Cisco WAN :: Resetting Password For 7604 Router?
Jul 30, 2012I have tried to reset the password for 7604 but it is not working. At the rommon mode, i input 0x2142, and then reset.
It reloads and keeps asking for password.
ADVERTISEMENT
Linksys Wireless Router :: Resetting Password On WRT120N?
Dec 24, 2011Turns out one of the relatives changed the router name and password, and in a fit of brilliance, forgot to WRITE THE NEW USERNAME/PASSWORD DOWN!So I typed in 192.168.1.1 and tried literally every combination I know. NOTHING works tried rebooting the WRT120N. I tried both holding the reset button in, as well as holding the reset button in along with pulling the power adapter cord. Neither of these achieved the desired result (which would be the resetting of the factory username and password to "admin/admin".
View 2 Replies View RelatedCisco Switching/Routing :: How To Make Password Recovery For 7604
Jul 14, 2012i read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
Linksys Wireless Router :: Retrieving Or Resetting Password On EA6500
Jan 9, 2013How do I either retrieve or reset the router password? To edit it you have to have the current password, which it doesn't display. If I want to reset it do I have to do a factory reset on the router? If I do that, then I have to set everything up again.
View 3 Replies View RelatedLinksys Wireless Router :: Resetting Cisco E1200 - Cannot Remember Password
Jan 5, 2013I can't remember my password and I am locked out. How can I reset?
View 1 Replies View RelatedLinksys Wireless Router :: Wrt54g V2 Reset Button Not Resetting Password?
May 13, 2013I was given this router (it's my 3rd one) and cannot get the reset button to reset the password. I have run throught a 30/30/30 reset as well as just holding the button in for the standard 30 seconds.
I know the router works, as in i can ping it. It asks for a password when i go to 192.168.1.1, but *blank* and "admin" do not work. When i click the cancel button it displays a pink(salmon) screen that says "401 Unauthorized Authrization required". (all of this is when i am connected to it with an ethernet cable to #1)
When it's sitting there it has an led lit over power and one ove wlan which flickers from time to time.
Linksys Wired Router :: Rv042 - Set Password Without Resetting To Factory Default?
Apr 3, 2012Last year our Network Security Supervisor submit his resignation and unfortunately did not endorse us the admin password we already tried the password he suggested when we contacted him but nothing of them works. Is there anyway we can reset the password without resetting to factory default?
View 1 Replies View RelatedResetting Wifi Password Using Modem?
Dec 14, 2012im trying to do is reset my wifi password so that i can get internet for my moms new lap top.
i have a sb5102 cable modem and i need to change the password , how do i do that??
Cisco VPN :: Resetting Enable Password On ASA5505 Device
Jul 9, 2012resetting the disable password on an ASA5505 device
View 9 Replies View RelatedCisco Firewall :: ASA 5505 - Download Configuration Before Resetting Password?
Mar 24, 2013I am new with ASA devices I have a ASA 5505, the former IT manager does not remember the password of it. I am just wondering do I lose the configuration on it if I reset the password?if yes, how can I download the configuration before resetting the password. and how can I upload the downloaded configuration
View 2 Replies View RelatedCisco WAN :: No Duplex Auto On 7604 Router
Oct 18, 2011I have a 7604 Edge router that connects to our Data centre via Fiber.
but i keep getting input errors on the interface Gi3/5. i also found out that i cannot change the duplex settings on the edge router to auto, i only have two options of full and half and changing it has not worked either.
I have tried to use a switch in between the fiber modem and the edge router to try to manipulate the duplex settings, but when i tried it the port simply shutdown and then i have to reverse the configuration.
The software version of the router is 12.2(33)SRE3, i really need to sort this out as connection to and from the Data centre is quite slow.
Cisco :: Cisco Command For Resetting Password?
Feb 27, 2012I have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 Replies View RelatedDisable Resetting SMC Router?
May 11, 2012is there a way to disable reseting SMC router
View 1 Replies View Related4G Cradlepoint Router Keeps Resetting?
Feb 2, 2011I'm trying to get an MBR1000 Cradlepoint 4G router working, but every time I plug the 4G aircard in, the router constantly resets itself about every 10 seconds or so. If I take the aircard out, the router is fine (of course doesn't have internet connection), and I can plug the card into a PC and it works fine. I talked to Verizon, and they told me that the air card that we DID have wouldn't work with a router, so they exchanged it and gave us a newer one. The 4G card is the Pantech UML290. I've tried everything I can think of, including updating the firmware on the router (and the router's 4G firmware), I've reset the router to default settings in case a setting got messed up.The guy at Verizon told me that I should basically be able to plug it in and have it work.
View 1 Replies View RelatedCisco VPN :: Setting Up A GRE Using IPSEC On 7604?
Jun 27, 2011To establish s secure tunnel using GRE with IPSec do I need to add a SPA-IPSEC module to my 7604 chassis?
View 1 Replies View RelatedCisco WAN :: 7604 QoS On GRE Tunnel Interfaces
Aug 31, 2011I want to implement QoS on our Core router but the core router makes use of GRE Tunnels to remote branch locations.so far all QoS techniques i want to use cannot be implemented using tunnel interfaces.
the core router is a cisco 7604 router with IOS version 12.2 (33)SRE while the remote locations have ISRs (2821).
Which QoS technique to use with respect to GRE Tunnels as there are times of congestion due to heavy network traffic to those remote locations.
Resetting Linksys WRT54G Router?
Jul 3, 2011Well the model of my linksys is in the title so If you need It have a look at the title, so what I wanted to know was, what exactly does resetting my router do (be as detailed as possible) Is It hard to reset a router? and do you think that in my case resetting is necessary.
I forgot my wpa key, also my default password Is not "admin" I'm pretty sure I changed it after I got my router.
Printers Offline After Resetting Router?
Mar 21, 2011I added a VOIP fax line to my network and in doing so, was forced to reset my router, as it would not go on-line. Now the printers are all off line and I can not get them back online. I followed instructions within admin and it did not work. My network is a 2 computer network. My computer acts as server and then one other computer.
View 2 Replies View RelatedCan't Access Router Configure After Resetting
Dec 1, 2012I have a Netgear WNR1000v3 router that I just reset to factory defaults, and now when I run ipconfig /all it doesn't show up as having a gateway. Note that I am connecting with a laptop wired in to a LAN port on the router. (also tried on WAN port) Here is what shows up:
SpoilerEthernet adapter Local Area Connection:
Ubee Modem / Router Keeps Resetting Itself
Aug 6, 2011I have Charter Communications Internet Service the 18MB Service. All Day today the Modem kept Resetting itself as if I had the modem plugged into a lightswitch, Called Charter and they gave me the run around. Im leasing this Cable Modem / Router all in one from them, its a Ubee DDW3611 Docsis 3. Here are the Event Logs as well as my Signals Right here,
[code]....
Cisco WAN :: Software Requirements For Supporting XFP In 7604?
Jul 15, 2012We have a 7604 chassis with the following equipments:
1. RSP720-3C-10GE
2. 7600-SIP-400
3. SPA-1X10GE-L-V2
We would like our SPA to support XFP transceiver having part number XFP-10GZR-OC192LR.
Cisco WAN :: High CPU Utilization In GGSN (7604 Ios 12.4)
Jul 26, 2011We have a CISCO 7604 Router (GGSN) in our customer site. Since two weeks are observing high CPU utilization (even touching 100 percent). We performed a SNMP configuration on this routers 2 weeks back as well. But SNMP process is not consuming much CPU resources. The following is the output of the "show proc cpu" and "show proc cpu history.
------------------ show process cpu ------------------
CPU utilization for five seconds: 50%/15%; one minute: 49%; five minutes: 51%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code]......
Cisco WAN :: 7604 Logs Explanation Required
Jan 6, 2013what is the meaning of the following log messages on Cisco 7604 Core routers. The Core router is configured with 2 STM card configurations with Vlan assignments: [code]
View 3 Replies View RelatedCisco VPN :: 7604 - Get Redundancy Between Devices Functioning?
Jun 21, 2011We currently run 7206 routers with VAM cards and are able to configure the devices to perform stateful failover of tunnels from router to router. When moving to the 7604 with 15.1 IOS there are not any examples of how to set up the stateful failover of the tunnels between devices. We have the devices in the SSO mode are not able to understand how to get the redundancy between the devices functioning.
View 1 Replies View RelatedInternet Works On All Computers But One After Resetting The Router
Feb 26, 2013we hadn't have the WEP key on our Linksys wireless router, so we decided, about a month ago, that it was a good idea to lock our wireless connection. So we did. For a couple of weeks, everything worked just fine.But then we bought a new printer, which happened to be a wireless network printer, and in the process of installing it, we mistook the reset button (I think) on the router for some other button and ended up resetting the router. When we did that, we undid WEP key, thereby unlocking the router. Then, we locked the router again, at which point one of our computers--which happens to be mine--ended up not working. All other computers and phones and iPads work just fine, but this one laptop of mine just doesn't work (with respect to wireless internet connections, of course).
- pressing the reset button on the router again. It kind of works. The internet works for about five or ten minutes (which is unbearably annoying because I have to reconnect it every five minutes), but my computer somehow disconnects itself from the internet connection. Also, although the internet technically "works," the wireless network icon thing on the bottom right of the screen has an "X" on it, which I thought meant the internet is not working, but it apparently doesn't, because my internet is working now. And, if I click the icon, it says that I'm not connected, but, again, the internet works. (for about 5~10 minutes, if I unlock the router)
- changing the internet protocol information (I don't think it does anything, but.)
- changing the wireless internet connection property to WPA, WPA-PSK... everything.
*All computers in the house have wireless internet connections but mine.
*When I reset the router, the internet works, although the computer says it isn't connected, and it disconnects itself every 5 or 10 minutes.
Slow Download Speeds Even After Resetting Router
Nov 9, 2011I usually get a solid speed of 2.3MBss yet today I am getting only 500kb/s I have reset my router 3 times, and my computer twice. Why is it happening?
View 1 Replies View RelatedResetting Modem / Router To Factory Settings
Oct 8, 2011Got a Belkin wireless modem router some 18 monthes ago, and after a bit of a struggle managed to set it up. It worked fine, aside from the odd depower repower. For some reason, it just stopped working yesterday. I initially checked all my cabling etc and everything seems fine. I next tried resetting my modem/router to factory settings. When I tried to install the Belkin software I fell at the first hurdle with a message saying "The setup assistant is not able to connect to the router". After googling my issue, I followed others advice and running the cmd setting and typing in "ipconfig" only to find that my media state was disconnected.
View 2 Replies View RelatedLinksys Wireless Router :: Why Need To Keep Resetting E2500
Nov 18, 2011So, i have a e2500 router and find that every so often, I have to unplug it and reset it because I am losing my internet connection.
View 7 Replies View RelatedLinksys Cable / DSL :: WAG160N Router Resetting Itself
May 24, 2011I purchased a new WAG160N router a few months ago and recently I have been having major problems with connectivity.The problem is that it resets itself at seemingly random times. I see it happening. The red power light starts flashing red and then the other lights slowly turn green as it re-establishes connection to the internet.
This is becoming extremley frustrating as I do online gaming with my XBOX 360.I use wired connections using ethernet cables. One to my laptop. And one to my XBOX 360.I have contacted my ISP who have done line checks and I have had an engineer look at my line and all is good. I have also replaced all cables to/from the router including phone cords and ethernet cords. EVERYTHING is new.I recall one incident in which my internet was down and I just couldnt get connection AT ALL. I rang my ISP and they got me to log into my modem settings. The settings were all altered for some reason and I have no idea why. When they told me to enter the details in the settings the internet worked immediatley.
Linksys Wireless Router :: WRT120N Keeps Resetting On Its Own?
Jan 18, 2010My roommate and I recently got a WRT120N to replace an older Linksys router that was exhibiting the same problems with less frequency. Indeed, the entire reason we got the new router was to fix these problems. Alas, they have become worse.Anyways, what's happening is that the router constantly resets itself. It does this every 20 minutes to an hour and doesn't seem to be related to how much traffic it's dealing with.It's not just the internet going down, it's the entire network, and not even just the wireless part. My computer has a wired connection to the router and, and I get told "A network cable has been unplugged" every time it happens. Then, if I look down at the router, I see no flashing lights, just the steady glow of the power light. It always fixes itself after 10-15 seconds, but it's very annoying. Certainly, playing games online or having a conversation on Skype is made more difficult.As previously mentioned, we replaced our older router because it was exhibiting the same behavior, but the new one does it with greater frequency. At the very least, the router does reset itself instead of needing us to cycle the power. The setup was slightly different with the old router: I was using a wireless connection with a WMP54Gv4 which I've had to disable since it bluescreens the moment it so much as sniffs a signal from the WRT120N?
View 9 Replies View RelatedCisco Switching/Routing :: Factory Resetting 1941 Router
Oct 27, 2011What is the procedure to reset a 1941 router to factory defaults? I just recieved my1 1941 router. I connected it up to my Mac using USB. I got loged in using the cisco/cisco login and it said it will only work once and that I should create a new account. So I entered the command as directed on the screen and it gave my an error about the command. I verified it three times and each time it rejected. While I was looking online for an answer the connection timed out and now I can't get back in.
View 1 Replies View RelatedCisco Firewall :: 7604 FWSM Boot Failure
Dec 20, 2012I have 7604 router with FWSM module in module 3.First of all the FWSM CF has been damaged, not physically. I bought the new same compact flash (size, partnumber, etc.). Downloaded the software 3.2 for FWSM, and ASDM from Cisco website. I realized that the procedure of creating new CF for FWSM is quite diffucult: creating 1-5 partitions, where 1 - is MP, and 4th - application partition. According to cisco documentation - the default boot partition is the 4th, so I partitioned from 7604 the CF into 4 partitions (partition disk1: <1-4> maximum) and copied the software and ASDM to the 4th partition (disk1:3:). Removed the CF from the router and put it into the FWSM module.
View 1 Replies View RelatedCisco Switching/Routing :: HSRP Flapping On 7604?
Jul 9, 2012i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
[Code]......