i do have two 6500 in VSS mode , and one FWSM module on each 6500, i want to configure these modules as Active/Standby, how do i start , should i follow this (not in VSS mode): url..
View 1 RepliesI have 2 FWSM running on 2 Cat6500 chassis, they work as a Active/Stanby group. Firewall mode is transparent. [code] HA is running well, but I can not ping the standby IP (10.98.1.248). So what could be the problem?
View 3 Replies View RelatedI have been having an annoying issue for the past few weeks with my ASA setup. We are using the ASA as our Remote Access Gateway and originally had it setup in a Active/Standby failover configuration using 2 x 5520 ASA's.The original setup of the devices was that the 2 x ASA were setup in a failover configuration, with both of them connecting back to the internal network via a 6500 device. Because of using failover I created a VLAN on the 6500 and put the two ports that connect the ASA's into that VLAN. I then configured the VLAN interface to be the EIGRP interface for the neighbour relationship to the ASA's.
The problem I am seeing is that the EIGRP neighbour relationship between the Active ASA and the 6500 keeps flapping. It occurs abour 4-5 times every day at randmon intervals. Sometimes the neighbour relationship will stay up for 6-7 hours, other times it flaps every 1-2 hours. I initially thought it was due to the failover configuration so I removed one of the ASA's and removed all of the failover configuration, but the EIGRP neighbour flapping problem still exisits. [code] Since removing the failvoer configuration I am thinking it could be a physical cable problem?
I need to setup an ASA 5525 in Active/Standby failover mode. I am setting up the ASA for a company that purchased only one public IP address. The public IP address is assigned to the outside interface. My question is will failover work correctly if I don't use a secondary IP address on the failover configuration on the outside interface?
View 4 Replies View RelatedWe have currently install single ASA 5550 and want to install one more ASA for active standby mode, but cisco discontinue or End of sale ASA 5550. can any one guide me ASA 5555X is compatible with ASA5550 on active standby mode or not.
View 2 Replies View RelatedWe configuring ASA 8.4.2 in Active/Standby failover mode with two cables. What would be the best design configuring etherchannel on ASAs or have one active and one standby redundant cable ?
View 1 Replies View RelatedI am a single ASA-5510 with CSC module.I want to pair it for active/standby mode for failover .... can it be done if second ASA doesn't have the module? Can I assume the in case of a failover, the traffic won't be checked, and primary does in case CSC module fails?
View 2 Replies View RelatedI have 2 modules of FWSM in 6500 switch (failover). I need 5 context. When I use in routed mode (like in the picture) , I cannot ping the servers behind the firewall. (I have ping to FW context) In transparent mode, it is not happening.
View 1 Replies View RelatedI have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies View RelatedI have a pair of ASA 5520s operating in failover pair as active/standby, having two contexts on them. I am planning to share the load and make it active/active making first context active on the primary unit and second context active on the secondary unit. My question is if this will disrupt any connectivity thru these firewalls when I do "no failover" on the active/standby and assign the contexts to different failover groups and enable the failover back.
View 6 Replies View RelatedWe have a setup of FWSMs configured in single mode in 6509 chassis. Both 6509 are configured in VSS. Recently I have upgraded the firmwre from 4.0(3) to 4.1(3).....before upgradation config sync was not having any problem.
After upgradation...If any one of the FWSM reload..while coming up it gets stuck in config sync and no command we can run on any of the unit and get the error as..
Configuration update in progress by another process. Also on stannby fwsm no running-config displays.
If we used # failover suspend-config on primary and then reloads the standby fwsm...standby boots up with startup config and when # no failover suspend-config command runs on active fwsm..the sync started and completing succssfully within 15 sec..
Also failover works well..with #no failover active..
I have two ASA 5510s running in Active/Active mode. I need to make config changes on them. How do I go about it? Do I power off the secondary ASA and make the config changes on the primary and then power on the secondary ASA ? Or this another way to do this?
View 3 Replies View RelatedHow I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
I would like to work with two ASA's 5550 in HA (Acitve-Standby) like perimetral firewalls and also work with another ASA 5540 but like a SSL VPN Remote Access to end users.Which will be the best topology to this scenary?. Perhaps i need to put the ASA 5540 SSL VPN together with the ASA's in HA directly in a port.
View 1 Replies View Relatedi have 2 ASA 5505 running 8.3(1) and ASDM 6.3(1).
the first unit is currently working, and i now wish to configure the second unit as standby. im configuring through the ASDM GUI. Started the HA Wizard, choose Active/Standby configuration and enter the IP of the peer device. checks come back all ok. On the LAN link configuration page (step 3of6) Interface is pre selected as VLAN99, I give it a logical name as iface_fail, and enter 10.0.0.1 as primary address and 10.0.0.2 as standby, subnet as 255.255.255.248, and select port Ethernet0/5
Note that if i click on the buttons next to the IP fields, i get IP addresses of remote hosts!.
I have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.interface GigabitEthernet3/0description LAN/STATE Failover Interfacespeed nonegotiate.
View 5 Replies View RelatedI would like to ask you about ASA 5510 (Active/Standby). i have two ASA 5510 and i did configuretion failover and it is working ( Active / Standby) but my issue that when primary donw, the standby unit up to primary but the primary came back the standby unit it not switch to standby ( i mean it still up ) . if i want to primary up i type command ( failover active ) on primary unit , so i don't want use manul command i want it auto.Which command that make ASA failover when primary coma back? [code]
View 2 Replies View Relatedi read that you need only one L-ASA5510-SEC-PL for setting up a Active/Standby Failover. I installed the license on the 1st ASA and tried to setup the failover via the ASDM wizard. It always fails, because the 2nd device can't have a 'base' license.So does this mean, i really need another license?
View 5 Replies View RelatedI have two ASA 5520 version 8.2 in active Standay Mode. What is a good practice to setup IPS AIM ssm-20 for this setup.
Is IPS should be in Fail-Open or Fail-Close mode ?
Is Mangement ip for both IPS module should be same or diffrent. ?
I currently have a LAN-based failover setup between two 5510s. The failover link is a crossover cable. In the current setup, if I unplug the crossover cable both units become active. From what I understood from Cisco documentation, each unit should mark the failover interface as down and there shouldn't be any failover. That's exactly how I want this setup to work.
View 5 Replies View RelatedI have just finished setting up two ASA5510s in Active/Standby Staeful failover, using the Management interface for both failover and state. Everything appears to be working well.Configurations were transferred and the "sh failover" on both accurately reports their status before and after a failing the active device.I monitored the inside IP with a continuous ping (using a Windows client) and noticed that there were usually two to three ping responses lost. Is this normal?
View 1 Replies View RelatedI have two 5505 ASA. I would like to know can I make two 5505 failover redundant with active standby setup?
View 11 Replies View RelatedI am looking to add the IPS module to my ASA 5510's. I am contemplating only purchasing one module and placing it in the active ASA. I am willing to accept that in a failure scenario I will loose the IPS functionality until the primary ASA is recovered. I have not had a chance to talk to my SE to see if this is even possible. Has anyone attempted a deployment such as this? Will it work and is it supported?
View 3 Replies View RelatedWe have 2 ASA 5505s in a data center at a remote site.
Whilst troubleshooting another issue I noticed the below. I don't know much about fail over but this would suggest that the secondary ASA is active and the primary ASA is on standby.
if the primary is "active" then how come the secondary is the active ASA? I would have thought that once the primary ASA became active this would assume the "main" role".
[Code] .....
I am in the process of adding a new ASA 5550 as a standby box to an existing ASA 5550 running on transparent mode. Both are on version ASA 8.0(4) and ASDM 6.2(1). I have set the new ASA 5550 to transparent mode. The configurations are the following for the HA: [code]My questions are the following:
1. The management ip address is different than the ip used for the failover link. Since the firewalls are on transparent mode, does the failover ip needs to be the same as the management ip address?
2. Does any other additional config is needed for HA to work for basic active/stand-by failover?
3. Which is the best method to add the second box without disrupting the active box?
Can I upgrade Active/standby pair from 7.2(4) to 8.0(5)25 directly or need to upgrade to 8.0.2/4 first? Upgrade an Active/Standby Failover ConfigurationComplete these steps in order to upgrade two units in an Active/Standby failover configuration:Download the new software to both units, and specify the new image to load with the boot system command.Refer to Upgrade a Software Image and ASDM Image using CLI for more information.Reload the standby unit to boot the new image by entering the failover reload-standby command on the active unit as shown below:active#failover reload-standbyWhen the standby unit has finished reloading and is in the Standby Ready state, force the active unit to fail over to the standby unit by entering the no failover active command on the active unit.active#no failover activeNote: Use the show failover command in order to verify that the standby unit is in the Standby Ready state.Reload the former active unit (now the new standby unit) by entering the reload command:newstandby#reloadWhen the new standby unit has finished reloading and is in the Standby Ready state, return the original active unit to active status by entering the failover active command:newstandby#failover activeThis completes the process of upgrading an Active/Standby Failover pair.
View 10 Replies View RelatedIs the preempt option available in active standby ASA firewall setup with single context...somewhere i have read that same is available in active-active setup or active/standby setup with multiple context.If i active the multiple context mode on product environnement with two ASA5520 in Active/Standby mode, what are the impacts on the the production?
View 1 Replies View Related1. We have Two 3900 Router on the core layer which are terminated with one ISP on one Router and Secondary ISP on Second Router.
2. Can we configure my ASA 5520 with Active/Standby termenating two IPS providers one on Active ASA 5520 and Other ISP on Standby ASA 5520, so that when Active ISP fail ASA Secondary can become Active and send the Traffic throough Secandary ISP.
3. The reasion behind giveing Public IP on Firewall is to Terminate VPN on our Firewall i.e. SSL and IPSEC VPN.
Few Clarification If we can achive the above:
1. How will the DMZ Servicec nated with my Primary ISP on my Primary ASA will be routed when the Secondary ASA is acting as Active Firewall.
2. Can Web SSL and Client To Site IPSEC VPN users access service via the Secondary ISP- ASA when my Primary ASA and ISP is down.
I currently have two 5540's in an Active/Standby pair. The primary unit failed on February 12th, so the secondary ASA is now the active one. My question is this - we have made a lot of changes since February 12th and I am planning on fixing this failover issue over the weekend. Will the secondary (now active) FW sync it's config to the non-active FW, or will the failed FW sync it's out-of-date config - removing any changes that we've made in the last month or so.
View 1 Replies View RelatedI have two ASA5510 configured in an active/standby failover configuration. Everything is working well, but I would like to remove DMZ2 as it is no longer needed. On my DMZ2 interface, I have removed the security level and the IP address and shutdown the interface. However, when I do a "show failover" DMZ2 is still showing up. I would like to remove it completely so that failover isn't even "monitoring" this interface. What command am I missing or what do I need to do to completely remove this interface from this "show failover" listing? [code]
View 7 Replies View RelatedI am getting ready to setup avtice/standby failover on our ASA 5520's and have run in to an issue.I currently only have one External IP address available. My Idea was to use a private/placeholder IP address for the standby external IP Address, will this cause any issues with the failover? I know I won't be able to access the secondary from the outside, but that is not an issue.
View 2 Replies View RelatedI have been asked to look at upgrading two 5520 ASA configured in a HA pair Active/Standby, from version 7.2(4) to version 8.3(1) to bring it in line with some other ASA firewalls in the organisation.
My question is can I simply upgrade straight from 7.2(4) to 8.3(1) or will I have to step the upgrade from 7.2(4) => 8.2(x) => 8.3(1)
Having read a few articles on the forums and the release notes I think I should be able to go from 7.2(4) => 8.3(1) .
The second part of my query is around the upgrade itself, having researched this a little there seems to be various views on how to go about upgrading a HA pair and I cannot find anything specific on the website.
The approach I am thinking of is simply as follows;
- upload images onto both firewalls in the HA pair
- On the standby from the CLI
clear configure boot
[Code].....
I have a dual ISP, 1 primary and 1 secondary terminated on fa0 and fa2 on our ASA respectively. ASA was configured so that, when the primary fails, the secondary kicks in. [code]
It was until yesterday that we experienced downtime on the primary ISP that the secondary doesn't do the fail-over. I have to manually configure the device to use the secondary ISP. Currently, I'm looking at maybe this has something to do with the licensing.We are currently using a Base License, should we be upgrading to Security Plus?