Cisco Firewall :: 6509 - Standby FWSM Stuck In Sync After Reload
May 8, 2011
We have a setup of FWSMs configured in single mode in 6509 chassis. Both 6509 are configured in VSS. Recently I have upgraded the firmwre from 4.0(3) to 4.1(3).....before upgradation config sync was not having any problem.
After upgradation...If any one of the FWSM reload..while coming up it gets stuck in config sync and no command we can run on any of the unit and get the error as..
Configuration update in progress by another process. Also on stannby fwsm no running-config displays.
If we used # failover suspend-config on primary and then reloads the standby fwsm...standby boots up with startup config and when # no failover suspend-config command runs on active fwsm..the sync started and completing succssfully within 15 sec..
Also failover works well..with #no failover active..
View 3 Replies
ADVERTISEMENT
Sep 30, 2012
I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.
View 1 Replies
View Related
Jul 24, 2011
I have 2 FWSM running on 2 Cat6500 chassis, they work as a Active/Stanby group. Firewall mode is transparent. [code] HA is running well, but I can not ping the standby IP (10.98.1.248). So what could be the problem?
View 3 Replies
View Related
May 10, 2012
i do have two 6500 in VSS mode , and one FWSM module on each 6500, i want to configure these modules as Active/Standby, how do i start , should i follow this (not in VSS mode): url..
View 1 Replies
View Related
Oct 29, 2012
our FWSM (in 6509) is not coming up, when tried to sesssion up using "Session slot 1 proc 1" command,It is giving error , "Tyring 127.0.0.11 .....connection timed out remote host not responding".
In "show mod" command output at Switch in IOS console: under Card Type Section: it is showing Model & Serial Number correctly, Under MAC address sectino: displaying some MAC address But in Online Diag Status, it showing "Unknown" for Module 1.
We tried re-seating in other slots, but of no use. Giving same error. Some of other forms are saying it is the issue with 128 Mb CF image problem, FWSM is no more reachable from 6509 IOS console. We even tried using FWSM console (using PC-Conse & LCP Console) but FWSM is not contactable.
View 1 Replies
View Related
Jul 16, 2011
I think I got a strange behavior on a context of my WS-SVC-FWM-1 (on a Catalyst 6509 running IOS 12.2(18)SXF17a) that is running FWSM Firewall Version 4.1(3). This context sends these log messages every ten minutes:
Jul 17 2011 23:31:16: %FWSM-6-302010: 0 in use, 0 most used
Jul 17 2011 23:31:17: %FWSM-6-302010: 2245 in use, 107133 most used
[code]...
If I issue the "show conn" three seconds later the log message, the output I got is: FWSM# sh conn 1041 in use, 107133 most used
In another context on the same FWSM the log message sent every ten minutes is just this one:
Jul 17 2011 23:31:17: %FWSM-6-302010: 1358 in use, 72503 most used
Jul 17 2011 23:41:22: %FWSM-6-302010: 1590 in use, 72503 most used
In this case there is no the log message where the "in use" field and "most used" field are 0 (zero). why does the context send the message with the "in use" field and "most used" field 0 (zero).
View 1 Replies
View Related
May 17, 2011
I have attached a drawing of our network. We have two 6509's connected to two Cisco 2811 (onsite) that the ISP owns. I am trying to get one side up and running before I worry about redundancy and so forth. For this reason I have set all the HSRP priorities to 110 on the left 6509. I have HSRP running between the ISP routers and V LAN 101 of the 6509's. This works as I can ping yahoo and Google just fine from the 6509 switch. I can't get from my laptop connected to V LAN 23 to the internet.
It doesn't even attempt to NAT as there are no translations. I have public address assigned by my ISP configured between the ISP routers and my 6509 on V LAN 101. I then have the public address assigned to V LAN 100. I configured V LAN 100 on the switch and V LAN 100 on the FWSM with the IP address in the drawing. I have my NAT statements and route in my FWSM according to the drawing as well. On the switch, I have a default route to X.X.12.19 which is the VIP between the ISP routers. I can reach anything on the inside of my network, including the old network addresses from V LAN 23.
1. Is it best to do NAT at the FWSM or should I do it on the MSFC connected to the ISP routers?
2. If I have to configure NAT at the FWSM, does this requires me to extend the public network down to the FWSM?
3. I'll take any examples you may have as I am stuck.
View 2 Replies
View Related
May 8, 2011
I have successfully completed HSRP and failover configuration.When both switch are runnign then the failover run successful and wheneber one link fail then the failover run successfully but when down one 6509(total box) the failover not working.....
View 7 Replies
View Related
Oct 19, 2011
I am having issues trying to track down what is causing a high number of connection on our FWSM in our core 6509 switch. I recently upgraded my FWSM to 3.1(20) and I'm looking for a tool to be able to find the culprit. When I receive these messages I try to get onto the firewall in time to be able to get information regarding this issue but by the time I do the device recovers. Is there a way to tweat the threshold of the SNMP trap for high connections? Is there any way I can retreive this information via SNMP? Is there are command that will allow me to extract the local IP making the most connections?
View 1 Replies
View Related
Jun 9, 2013
I happen to noticed the FWSM was dropping packets at about 387 packets every 5 minutes. My outside FWSM is WAN facing and has a 1gig link (35% utilized) my inside facing has about 100 downstream switches to the closets. I do not see my 6509's back plane is being over utilized and my understanding of the FWSM show be go for 5 gig so it isn't oversubscribe. Why i am seeing packets dropped?
[Code] ......
View 2 Replies
View Related
Jul 2, 2011
I have attached a pdf of an example of a FWSM configuration with shared interfaces. Now what I dont get is (please refer to the link) url...Is there any difference between the natting that they have done on page B-4 on Context A.as opposed to configuring a static NAT for processing traffic to correct context nat(inside,outside) 209.165.201.0 10.1.2.0.The other question is on page B-2 (diagram) Context A has a customer A network linked to the inside interface. Is it possible to put a default route towards that "Network 2" cloud and restrict traffic from the 6509 switch towards the context A?
View 5 Replies
View Related
Oct 4, 2011
I have problem with traffic coming from GRE interface and going further through FWSM on the same 6509-E chassis.It's very interesting and confusing. If packets are fragmented, I can go through, however, if I use normal packets (usual ping for example) traffic goes from outside to inside and stops on it's way back.
Here is the detailed info:
WS-C6509-E with WS-SUP720-3B
FWSM HW 4.0, SW 4.1(4)
GRE is done in hardware (source is loopback interface - only one loopback per GRE tunnel).
View 5 Replies
View Related
Jan 8, 2012
i have 6509+FWSM(4.0.4) now i wanna use stite to stite and ez vpn in the fwsm (multiple context) multiple context mode in fwsm support ipsec vpn?
View 2 Replies
View Related
May 29, 2012
Does the FWSM for a 6506/6509 is supported in a VSS environment?Also, does the FWSM work with the 2T supervisor module?
View 1 Replies
View Related
Mar 6, 2011
I need to enable Management access to FWSM using CA ssl certificate.
FWSM Version 3.2(5) in Cisco 6509 switch.
Got to know how to generate, import and export certificate but my query is how to get it applied to the management ip do i need to apply in the management interface.
View 1 Replies
View Related
Nov 4, 2012
We are in the process of migrating to the ASA service modules on both our 6509E switches from our current FWSM. We have used the Cisco conversion tool and applied that to the service module. When viewing the context in ASDM we are unable to view the object names in the right hand pane.
On the FWSM I would see the following under Network Objects:
Network Objects
- JQ-Test
- JQ-Test2
- JQ-Test3
Network Object Group
+ JQ Group
- JQ-Test
- JQ-Test2
- JQ-Test3
Now I have run the conversion tool and applied that to the ASA's I now get the following results.
Network Objects
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
Network Object Group
+ JQ Group
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
I am aware that the naming convention on the ASA's are different to the FWSM as you can no longer use the "name 1.1.1.1 JQ-Test1" format but I was hoping that the conversion tool would do this for me.
Is there any way I can get the names of the object back without having to script something that takes the old FWSM format and convert it into an ASA format?
View 1 Replies
View Related
Oct 27, 2011
Currently we have two inter-chassis FWSM redundancy. I would like to configure them for intra-chassis.
Both FWSM's are in slot 7 of 6509 switches and i want to take secondary out from one of the 6509 switch and insert in the slot 3 of primary switch.
I addedd the following commands in my primary switch.
There were commands already present for FWSM in primary switch
firewall multiple-vlan-interfaces
firewall module 7 vlan-group 1
firewall vlan-group 1 2,3,777
to create intra-chassis redundancy i addedd the following command also there.
firewall module 3 vlan-group 1
after adding that, my firewalls worked fine but there was a issue with site loading. People from outside were able to access inside but from inside, we were not able to go outside.
do we need to clear arp from both FWSM's ? is there any other precautionary step, which we need to follow while working on it.
View 1 Replies
View Related
Apr 15, 2013
We have a faulty FWSM module in Cisco 6509 switch in Active/Standby cluster mode
We have purchased a refurbished FWSM module to replace it. It has the same FWSM OS 4.0 (4) and is in factory default configuration
What procedures should I follow to make this unit live and sync the config between the current active unit to this one.
View 1 Replies
View Related
Aug 8, 2012
i have been facing strange issue on FWSM (6509 switch). we have created a vlan inteface for server farm on fwsm and its stop responding automatically and we need to give shut/ no shut command under that interface to back into normal .
View 11 Replies
View Related
May 9, 2011
I have FSWM active/standby installed in 6509-E core switches running following FWSM Firewall Version 3.1(3) Device Manager Version 5.0(2)F..I want to upgrade to latest FWSM version as well as ASDM, I downloaded asdm-622f.bin and c6svc-fwm-k9.4-1-5.bin from cisco portal. When i checked the show version of FWSM, it says..The Running Activation Key is not valid, using default settings: Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000
I have gone through threads on CSC about how to upgrade FWSM in failover mode, now my concern is, Do i have to take care about activation key or keep as it is ? I have maintenance contract with cisco for all devices.
View 3 Replies
View Related
Oct 20, 2009
I have two ACE-4710 in active/standby mode, running code A3(2.2). Four contexts are configured. Both devices were functional without problem, until I reload the standby unit. After reload, the standby unit completely lost its configuration with exception of the FT vlan and the FT peer configuration in the Admin context... Both units recognized each-other and I can still ping the primary unit on the FT vlan, but nothing else. Contexts are lost and interfaces are shutdown! Nothing changed at the software level, both devices run exactly the same image and the same licences are installed (it worked well before the reload).
So, I decided to reconfigure the basics on the standby unit in order to trigger a config sync from the primary. And here arrives the problem : I reconfigure the FT vlan, the FT peer, I check the peer state and everything is OK.
Then, I try to ping the primary unit from the standby unit with success :
switch/Admin# ping 192.168.16.1
Pinging 192.168.16.1 with timeout = 2, count = 5, size = 100 ....
Response from 192.168.16.1 : seq 1 time 0.000 ms
[Code]......
View 3 Replies
View Related
Dec 26, 2012
When i have configured the 4507R switch but the configure is not sync with the standby module..... I have doing some troubleshooting
1. type the command "show redundancy" no standby module is showing
2. type the command " redundancy force-switchover" showing the message " no standby module is present"
3. type the command "hw-module module 2 reset" then the standby module is reset and status light is blinking like it is booting..
View 6 Replies
View Related
Aug 12, 2012
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
View 1 Replies
View Related
Oct 29, 2012
After a power outage our standby VSS switch has not recovered. The switch keeps cycling through its initialization and then powers off all modules.
The Dead peer detection is working and VSL links are up.
View 6 Replies
View Related
Jan 1, 2012
We had an power shutdown activity last week, due to which one of the core switch was turned off and ON .After the core switch was turned ON, we had found some of the ACLs missing which were bounded in VLANs. We had given write command before this power shutdown activity.We need to find the root cause for the same.
Switch Model-WS-CISCO-6509-E.
View 3 Replies
View Related
Mar 9, 2013
We have a backup sup 720 which has a 2 gigabit ethernet though port channel, to another chassis. Suddenly UDLD detected an error and got into err disable, then this err disable didn't let the interface set to DOWN, and created a switch loop, then our Supervisor reloaded. I'd like to know what could have caused this reload. In my opinion could have a been the switch loop, but also I've been checking from the output interpreter the show tech and might have been a bug, the only one that could match in IOS version 12.2(33)SXH, is this one: url...
We're going to disable err-disable next time I guess and recover the link manually, apart from that what could have made the sup for crash and reload?
View 4 Replies
View Related
Jul 31, 2012
Suffered a big outage on the network, the fix was to reload the module 3 on the 6509 switch, we had these errors on the log %CONST_DIAG-SW1_SP-3-HM_PORT_TEST_FAIL: Switch 1 Module 3 TestUnusedPortLoopback Port(s)[24,46] failed. System operation continues.in the end, we reloaded the card and it was all ok. is there anything I can do to check the card / or any deeper logs? would that error cause the card to crash?
View 1 Replies
View Related
Sep 22, 2011
last night I started upgrading our ASA5520 active/standby cluster. Because of lack of memory, I stopped the upgrade process and will continue when the memory modules have arrived... Currently I'm running 8.0(5) on both nodes (Version: Ours 8.0(5), Mate 8.0(5))Whenever I use the "write standby" command on the active ASA, the passive ASA seems to drop it links for a short while. [code]
View 4 Replies
View Related
Aug 8, 2012
i am feeling an issue related to 2 x 6509 with fwsm.
Mod Ports Card Type Model --- ----- -------------------------------------- ------------------ ----------- 1 6 Firewall Module WS-SVC-FWM-1 2 48 CEF720 48 port 1000mb SFP WS-X6748-SFP 3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX 4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX 5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G
Hw Fw Sw Status ------------ ------------ ------- 4.3 7.2(1) 4.1(2) Ok 1.12 12.2(14r)S5 12.2(33)SXH3 Ok 3.0 12.2(18r)S1 12.2(33)SXH3 Ok 3.0 12.2(18r)S1 12.2(33)SXH3 Ok 2.1 8.5(2) 12.2(33)SXH3 Ok
on fwsm we have different dmz for different application. mostly of Oracle (1521 port) to application means seperate one. problem is oracle people reported the slow performace when exporting dump from once vlan to another. before that they are using 3com technology (network) and on this its ok. time difference is double from old to new.
i had sniffed the traffic also and found alot of TCP OUT OF ORDERS errors. i read that this is the bug which is resolved in 4.0.
View 10 Replies
View Related
Dec 16, 2012
I have 6509 E. Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.
View 11 Replies
View Related
Nov 17, 2012
I have a vlan defined in FWSM for server farm there is a one server with two IP addresses and teaming has done on it how ever from FWSM i am able to ping both IP addresses but from core 6509 switch i am only able to ping one ip address. from FWSM show ARP command displays the same virtual mac addresses against both IPS of the same server.
View 2 Replies
View Related
Oct 8, 2012
We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
1. Is above correct? Will my line card reload?
2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?
View 1 Replies
View Related
Feb 7, 2012
Configuring FWSM in a 6509. When I set "firewall vlan-group 40 40-42,251", it results in: "No more than one svi is allowed. Command rejected.".
I had "firewall multiple-vlan-interfaces" set for a previous use of this module, but took that off with the "no" command. Suspect that is the issue, but do not see how to resolve. Seems similar to bug CSCsr48563, but I am at the fixed code for that bug.
View 1 Replies
View Related
