Cisco WAN :: No Duplex Auto On 7604 Router
Oct 18, 2011
I have a 7604 Edge router that connects to our Data centre via Fiber.
but i keep getting input errors on the interface Gi3/5. i also found out that i cannot change the duplex settings on the edge router to auto, i only have two options of full and half and changing it has not worked either.
I have tried to use a switch in between the fiber modem and the edge router to try to manipulate the duplex settings, but when i tried it the port simply shutdown and then i have to reverse the configuration.
The software version of the router is 12.2(33)SRE3, i really need to sort this out as connection to and from the Data centre is quite slow.
View 3 Replies
ADVERTISEMENT
Jun 11, 2012
We are facing to an annoying issue. We have a 6509 running in Catos 8.3(4) with WS-X6548-GE-TX, WS-X6348-RJ-45 and WS-X6148-RJ-45. When we configure the mode in auto negotiation, it comes up in half duplex. We need to configure the speed mode at 100Mbit/Full to make it work. But if the chassis or port restarts (not the server), the link becomes half duplex. This happens only on module in Gigabyte like WS-X6548-GE-TX.
Cable have been replaced but does not work. It is not happened on another chassis running on IOS 12.2(18)SXF17b with WS-X6548-GE-TX.
View 4 Replies
View Related
Jul 30, 2012
I have tried to reset the password for 7604 but it is not working. At the rommon mode, i input 0x2142, and then reset.
It reloads and keeps asking for password.
View 7 Replies
View Related
Apr 13, 2013
I have autonegotiation disable on my interfcae what should be duplex setting on other end?
Router#sh run int Gi0/3/0
Building configuration...
Current configuration : 334 bytes(code)
View 4 Replies
View Related
May 3, 2012
I have a video conferencing device and I struggled a lot with a bunch of different routers. I was giving up but then I plugged in a friend's old Linksys/Cisco Adsl gateway and all the problems disappeared (kudos to Cisco). The problem is that the gateway is not ADSL2+. I have since borrowed a Linksys/Cisco ADSL2+ router, however, there isn't a possibility to enter port speeds/duplex manually (required to prevent packet loss in video conferencing, I really want to have that option for the peace of mind). I have been looking around on the internet but I can't seem to find this ability any routers' specs. What I need is as follows:
- Has to be Cisco or Linksys router
- Has to be ADSL2+ (Annex A)
- Doesn't have to be wireless, even single port is OK
- Preferably has DMZ
- Ability to hard code lan port speed/duplex (i.e. no autosense)
- No other functions needed so hopefully a cheap option
View 17 Replies
View Related
May 24, 2012
I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies
View Related
Jun 27, 2011
To establish s secure tunnel using GRE with IPSec do I need to add a SPA-IPSEC module to my 7604 chassis?
View 1 Replies
View Related
Aug 31, 2011
I want to implement QoS on our Core router but the core router makes use of GRE Tunnels to remote branch locations.so far all QoS techniques i want to use cannot be implemented using tunnel interfaces.
the core router is a cisco 7604 router with IOS version 12.2 (33)SRE while the remote locations have ISRs (2821).
Which QoS technique to use with respect to GRE Tunnels as there are times of congestion due to heavy network traffic to those remote locations.
View 16 Replies
View Related
Jul 15, 2012
We have a 7604 chassis with the following equipments:
1. RSP720-3C-10GE
2. 7600-SIP-400
3. SPA-1X10GE-L-V2
We would like our SPA to support XFP transceiver having part number XFP-10GZR-OC192LR.
View 2 Replies
View Related
Jul 26, 2011
We have a CISCO 7604 Router (GGSN) in our customer site. Since two weeks are observing high CPU utilization (even touching 100 percent). We performed a SNMP configuration on this routers 2 weeks back as well. But SNMP process is not consuming much CPU resources. The following is the output of the "show proc cpu" and "show proc cpu history.
------------------ show process cpu ------------------
CPU utilization for five seconds: 50%/15%; one minute: 49%; five minutes: 51%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code]......
View 1 Replies
View Related
Jan 6, 2013
what is the meaning of the following log messages on Cisco 7604 Core routers. The Core router is configured with 2 STM card configurations with Vlan assignments: [code]
View 3 Replies
View Related
Jun 21, 2011
We currently run 7206 routers with VAM cards and are able to configure the devices to perform stateful failover of tunnels from router to router. When moving to the 7604 with 15.1 IOS there are not any examples of how to set up the stateful failover of the tunnels between devices. We have the devices in the SSO mode are not able to understand how to get the redundancy between the devices functioning.
View 1 Replies
View Related
Dec 20, 2012
I have 7604 router with FWSM module in module 3.First of all the FWSM CF has been damaged, not physically. I bought the new same compact flash (size, partnumber, etc.). Downloaded the software 3.2 for FWSM, and ASDM from Cisco website. I realized that the procedure of creating new CF for FWSM is quite diffucult: creating 1-5 partitions, where 1 - is MP, and 4th - application partition. According to cisco documentation - the default boot partition is the 4th, so I partitioned from 7604 the CF into 4 partitions (partition disk1: <1-4> maximum) and copied the software and ASDM to the 4th partition (disk1:3:). Removed the CF from the router and put it into the FWSM module.
View 1 Replies
View Related
Jul 9, 2012
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
[Code]......
View 2 Replies
View Related
Dec 13, 2009
following errors message:I have a 7604 with the following IOS
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-ADVIPSERVICESK9-M), Version 12.2(33)SRB5, RELEASE SOFTWARE (fc2)
but for some days now I am receiving the following error:
Dec 13 09:51:37.737 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continuesDec 13 15:30:17.392 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERRORDec 13 15:30:17.392 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continuesDec 13 21:17:24.225 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERRORDec 13 21:17:24.225 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continuesDec 14 04:42:03.363 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERRORDec 14 04:42:03.363 CET: %SYSTEM_CONTROLLER-3-MISTRAL_RESET: System Controller is reset:Normal Operation continuesDec 14 06:27:10.935 CET: %SYSTEM_CONTROLLER-3-ERROR: Error condition detected: TM_NPP_PARITY_ERROR
View 4 Replies
View Related
May 21, 2013
I have router Cisco 2691 and Cisco 7604 and want to play with AutoQoS Cisco feature. But on both there is no such command But why?
View 1 Replies
View Related
Sep 20, 2011
I have two 7604 routers running IOS 12.2(33)SRB5a as ASBRs in my network. They both connect to a common AS via DS3 lines.FR01 is considered my main circuit, FR02 is the backup. But I have some heavy disk sync traffic I want to route via the backup unless that circuit is down.How could a static redistribution possibly influence all my routes ?
Here is the remote AS config on both routers. We summarize the routes and only change the redistribute metric to distinguish main from backup circuit :
[code]...
View 12 Replies
View Related
Jul 14, 2012
i read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
View 4 Replies
View Related
Sep 2, 2012
I was called into a company today to look at their Cisco 7604 router as it had stopped working. The supervisor has all it LED in orange state, there was no blinking of the lights at power on they went straight to orange. Tried removing all cards, having only supervisor card in, etc but always the orange lights.
View 2 Replies
View Related
Jan 30, 2012
Some of which use snap and some use mux, the router is the one will start the connection and will always be on, untill there is a power cut, if there is. At this point when the power comes back on and a packet's destination is the outside the router should initiate a connection over the atm.
•Do not use this feature on a router that initiates PPPoA sessions.
•This feature supports ATM PVCs. Switched virtual circuits (SVCs) are not supported.
•PPPoA does not support static IP assignments within virtual templates.
The second and thrid I can understand and the 3rd will just get assigned an IP address from the ISP.But with the first point how is it possible to set this up when the router cannot initate the connection?
View 1 Replies
View Related
Nov 28, 2011
Is it possible to auto-shutdown for netgear router
View 1 Replies
View Related
Apr 21, 2011
I am trying to sort out an IP problem on my mates PC. I have setup a Linksys wireless router on his home broadband and it works fine with my laptop and gives me a DHCP address. When I try to connect his home PC either with a wireless dongle or ethernet connect it gets a Public IP address through the router and not one of the DHCP addresses. Even if you give it a static IP address and setup the router to accept it when you turn the PC on it still gets this public IP address. It is associating with the wireless router but only gives a local connection. I have done the ipconfig and it just renews the public IP address to a different one
View 3 Replies
View Related
Nov 14, 2011
Assuming I have the following setup: Cisco 7604 Cisco Systems Cisco 7600 4-slot Chassis System OSR-7600 Clock FRU 1 & 2WS-F6K-MSFC2A Cat6k MSFC 2A daughterboard Rev. 4.0 WS-F6K-PFC3B Policy Feature Card 3 Rev. 2.4 WS-SUP32-GE-3B 9 ports Supervisor Engine 32 8GE Rev. 4.6 WS-X6148A-GE-TX 48-port 10/100/1000 RJ45 EtherModule Rev. 4.1WS-X6548-GE-TX SFM-capable 48 port 10/100/1000mb RJ45 Rev. 11.3 The SUP32-3c says it supports both L2VPN and L2TPv3, however the line cards are effectively 6500 line cards and I was under the impression the 6500 didn't support these.
If the supervisor supports a feature does that mean it is globally supported on a switch? Or do I need to check the compatibility of these line cards as to if they support these features?
View 1 Replies
View Related
Dec 7, 2012
i have the topology :=========want to mention that im using port address translation on the router & not sure if it is making a conflict .
here is the config below :
why the cache is not working ?i mean that i tried going to internet with source ips of the subnet 10.20.30 , but i seems went to internet without any precedence of cahce server
[code]...
View 1 Replies
View Related
Jan 30, 2013
I'm just wondering if there is any documentation that confirms if the 2 built-in Gigabit ports on a Cisco 2851 router support (or otherwise) auto-mdix.I can find information for the modules but not the 2 built-in ports.
View 3 Replies
View Related
Apr 11, 2012
I usually put some stuff up for downloading and go to sleep. Now I setup my computer to auto-shutdown at a particular time via cmd, but I want o know whether it is possible for me to put some time settings in my modem+router so that it switches off at a particular time or something like that.Then when I get up next morning, start using it again. I don't want to keep my router on after it's not needed. Also I don't wanna keep it vulnerable after it's not needed, even though I have set it up quite securely. ( WPA2 PSK, and MAC filtering)
View 5 Replies
View Related
May 9, 2013
My Cisco 3900 router is not taking the no auto summary command?
View 5 Replies
View Related
Dec 14, 2012
Region : Malaysia
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.13.12 Build 120703 Rel.58323n
ISP :
I'm using the TL-MR3220 hardware version 2.0. Firmware version 3.13.12 Build 120703 Rel.58323n. I'm using D-Link DWM-156 3.75G HSUPA USB Adapter.The problem I'm encountering is the router does not auto detect the 3G USB adapter when I power up the router. The router will detect the 3G adapter only when I plug out and plug in the 3G USB adapter. I used to have the same router but version 1.2. Version 1.2 does not have this problem.
View 4 Replies
View Related
Aug 5, 2012
we are busy with a local service provider ( ISP ) and they want to evaluate the SRP500 series and have a few questions that i cant answer clearly.
Can the router auto provision back to the ISP's site , aside from the USB bootup option. i.e manufacture programmed "version "to dial into a specific ISP to provision.
Central administration of SRP500 series: Can the ISP manage and update/ close down SRP500 from a central point. I know the TR069 is std on the SRP500 series, but what does this encompass.
View 1 Replies
View Related
Aug 20, 2011
I'm a bit confused about what a wireless range extender gives me. I have bought a Sitecom Wireless Range Extender 300N. This extends the wireless range of your router to parts of the house that have a weak signal or none atall.
It is setup correctly and is working fine, however, the SSID is different from the Router.
Essentially, I want to extend the range of my router to parts of the house that have a low signal. This range extender seems to be the correct product to do this. However, I want my clients to switch to the appropriate wireless access point (either the range extender or my router) depending on the strongest signal, how can this be configured?
When a client is the overlap area (the area where both the router and the range extender can be sensed) I want the client to switch to the strongest signal.
In my case My Router is in the loft and the range extender downstairs. You can still get a low signal from the router when you are downstairs but the range extender give a full signal. However, I dont understand what makes a laptop 'switch' from router to extender when its downstairs.
Because the extender has a different SSID a laptop that can still get a low signal from the router when downstairs doesn't automatically attach to the extender to get a strongest signal.
If I set the extender to have the same SSID as the router
View 1 Replies
View Related
Jul 9, 2012
Example config
int g2/24
service-policy output test
#and/OR
int g2/24.10
encap dot1q 10
ip address 10.1.1.1 255.255.255.0
service-policy output test
View 5 Replies
View Related
Apr 25, 2012
Any direct download of the EA2700 firmware upgrade. My inet is not dsl or cable and will not let the wan port connect, therefor the "auto firmware update" will not work. I'd like to update it and see if it fixes it before I return this for a dlink. url...Anyways, I just want the firmware link so I can decide if this thing is going back to the store or not.
View 1 Replies
View Related
Apr 16, 2013
Purchased an EA4500 router. I'm using an old HP 4L laserjet and have it connected to the router via the USB port. I have 2 Mac's and installed vusb on both. I can successfully print from both Mac's, however I have to manually disconnect and connect the printer in the vusb client. I can't get the auto-connect and auto-disconnect settings to work by themselves. Any guidance on the proper settings here?Additionally, do I need to configure the printer driver though the vusb client? When I click "configure", I get an error saying"Cannot connect to Prolific Technology Inc. IEEE-1284 Controller.
View 3 Replies
View Related
