virtual circuits (SVCs) are not supported.
•PPPoA does not support static IP assignments within virtual templates.
The second and thrid I can understand and the 3rd will just get assigned an IP address from the ISP.But with the first point how is it possible to set this up when the router cannot initate the connection?
i two 5550 firewall set up for redundance purpose . in failover we define two different ip add one for primary and one for secondary .interface Ethernet0/0 nameif outside security-level 0 ip address xxxx.0.0.0.1 255.255.255.0 standby xxxx.0.0.2!interface Ethernet1/0 nameif inside security-level 100 ip address 10.0.0.12 255.255.255.0 standby 10.0.0.11.default gateway for host will be 10.0.0.12 (primary fw address) however in case of failover , the secondary fw will be up with ip address that was assigned for primary .in this case the secondary ip add 10.0.0.11 is actually nerver used? similarly do i need to have two public ip address for outside (one for primary and one for secondary ) ? or in case if primary fails the secondary comes onlie and take the ip of primary fw . hence i only need to purchase just one ip address.
I am having two ASA 5550 firewall running in active/standby mode. With in last two months our secondary firewall got down automatically 3 times. Firewall is running with IOS version 7.1.2. how to proceed further troubleshooting because there are not any logs on firewall.
I've been trying to configured Websense urlfiltering using ZFW feature on my Cisco 881G router. The router is running on IOS 15.0(1)M with Advanced IP Services. And I have confirmed it supports urlfilter feature.
This is what I tried to accomplish but IOS version 15.0x seems to have different command set. ----------------------- class-map type inspect httptraffic match protocol http parameter-map type urlfilter param server vendor websense 10.20.30.40 [Code]...
I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
I have ASA5550 ruuning Version 8.3(1) with inside and outside interfaces as below [code] On the inside : I have a server (10.20.10.36) that need to be accessed from an outside host (Y.Y.131.34) , so I have the below NAT/ACL rules. [code] is it right that I have to add two ACL entry for outside host to the NATed IP of the inside server , then again add another ACL entry from the same outside host to the private IP of my inside server o get this communication done?
we had just installed our ASA 5550 with IOS 8.0(2) a couple of week ago.
2 interfaces from each slot are being used ie 0/0 for Branch users comming via MPLS cloud , 0/1 for internal LAN users comming form Core Switch & 1/0 for Server farm LAN , 1/1 for Internet (outside)
the first 3 interface are considered inside with sec set at 100 while the 1/1 is outside with sec at 0.
Last night it suddenly started dropping all connections without any warning or any noticible log form the ASDM logging.
the connection drop would happen for 2 - 3 minutes and would work fine for the next 15 minutes or so..
after conencting the console , we found out that the IOS would suddelny go abrupt and show this display ...
TP-ASA(config)# TP-ASA(config)# TP-ASA(config)# Thread Name: Dispatch UnitPage fault: Address not mapped vector 0x0000000e edi 0x24d184b0 esi 0x0000000d ebp 0x1c6ceaf8 esp 0x1c6ceae0 ebx 0x09e965e0 edx
I have looked in the books I have (Cisco ASA, PIX and FWSM; ASA 8.0) and googled a good bit but can't seem to find any specific mention of how to do NAT exemption with v8.4. It seems NAT exemption (NAT 0 access-list) was deprecated. Using ASDM, there's no corresponding menu item for this that is obvious.
We have public addresses inside the ASA and want to allow in/outbound connections using these IP's without NAT. The ASA is a 5550.
I need to understand if ASA 5550 ver 8.2(1) is comptible with IPv6, if not what is the upgrade path to make it IPv6 compatible. The requirement is dual stack of IPv4 and IPv6 should run in the same HA cluster and later will shift IPv6 completely.
The existing infrastructure is equipped with ASA with HA Active/Active mode. The command output for required details are attached here in txt mode.
I have Active Standby ASA5550 setup with VPN premium license. A few days back we had a requirement of SSL VPN connection for and we got a temporary from Cisco for same, this license expired and the ASA reverted to it's original license. 3 4 days after this we saw a sudden increase in CPU utilization (upto 90% + -5%) on the ASA during production hours but were not able to figure out the reason, in order to restore the services we failovered the firewall to secondary and everything worked fine. We were suspecting one of the following but there were no logs for any of this
1. The ASA hardware was haivng problem
2. Some client was doing a DoS attack to bring down the ASA (no logs for this as well).
We took a downtime to look further by failovering the ASA back to primary and it worked fine without any issues ruling out the 1st option. We also came across a licesing doc [URL]
Downgrading any license (for example, going from 10 contexts to 2 contexts).
# Note If a temporary license expires, and the permanent license is a downgrade, then you do not need to immediately reload the security appliance; the next time you reload, the permanent license is restored.
As per this doc, sooner or later a restart was required on the ASA. We restarted secondary ASA and everthing was fine but when we restarted the primary ASA by swtiching over to secondary some of the server (not all) in the DMZ stopped working (even ICMP unreachable) and only came back to normal when the primary ASA was restored and working fine (with failover).
The reboot was done by shuting down the physical link between the Core switch and ASA inside individually.
I am not sure what could be the issue that the servers in the DMZ wen unreachable.
In my Cisco ASA 5550, I need to set two different syslogs servers, and I need to send the system logs to the first one (only admins login/logout), and the traffic logs and all the rest (informational level) to the second one. Do you know if is it possible or not and, if yes, how to configure it?
I would like to work with two ASA's 5550 in HA (Acitve-Standby) like perimetral firewalls and also work with another ASA 5540 but like a SSL VPN Remote Access to end users.Which will be the best topology to this scenary?. Perhaps i need to put the ASA 5540 SSL VPN together with the ASA's in HA directly in a port.
I am using an ASA5550 for a complex secure network that has at least six "outside" networks. Each "outside" network is assigned to a specific port each set at level "0". I also have a DMZ, set to level "50". I am having difficulty with passing traffic from a host in the DMZ to all but one of the "outside" networks. Is there a limit to the number of "outside" interfaces? I will provide a redacted config file as soon as possible.
I have the following problem, right now we have an ASA 5550 connected to the client´s side. A reset is being received on the client´s side, but when we run the sniffers on both extremes of the network, we can see that the reset is not being sent by the server´s side.
We have narrowed it down to the 5550 ASA, but have found no bug that matches the description.
The characateristics of the reset packet are the following:
- It is the only packet with a TTL of 255.
- Both server and client have very different window sizes, and the reset packet even though has the server´s ip and port as source of the packet, it has the client´s window size.
- It has a correct ack number.
-Before the reset is received, there are a couple of retransmissions of the last packet sent.
- We´re handling a VPN tunnel between both servers.
i m looking for asa 5550 product.Part # ASA5550-BUN-K9 - Cisco ASA 5550 Appliance with SW, HA, 8GE+1FE, 3DES/AES
1) does 5550 contains built in CSC / IPS modules.? why i m asking because the "quick refrence guide " indicates that expansion slots are not available.
2) can asa 5550 natively protects natively against networks attacks against virus / worms etc with out CSC OR IPS MODULE.?
I cannot logon with adsm anymore.when I run adsm, I type in my pw, and the screen keeps displaying "contacting the device". No timeout, just stays this way.I've updated the java version, no luck.I can connect with SSH with no problem. device = asa5550, 8.2(1) asdm 6.2(1) [code]
notice that there is no "with cookie-based authentication" here -- is this relevant?
I have an issue were thousands of connections on the ASA are marked with flags E, below is a visual of the connection. Any ideas what could cause this marking? Also, I can't grasp what the meaing of an outside back connection (ie flags E).
I have a couple of ASA5520 and ASA5550, and I wanted to know if it is worth it to upgrade the software from 8.2(4) to 8.2(5)? Because of the RAM I cannot upgrade to 8.3 for now.
I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin Source file name []? asa804-k8.bin Address or name of remote host [192.168.10.2]? Destination file name [asa804-k8.bin]? Writing file tftp://192.168.10.2/asa804-k8.bin... !%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect) Cisco asa#
My interface is 1GB, based on the above command, it is full?If interface is full, i have a problem! All the ports on asa firewall are using, how do resolve this? I can compress all data on this interface with class maps and policy maps?
We are having Cisco ASA 5550 appliance. from some days i am not able to access this ASA using ASDM. I am able to access ASA using SSH.[code]
At the same time standby firewall works perfectly fine with ASDM. I have tried by reloding the firewall, then it worked for 2 days & again stopped working.
Our users are using Xmanager to connect to a NNM connection which is going through a Cisco ASA5550 with 8.3. The session of Xmanager is getting terminated exactly after 1 hour and the users have to reconnect it again. How can we make the session to be up always, when I am bypassing the Firewall its always up.
Could URL FIltering be implemented on Cisco ASA 5505-BUN-k9?i mean to block certain websites, like facebook, youtube, to block certain download files like .exe, .com .bat etc....Is there any extra license needed for this, or it could be done with the simple IOS ASA5505-bun-k9?
I try to implement the url filtering feature on a cisco 2811 router and whenever i enable the parameter map patterns the router retuns (after some time)
%Unable to compile obj regex.[code] The result is that the router blocks ALL webpages without giving a block page message.
I have a problem configuring url filtering on ASA 5505 rel 8.3.1: I have to block the web navigation to facebook and, with my configuration, it works fine.The problem is when I try to access on other sites where there are a links to facebook, I cannot see that site and not only the button of facebook.