I have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 RepliesI have tried to reset the password for 7604 but it is not working. At the rommon mode, i input 0x2142, and then reset.
It reloads and keeps asking for password.
resetting the disable password on an ASA5505 device
View 9 Replies View Relatedim trying to do is reset my wifi password so that i can get internet for my moms new lap top.
i have a sb5102 cable modem and i need to change the password , how do i do that??
I am new with ASA devices I have a ASA 5505, the former IT manager does not remember the password of it. I am just wondering do I lose the configuration on it if I reset the password?if yes, how can I download the configuration before resetting the password. and how can I upload the downloaded configuration
View 2 Replies View RelatedI can't remember my password and I am locked out. How can I reset?
View 1 Replies View RelatedTurns out one of the relatives changed the router name and password, and in a fit of brilliance, forgot to WRITE THE NEW USERNAME/PASSWORD DOWN!So I typed in 192.168.1.1 and tried literally every combination I know. NOTHING works tried rebooting the WRT120N. I tried both holding the reset button in, as well as holding the reset button in along with pulling the power adapter cord. Neither of these achieved the desired result (which would be the resetting of the factory username and password to "admin/admin".
View 2 Replies View RelatedHow do I either retrieve or reset the router password? To edit it you have to have the current password, which it doesn't display. If I want to reset it do I have to do a factory reset on the router? If I do that, then I have to set everything up again.
View 3 Replies View RelatedI was given this router (it's my 3rd one) and cannot get the reset button to reset the password. I have run throught a 30/30/30 reset as well as just holding the button in for the standard 30 seconds.
I know the router works, as in i can ping it. It asks for a password when i go to 192.168.1.1, but *blank* and "admin" do not work. When i click the cancel button it displays a pink(salmon) screen that says "401 Unauthorized Authrization required". (all of this is when i am connected to it with an ethernet cable to #1)
When it's sitting there it has an led lit over power and one ove wlan which flickers from time to time.
Last year our Network Security Supervisor submit his resignation and unfortunately did not endorse us the admin password we already tried the password he suggested when we contacted him but nothing of them works. Is there anyway we can reset the password without resetting to factory default?
View 1 Replies View RelatedWe have a cisco 2801 router in class which has a disabled password recovery. We tried almost everything, we cannot get into ROMmon and the break sequence doesn't work in any program (hyper terminal, putty, teraterm pro).
Here is the log from hyperterminal:
System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)Technical Support: [URL].Copyright (c) 2004 by cisco Systems, Inc.PLD version 0x10GIO ASIC version 0x127c2801 processor with 131072 Kbytes of main memoryMain memory is configured to 64 bit mode with parity disabledReadonly ROMMON initializedPASSWORD RECOVERY FUNCTIONALITY IS DISABLEDprogram load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xc100Initializing ATA monitor library.......program load complete, entry point: 0x8000f000, size: 0xd49718Self decompressing the image :
[code].....
I want to telnet a router (say) 1.1.1.1 with usename "user" and password "pass" in command line. i tried using....telnet 1.1.1.1 -l user ..........but not working
View 3 Replies View RelatedHow to find the password through lan or cmd
View 2 Replies View RelatedI enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
We have an ASA5510 which keeps resetting itself for no apparent reason. It does this several times a day and I cannot see any pattern to the times etc. I don't believe it is load related as it also happens overnight when very little is going through the device. When it happens the device just drops off the network (all interfaces) and then when it comes back a few minutes later we can see from the system uptime that it has in fact rebooted itself.I initially thought it was faulty hardware, so I swapped the device for another 5510, but that does the same thing. I then added a third 5510 and configured it in with the second one as an Active/Passive failover pair. Both devices do the same as the first, the only differences now is that the passive device kicks in and takes over, so we have a little less service disruption each time.
View 9 Replies View RelatedThis summer the IT department at my location rolled out a little more than 100 AIR-CAP3502I-A-K9's to much success. We have had an issue with only one AP. This paticular AP must have gotten unplugged during the updating process after the initial conneciton to the controller was made as the LED currently blinks red-blue-red, indicating an error in the flash memory according to the manual.
View 2 Replies View RelatedI would like to empty my LMS 3.2 DB and re-discover all of my devices again. What is the best way to do this besides wiping the software and reinstalling?
View 1 Replies View RelatedWe have an ASA5510 which keeps resetting itself for no apparent reason. It does this several times a day and I cannot see any pattern to the times etc. I don't believe it is load related as it also happens overnight when very little is going through the device. When it happens the device just drops off the network (all interfaces) and then when it comes back a few minutes later we can see from the system uptime that it has in fact rebooted itself.
I initially thought it was faulty hardware, so I swapped the device for another 5510, but that does the same thing. I then added a third 5510 and configured it in with the second one as an Active/Passive failover pair. Both devices do the same as the first, the only differences now is that the passive device kicks in and takes over, so we have a little less service disruption each time.
I have to keep restting my wep key password for my wireless lap top to access the router. It stays logged on for some time but then is looged off the internet. I have to reset the wep key using my desk top PC and each times the default setting is NOT the password I use. after resetting the lap top recognises the web and I can gain access again. Howver this cycle keeps repeating itself!!! Do I have a hacker who keeps resetting my wep key for their own use?
View 2 Replies View RelatedWe have recently received some used computing gear for HPC. With that came a Cisco SFS 7024 infiniband switch, which should handle the compute traffic of the cluster. As the system has been used before, i would like to reset the switch, to configure it anew for our setup. Normally with switches there is a possibility to factory reset it, but I have looked everywhere on the switch and in the online manual with out any luck.I have gone through the part where an OOB IP is given to the switch. I do however not know if the former users has changed this, and what it might be.
View 4 Replies View RelatedI have tried to reset a Cisco 2811 to factory defaults to no avail. The system is locked, meaning it's set to go immediately to username and password before doing anything else after boot up. I cannot get to ROMMON, nor can the CTRL-B break sequence allow me the option. THere is a "no-password recovery" option that apparently is set (or unset?) but I cannot work with that.
I am a newbie with the routers, but I have tried various CTRL-B breaks from bootup, to particular times through the boot up sequence.
I do NOT have "enable" (also known as "privileged EXEC") access on the router. The router, when purchased, had a username and PW that is required to even get to the basic level 1 access. Without it the PW, I can't even get to exec mode.
I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies View RelatedIf I enable both radio interfaces on new 892W with integrated access-point 801 the radio interfaces are reseting every 30 seconds. I have already tried different IOS version 12.x and 15.x on the router and the integrated ap. Also tried a a configuration from another 892W, which is working fine on the other router. Still same issue. If I disable one of the interfaces, doesn't matter which, the access point ist working fine.With both enabled log of the ap shows:
Mar 8 19:09:26.403 MEZ: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Mar 8 19:09:27.583 MEZ: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
Mar 8 19:09:28.175 MEZ: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
Mar 8 19:09:28.203 MEZ: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
[code]....
This router keeps dropping all connections under a load of about 30 devices. everyone will lose internet access for a few minutes until it comes back. All settings are correct.This doesn't happen unless around 20-30 users are actively using their connections, both wired and wireless.
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] IP: 68.84.158.86
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] BCAST: 255.255.255.255
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] SUBNET: 255.255.254.0
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] GW: 68.84.158.1
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] DNS1: 75.75.75.75
[code]....
I have 2 WRVS4400N routers that were installed at 2 remote locations to provide VPN access to these sites. The routers have been found reset to the factory defaults on three occasions, twice on one of them and once on the other. Both sites are unmanned so no-one is on site to have pressed the reset button, and both routers were set to have remote management disabled. They are running v2013 firmware.
View 3 Replies View RelatedI have a Linksys SRW2008MP that I am trying to reset to factory defaults. The guy who set this up is no longer employed at my company, and I do not know the IP address to login with a web browser. The switch does not have a reset button on the back. I follow the instructions from Cisco's website, which include connecting a console cable and using HyperTerminal to login. I can connect to the switch and watch it boot up in HyperTerminal. However, when I get to the point of inputting user name and password (which should be 'admin' and '<blank>', I can't figure out how to make to terminal emulator accept the input (much like pressing the Enter button in a web browser). According to the pictures on Cisco's website, there should be an Action -> Edit -> Execute option down below the login, but I don't see it, so maybe the switch has to verify my credentials before I get to that prompt?
This is the first time in my life using HyperTerminal, and I think that's where my problem is. How do I get HyperTerminal to accept my input?
I have also tried using TeraTerm, a different console cable, and a different computer.
I am at the rommon screen getting the > sign
Rommon 1>
When I am typing confreg 0x2142 I am just getting “rommon 2>” and if try again I will get “rommon 3 >”
No reset prompt , this never happened to me
I have an 1841 (256M w/ crypto card) that stopped booting. I reset it to factory defaults as per Cisco's directions, then began to setup with Cisco Configuration Professional. On the next reload I get this:
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
[code]...
The ios on the flash is "c1841-advsecurityk9-mz.124-22.T.bin"
I have two 1252ag wireless access points running in lightweight mode, and connected to a 2006 wlc. They were both running fine until this morning. One of the 1252s won't stop rebooting itself. I consoled in, and this was the output -
*Mar 1 00:00:32.055: %LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER
*Mar 1 00:00:32.055: %LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER
*Mar 1 00:00:32.055: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
[ code].....
IOS Boot loader - Starting system. X modem file system is available. I'm particularly curious about this line -
*Mar 1 00:00:50.283: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
The only reference to it I found online was a very vague "It's a hardware failure", but no further explanation.
Alright so, for the past few weeks, the modem has been resetting itself, by that I mean, I am browsing the net/playing something, then the four lights turn into 1 blinking.. then 2 blinking.. then 3 blinking.. then return to 4 lights and I get my connection back, this is happening every 5-10 minutes and terminates game sessions.
View 1 Replies View Relatedis there a way to disable reseting SMC router
View 1 Replies View RelatedRecently, whenever I download something my internet will just crash for a second, I think it may be realted to my router because the internet light on my router changes from the connected state (solid blue) to the connecting state (flashing orange) at the same time. The router I use is a belkin router and I have access to its gateway using my internet browser. recently reformatted my c drive to fix a bsod on this pc, before this reformat this problem did not exist.
View 5 Replies View RelatedI'm trying to get an MBR1000 Cradlepoint 4G router working, but every time I plug the 4G aircard in, the router constantly resets itself about every 10 seconds or so. If I take the aircard out, the router is fine (of course doesn't have internet connection), and I can plug the card into a PC and it works fine. I talked to Verizon, and they told me that the air card that we DID have wouldn't work with a router, so they exchanged it and gave us a newer one. The 4G card is the Pantech UML290. I've tried everything I can think of, including updating the firmware on the router (and the router's 4G firmware), I've reset the router to default settings in case a setting got messed up.The guy at Verizon told me that I should basically be able to plug it in and have it work.
View 1 Replies View Related