Cisco Firewall :: ASA 5550 Active / Standby With SSL VPN
Jun 12, 2011
I would like to work with two ASA's 5550 in HA (Acitve-Standby) like perimetral firewalls and also work with another ASA 5540 but like a SSL VPN Remote Access to end users.Which will be the best topology to this scenary?. Perhaps i need to put the ASA 5540 SSL VPN together with the ASA's in HA directly in a port.
I am in the process of adding a new ASA 5550 as a standby box to an existing ASA 5550 running on transparent mode. Both are on version ASA 8.0(4) and ASDM 6.2(1). I have set the new ASA 5550 to transparent mode. The configurations are the following for the HA: [code]My questions are the following:
1. The management ip address is different than the ip used for the failover link. Since the firewalls are on transparent mode, does the failover ip needs to be the same as the management ip address?
2. Does any other additional config is needed for HA to work for basic active/stand-by failover?
3. Which is the best method to add the second box without disrupting the active box?
I want to implement Active/Standby cluster with a pair of 5550 ASAs and I have a licensing question. Here is the "sh activation-key detail" output from both devices...
sh activation-key detail: Serial Number: XXXXX No active temporary key. Running Activation Key: XXXXX XXXXX XXXXX XXXXX XXXXX
This platform has an ASA 5550 VPN Premium license.The flash activation key is the SAME as the running key.So it looks obvious that I'll have to upgrade the first ASA to support 25 SSL VPN Peers in order to build HA cluster, right?Now I want to know do I need the "ASA5505-SSL25-K9" license or something else.
I have a pair of ASA 5520s operating in failover pair as active/standby, having two contexts on them. I am planning to share the load and make it active/active making first context active on the primary unit and second context active on the secondary unit. My question is if this will disrupt any connectivity thru these firewalls when I do "no failover" on the active/standby and assign the contexts to different failover groups and enable the failover back.
failover lan unit primary failover lan interface failover GigabitEthernet0/3 failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2 failover link failover GigabitEthernet0/3 failover
failover lan interface failover GigabitEthernet0/3 failover interface ip failover 192.168.3.1 255.255.255.0 standby 192.168.3.2 failover lan unit secondary failover
In the above configs is it i m missing something for failover? when i shut the INSIDE interface of Secondary ASA I get the below output, It shows me secondary failed and primary Active, WHY it is showing me FAILED instead of STANDBY/READY. What i know about firewall failover is when active goes down the other becomes standby unit but in this scenario it is showing me FAILED,
FW0001(config)# sh failover Failover On Failover unit Secondary [Code] ....
I am having a curious problem with two Cisco ASA 5550. They are configured in Active/Standby failover and in routed mode.The problem is: I cannot connect via SSH to the ACTIVE unit, only to the STANDBY. If a switchover is forced the problem is still the same. because it happens both with the primary and the secondary unit.It is not a L2 or a transport problem, because I can ping or access both units via ASDM.
with the 5550 we get 4 gig ports on slot 0 and 8 gig ports on slot 1, also a fast Ethernet management interface port. The documentation states that only 8 ports can be active at any one time but does that exclude this management port so that I can use this as well ?
Also is the port assignments for slot 1 like g1/0 - 1/7 ? As the other the 8 ports in slot 1 are 4 x gig E and 4 x gig sfp.
the first unit is currently working, and i now wish to configure the second unit as standby. im configuring through the ASDM GUI. Started the HA Wizard, choose Active/Standby configuration and enter the IP of the peer device. checks come back all ok. On the LAN link configuration page (step 3of6) Interface is pre selected as VLAN99, I give it a logical name as iface_fail, and enter 10.0.0.1 as primary address and 10.0.0.2 as standby, subnet as 255.255.255.248, and select port Ethernet0/5
Note that if i click on the buttons next to the IP fields, i get IP addresses of remote hosts!.
I would like to ask you about ASA 5510 (Active/Standby). i have two ASA 5510 and i did configuretion failover and it is working ( Active / Standby) but my issue that when primary donw, the standby unit up to primary but the primary came back the standby unit it not switch to standby ( i mean it still up ) . if i want to primary up i type command ( failover active ) on primary unit , so i don't want use manul command i want it auto.Which command that make ASA failover when primary coma back? [code]
i read that you need only one L-ASA5510-SEC-PL for setting up a Active/Standby Failover. I installed the license on the 1st ASA and tried to setup the failover via the ASDM wizard. It always fails, because the 2nd device can't have a 'base' license.So does this mean, i really need another license?
I currently have a LAN-based failover setup between two 5510s. The failover link is a crossover cable. In the current setup, if I unplug the crossover cable both units become active. From what I understood from Cisco documentation, each unit should mark the failover interface as down and there shouldn't be any failover. That's exactly how I want this setup to work.
I have just finished setting up two ASA5510s in Active/Standby Staeful failover, using the Management interface for both failover and state. Everything appears to be working well.Configurations were transferred and the "sh failover" on both accurately reports their status before and after a failing the active device.I monitored the inside IP with a continuous ping (using a Windows client) and noticed that there were usually two to three ping responses lost. Is this normal?
I am looking to add the IPS module to my ASA 5510's. I am contemplating only purchasing one module and placing it in the active ASA. I am willing to accept that in a failure scenario I will loose the IPS functionality until the primary ASA is recovered. I have not had a chance to talk to my SE to see if this is even possible. Has anyone attempted a deployment such as this? Will it work and is it supported?
I have 2 FWSM running on 2 Cat6500 chassis, they work as a Active/Stanby group. Firewall mode is transparent. [code] HA is running well, but I can not ping the standby IP (10.98.1.248). So what could be the problem?
Can I upgrade Active/standby pair from 7.2(4) to 8.0(5)25 directly or need to upgrade to 8.0.2/4 first? Upgrade an Active/Standby Failover ConfigurationComplete these steps in order to upgrade two units in an Active/Standby failover configuration:Download the new software to both units, and specify the new image to load with the boot system command.Refer to Upgrade a Software Image and ASDM Image using CLI for more information.Reload the standby unit to boot the new image by entering the failover reload-standby command on the active unit as shown below:active#failover reload-standbyWhen the standby unit has finished reloading and is in the Standby Ready state, force the active unit to fail over to the standby unit by entering the no failover active command on the active unit.active#no failover activeNote: Use the show failover command in order to verify that the standby unit is in the Standby Ready state.Reload the former active unit (now the new standby unit) by entering the reload command:newstandby#reloadWhen the new standby unit has finished reloading and is in the Standby Ready state, return the original active unit to active status by entering the failover active command:newstandby#failover activeThis completes the process of upgrading an Active/Standby Failover pair.
Is the preempt option available in active standby ASA firewall setup with single context...somewhere i have read that same is available in active-active setup or active/standby setup with multiple context.If i active the multiple context mode on product environnement with two ASA5520 in Active/Standby mode, what are the impacts on the the production?
1. We have Two 3900 Router on the core layer which are terminated with one ISP on one Router and Secondary ISP on Second Router.
2. Can we configure my ASA 5520 with Active/Standby termenating two IPS providers one on Active ASA 5520 and Other ISP on Standby ASA 5520, so that when Active ISP fail ASA Secondary can become Active and send the Traffic throough Secandary ISP.
3. The reasion behind giveing Public IP on Firewall is to Terminate VPN on our Firewall i.e. SSL and IPSEC VPN.
Few Clarification If we can achive the above:
1. How will the DMZ Servicec nated with my Primary ISP on my Primary ASA will be routed when the Secondary ASA is acting as Active Firewall.
2. Can Web SSL and Client To Site IPSEC VPN users access service via the Secondary ISP- ASA when my Primary ASA and ISP is down.
I currently have two 5540's in an Active/Standby pair. The primary unit failed on February 12th, so the secondary ASA is now the active one. My question is this - we have made a lot of changes since February 12th and I am planning on fixing this failover issue over the weekend. Will the secondary (now active) FW sync it's config to the non-active FW, or will the failed FW sync it's out-of-date config - removing any changes that we've made in the last month or so.
I have two ASA5510 configured in an active/standby failover configuration. Everything is working well, but I would like to remove DMZ2 as it is no longer needed. On my DMZ2 interface, I have removed the security level and the IP address and shutdown the interface. However, when I do a "show failover" DMZ2 is still showing up. I would like to remove it completely so that failover isn't even "monitoring" this interface. What command am I missing or what do I need to do to completely remove this interface from this "show failover" listing? [code]
I am getting ready to setup avtice/standby failover on our ASA 5520's and have run in to an issue.I currently only have one External IP address available. My Idea was to use a private/placeholder IP address for the standby external IP Address, will this cause any issues with the failover? I know I won't be able to access the secondary from the outside, but that is not an issue.
I have been asked to look at upgrading two 5520 ASA configured in a HA pair Active/Standby, from version 7.2(4) to version 8.3(1) to bring it in line with some other ASA firewalls in the organisation.
My question is can I simply upgrade straight from 7.2(4) to 8.3(1) or will I have to step the upgrade from 7.2(4) => 8.2(x) => 8.3(1)
Having read a few articles on the forums and the release notes I think I should be able to go from 7.2(4) => 8.3(1) .
The second part of my query is around the upgrade itself, having researched this a little there seems to be various views on how to go about upgrading a HA pair and I cannot find anything specific on the website.
The approach I am thinking of is simply as follows;
- upload images onto both firewalls in the HA pair - On the standby from the CLI clear configure boot
I have a dual ISP, 1 primary and 1 secondary terminated on fa0 and fa2 on our ASA respectively. ASA was configured so that, when the primary fails, the secondary kicks in. [code]
It was until yesterday that we experienced downtime on the primary ISP that the secondary doesn't do the fail-over. I have to manually configure the device to use the secondary ISP. Currently, I'm looking at maybe this has something to do with the licensing.We are currently using a Base License, should we be upgrading to Security Plus?
We are planning to install a new SSM-4GE module on both Active and Standby firewalls. how can we install an new SSM-4GE with a minimum outage. I was planning to install the module in the following steps.
1. Power off the secondary firewall(FW02). 2. Install a new module. 3. Power up the secondary firewall 4. Power off the primary firewall(FW01)---> in this step will the secondat firewall become active as there is a hardware conflict. 5. Install a new module. 6. Power up the Primary firewall(FW01)
or do i need to power down both the firewalls and then install the modules?i have is that after the installation only one port on the new SSM-4GE module would be in use on Primary firewall(FW01) which is a terminating link from a router. No link would be terminating on the new SSM-4GE module on secondary firewall. Will the firewalls still fail over in this case or does it require a link going to the secondary firewall on new SSM-4GE module(same port as on primary firewall) from the router.
I need to configure multiple context mode with active/standby failover solution.
Even after reading some Cisco documents I still can't understand if active/standby failover configuration has to be done within the admin context only or also within every single context (context-1, context-2 for example). In this case I have to allocate as failover interface a subinterface for each context (admin, context-1, context-2), right ?
Therefore a I have an other question: within the admin context, in a failover solution, do I have to allocate all interfaces I want to be moniotred, even though some will be used by context-1 only context and some others will be used by context-2 only context ?
An other question is: if active/standby failover configuration has to be done within each context, can I set regular failover within context-1 while stateful failover within context-2 ?
The last question is: can I use management interface within all 3 contexts ?
I have 2 ASA 5540s ver 8.3 in Active/Standby state.I am considering a future hypothetical situation where I might need to rename interfaces or reallocate redundant interface groups. Doing so obviously has a major impact on the current primary configuration. My goal would be to minimize or eliminate network downtime during the interface changes.
I am wondering if it is possible to force the secondary ASA from the standby to active state.Then temporarily disable failover on the primary unit.Make the interface changes on the primary unit Then reactivate failover on the primary unit Force the primary unit back to active and secondary unit to standby My new interface configuration would then sync from the primary to the secondary.
I believe this would work but must ensure that the secondary ASA can function as the active unit while the failover is disabled on the primary unit. Is there a set length of time the secondary unit can remain active without a failover peer?
see issues with operating the secondary unit in this manner while making changes to the primary unit?
I have a 5510 ASA and have been given another an told to make them active and standby. Basically the active one is working great but the second one has no config on it apart from the default one, but is the same firmware level. I guess I need a crossover cable, and what happens with the inside and outside interfaces, would they need to go into a vlan on a switch, one inside vlan where the 2 firewalls inside interface go into and another vlan for the outside? Otherwise if it failsover to the standby ASA the inside and outside interfaces wouldn't work.
I just added a new 5510 failover unit to an existing 5510 and when connecting my new outside interface on an Active/Standby firewall pair, i get errors messages (red x) on each port scan (monitor & syslog) although the error message indicate all ports are good...additionally the firewalls flip between active and standby non stop. I remove the new standby unit outside interface from a shared switch and everything clears up.