Auto-shutdown For Netgear Router?
Nov 28, 2011Is it possible to auto-shutdown for netgear router
View 1 Replies
ADVERTISEMENT
Cisco Infrastructure :: Router 2901 Shutdown After 30 Or 50 Minutes
May 22, 2011why router going to shut down mode after 15 or 30 min? Here is the #show tech support command. find the attached document.
View 3 Replies View RelatedCisco WAN :: Router Rip And No Shutdown Commands Not Working On 2621xm?
Jun 16, 2012I have an old 2621xm router in CCIE lab at home. Only a week ago I started having issue on 2 of them. The problem is on one of them when I go under interface configuration and I type "no shut" nothing happens. Interface stays in administratively down status and when I check running config "shutdown" is still under interface.
On the other one the same problem but only with "router rip" command. I configure my rip routing but then when I check running config there is no rip section and also RIP is not running under "show ip protocols rip".These routers are connected to 2511 AccesServer. So I thought the issue might be communication from AccessServer to these devices. I connected a console cable straight to them and still the same problem. Everything else is working on these devices.
Cisco Switching/Routing :: 6500 Shutdown Interface On One Router / Deleted Secondary Address
Jul 15, 2012I have just updated a VLAN interface on my router. I have two 6500's with GLBP configured. The particular interface had a primary and secondary IP address. I shutdown the interface on one router and deleted the secondary address then assigned the orignal secondary address to be the be the only address associated with the interface and enabled the interface and it came right back up...all looks good. I proceeded to do the same thing to the other router and once again all looked good. Now, I am able to PING the devices in the subnet from router, but am unable to ping them from any place else. [code]
View 2 Replies View RelatedPC Gets Auto-IP From Internet Not From DHCP On Router?
Apr 21, 2011I am trying to sort out an IP problem on my mates PC. I have setup a Linksys wireless router on his home broadband and it works fine with my laptop and gives me a DHCP address. When I try to connect his home PC either with a wireless dongle or ethernet connect it gets a Public IP address through the router and not one of the DHCP addresses. Even if you give it a static IP address and setup the router to accept it when you turn the PC on it still gets this public IP address. It is associating with the wireless router but only gives a local connection. I have done the ipconfig and it just renews the public IP address to a different one
View 3 Replies View RelatedSet Modem / Router To Auto-switch Off At Particular Time?
Apr 11, 2012I usually put some stuff up for downloading and go to sleep. Now I setup my computer to auto-shutdown at a particular time via cmd, but I want o know whether it is possible for me to put some time settings in my modem+router so that it switches off at a particular time or something like that.Then when I get up next morning, start using it again. I don't want to keep my router on after it's not needed. Also I don't wanna keep it vulnerable after it's not needed, even though I have set it up quite securely. ( WPA2 PSK, and MAC filtering)
View 5 Replies View RelatedCisco WAN :: No Duplex Auto On 7604 Router
Oct 18, 2011I have a 7604 Edge router that connects to our Data centre via Fiber.
but i keep getting input errors on the interface Gi3/5. i also found out that i cannot change the duplex settings on the edge router to auto, i only have two options of full and half and changing it has not worked either.
I have tried to use a switch in between the fiber modem and the edge router to try to manipulate the duplex settings, but when i tried it the port simply shutdown and then i have to reverse the configuration.
The software version of the router is 12.2(33)SRE3, i really need to sort this out as connection to and from the Data centre is quite slow.
Cisco WAN :: 800 Series Router Auto-sense ATM Pvc
Jan 30, 2012Some of which use snap and some use mux, the router is the one will start the connection and will always be on, untill there is a power cut, if there is. At this point when the power comes back on and a packet's destination is the outside the router should initiate a connection over the atm.
•Do not use this feature on a router that initiates PPPoA sessions.
•This feature supports ATM PVCs. Switched virtual circuits (SVCs) are not supported.
•PPPoA does not support static IP assignments within virtual templates.
The second and thrid I can understand and the 3rd will just get assigned an IP address from the ISP.But with the first point how is it possible to set this up when the router cannot initate the connection?
TP-Link 3G/3.75G Router :: TL-MR3220 V2 No Auto Detect 3G Modem?
Dec 14, 2012Region : Malaysia
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version : 3.13.12 Build 120703 Rel.58323n
ISP :
I'm using the TL-MR3220 hardware version 2.0. Firmware version 3.13.12 Build 120703 Rel.58323n. I'm using D-Link DWM-156 3.75G HSUPA USB Adapter.The problem I'm encountering is the router does not auto detect the 3G USB adapter when I power up the router. The router will detect the 3G adapter only when I plug out and plug in the 3G USB adapter. I used to have the same router but version 1.2. Version 1.2 does not have this problem.
Cisco WAN :: 2851 Router Auto Mdix Feature
Jan 30, 2013I'm just wondering if there is any documentation that confirms if the 2 built-in Gigabit ports on a Cisco 2851 router support (or otherwise) auto-mdix.I can find information for the modules but not the 2 built-in ports.
View 3 Replies View RelatedHow To Shutdown A Mac Using Windows 7
May 6, 2012How do you shutdown a mac using win7 (on the same network) using the command line?win to win: shutdown -i then name or ip-address, what about win to mac? How does that work?
View 13 Replies View RelatedShutdown Remote PC In Same LAN
Jan 19, 2011There is another PC in my wireless LAN.is there any way to shut it down from my computer?currently two PCs are not shared .but connected to the same router.
View 13 Replies View RelatedCan't Shutdown PC With Same Ip Address
Aug 20, 2011I run cmd, as an Administrator, After typing shutdown -i the Remote Shutdown Dialog Window pops up,Giving me a lot of posibilities. Though, in the "computers" section there's nothing. Though the main house computer is connected to the same network as the laptop I am at. I wondered why isn't the computer there? So I typed net view in cmd , and only the laptop's name was there. Meaning? The two computers are connected to the same network, thats for sure, the ip's last number in the main pc is 1 and in the laptop is 2. But this is which port each computer is using right?
View 4 Replies View RelatedAuto-switching Clients Between Router And Wireless Range Extender
Aug 20, 2011I'm a bit confused about what a wireless range extender gives me. I have bought a Sitecom Wireless Range Extender 300N. This extends the wireless range of your router to parts of the house that have a weak signal or none atall.
It is setup correctly and is working fine, however, the SSID is different from the Router.
Essentially, I want to extend the range of my router to parts of the house that have a low signal. This range extender seems to be the correct product to do this. However, I want my clients to switch to the appropriate wireless access point (either the range extender or my router) depending on the strongest signal, how can this be configured?
When a client is the overlap area (the area where both the router and the range extender can be sensed) I want the client to switch to the strongest signal.
In my case My Router is in the loft and the range extender downstairs. You can still get a low signal from the router when you are downstairs but the range extender give a full signal. However, I dont understand what makes a laptop 'switch' from router to extender when its downstairs.
Because the extender has a different SSID a laptop that can still get a low signal from the router when downstairs doesn't automatically attach to the extender to get a strongest signal.
If I set the extender to have the same SSID as the router
Cisco WAN :: 3900 Router Is Not Taking No Auto Summary Command
May 9, 2013My Cisco 3900 router is not taking the no auto summary command?
View 5 Replies View RelatedLinksys Wireless Router :: EA2700 Auto-firmware Update Will Not Work
Apr 25, 2012Any direct download of the EA2700 firmware upgrade. My inet is not dsl or cable and will not let the wan port connect, therefor the "auto firmware update" will not work. I'd like to update it and see if it fixes it before I return this for a dlink. url...Anyways, I just want the firmware link so I can decide if this thing is going back to the store or not.
View 1 Replies View RelatedLinksys Wireless Router :: EA4500 Cannot Get Auto Connection Settings To Work
Apr 16, 2013Purchased an EA4500 router. I'm using an old HP 4L laserjet and have it connected to the router via the USB port. I have 2 Mac's and installed vusb on both. I can successfully print from both Mac's, however I have to manually disconnect and connect the printer in the vusb client. I can't get the auto-connect and auto-disconnect settings to work by themselves. Any guidance on the proper settings here?Additionally, do I need to configure the printer driver though the vusb client? When I click "configure", I get an error saying"Cannot connect to Prolific Technology Inc. IEEE-1284 Controller.
View 3 Replies View RelatedCisco Routers :: SRP50 Can Router Auto Provision Back To ISP Site
Aug 5, 2012we are busy with a local service provider ( ISP ) and they want to evaluate the SRP500 series and have a few questions that i cant answer clearly.
Can the router auto provision back to the ISP's site , aside from the USB bootup option. i.e manufacture programmed "version "to dial into a specific ISP to provision.
Central administration of SRP500 series: Can the ISP manage and update/ close down SRP500 from a central point. I know the TR069 is std on the SRP500 series, but what does this encompass.
Cisco VPN :: 871 - Int Tunnel1 Shutdown And Not In Use
Nov 7, 2012Even though I've been working on Cisco way too long I've never worked with the 871 before, and I've never inherited a system with so many unused commands in the config. Apparently there have been a lot of changes over the years and a lot of commands left behind. And sure I'd like to clean it all up and start over, but I really just need it working right now.
There are a total of 4 sites, HQ and remotes1-3. HQ has an ASA, remotes the 871s, there are VPN tunnels between each 871 and the ASA and these are working fine.
Remote1 also has tunnels to Remote2 and Remote3, and these work.
Remote2 has the working tunnels to HQ and Remote1, but can't establish a tunnel to Remote3.
Remote3 has working tunnels to Remote1 and HQ, but not Remote2 (obviously)
They are all running the same IOS 12.4(20)T3 and have virtually identical configurations. A sho cryto sess on Remote2 and 3 look like this, with an obvious IKE problem;
Interface: FastEthernet4
Session status: UP-ACTIVE
Peer: xxx.xxx.xxx.x30 port 500
[code]......
The only differences in the configs are the IP and the self-signed keys might have different modulus. This is the config for Remote3, I've tried some different combinations of putting in static routes and not, so don't assume what's here is what's been tried. And I've already gone over the pre- shared keys and ACLs a hundred times. My gone is to just get it working, not make it clean. Note: int Tunnel1 is shutdown and not in use.
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
[code].......
Linksys Wireless Router :: WKPC54G / Change Or Modify The Auto Generated Network Key?
Jun 18, 2007How to change or modify the auto generated network key? I am trying to work around but no luck. Is there a way to do this or once you generate a network key it is a default.
View 5 Replies View RelatedLinksys Wireless Router :: E3000 5Ghz Auto(DFS) Versus Selecting Channel
Nov 15, 2012I have an E3000 Dual Band. On my 5Ghz channel, I can select Auto(DFS) or I can manually select a channel.First of all, what does the DFS stand for? My 2.4 GhZ channel only has Auto, not Auto(DFS).
Second, when I select Auto(DFS), my wireless speed defaults to 144Mbps, and is only a single channel (I can see it in the in SSIDer utility). When I manually select a channel, no matter what channel it is, I get 300mbps and I can see that the signal is two channels (for instance, 36+40). Why Auto(DFS) doesn't automatically select the best channel and fastest speed?
Servers :: How To Shutdown A Laptop Wirelessly
Aug 15, 2011I want to shutdown my friends laptop from my laptop at school, how?
View 2 Replies View RelatedCisco WAN :: How To Shutdown 2960 Switch
May 16, 2012how to shutdown the cisco switch 2960.......
View 5 Replies View RelatedLinksys Wireless Router :: E4200 - Reset To Factory Defaults / Enable IPV6 Auto
Aug 10, 2011I flashed the firmware and the ipv6 automatic is on disabled and I cannot set it to enabled.the 6rd tunnel option I can change but that has not effect- in fact from what I looked up it seems to be something used by some cable providers.hate to have to reset the router to factory defaults and then reset the network up - just to see if i can get the option to set IPV6 auto to enabled.
View 3 Replies View RelatedLAN Drivers Shutdown Computer On Large Files
Dec 31, 2012I can copy or past small files but on big files like DVD ISO which are about 5GB there is a sudden shutdown like a power out.This shutdown happens exactly when I click paste. It is not the temperature or virus or a bad xp install.I clean installed xp and installed the newest lan drivers from ECS.
View 6 Replies View RelatedCisco WAN :: ASR 1004 Shutdown / Reload Procedure?
May 2, 2012From PEC training - Cisco says to perform a proper ASR 1004 shutdown by executing 'reload' , then wait for bootstrap message to appear, then [before commencement of unpacking of the IOS] turn off the power switch. IS THIS ACCURATE. Anyone have any doc related to the recommended POWER DOWN process on the ASR 1004. We have a UPS cutover coming up and I want to be ready to power down and restart the new ASR 1004s we have - properly.
View 3 Replies View RelatedCisco :: WLC 2106 / Automated WLAN Shutdown
Dec 13, 2009we operate a number of 2106 WLC's some of which are in training centres, we have been requested by one customer that the SSID used for the users in the training rooms is only enabled between the hours of 9am - 6pm Monday to Friday.
As such im trying to find an automated method of disabling said WLAN automatically outside of these hours including weekends.
Im aware that the commands:
config wlan disable "WLAN ID"
config wlan enable "WLAN ID"
Can be used to perform the required function but getting them to trigger at the appropriate time is proving more of a challenge.
Dell :: Inspiron 14 3420 NIC Turns Off After Shutdown
Mar 28, 2013Dell Inspiron 14 3420
I have bee trying to make WOL work with no luck so far. The problem is that when I shut down my laptop (connected to AC power) the NIC also shuts down. I already unchecked the box "Allow this computer to turn off this device to save power" in the power management tab in advanced NIC properties.
I noticed that when I force shutdown my laptop (press the power button for 5 seconds), the NIC stays on and WOL works, but when I perform a regular shutdown, the NIC shuts down when windows shuts down.
Cisco Switching/Routing :: WS-C3750X-48T-S - No Shutdown / Not Working
Jan 5, 2013I'm experiencing strange issue with my WS-C3750X-48T-S.
Model number: WS-C3750X-48T-S
System image file is "flash:/c3750e-universalk9-mz.122-55.SE3/c3750e-universalk9-mz.122-55.SE3.bin"
This switch is situated on a remote site and on the 6th of January it was rebooted.
I still do not know the cause, but it might be power outage or smth. We are still checking. After the reboot I've noticed that one port on this cisco switch is in 'notconnect' state, while I'm pretty sure it should be 'connected'.
I've tried to shutdown the port adminstratevly and do the 'no shutdown' but this port remained in 'disable' state.
#sh run interface Gi1/0/5
Building configuration...
!
interface GigabitEthernet1/0/5
[Code].....
Cisco Switching/Routing :: What Is The Command To Shutdown 1841
Oct 28, 2012What is the command to shutdown a cisco 1841 (say, to add a module)? I know how to reload / reboot, but does not seem to find any command with an obvious name.
View 1 Replies View RelatedCisco Infrastructure :: 3750 - C3KX-NM-1G - Ports 2 And 4 Not Shutdown
Oct 26, 2011I've put a C3KX-NM-1G module into a 3750x but can only get ports 1,3 to stand up, ports 2 and 4 dont operate. ports 2,4 are not shutdown and dont come up with working SFPs etc in another switch.
View 1 Replies View RelatedCisco Wireless :: 3502i - Dot11 Interface Shutdown
Dec 15, 2012My 3502i suddently shutdown it's Radio interface and when I connect to it, I cans ee that the interface is shutdown. So tryign to enable it but the "configure terminal" command is not available. Is there any hidden command to go the priveledge mode?
______________
interface Dot11Radio0
no ip route-cache
shutdown
antenna gain 0
beamform ofdm
mbssid(code)
Cisco Infrastructure :: C3560 Port Shutdown Shut Up
Jul 13, 2011Is it possible to reduce de recoveery time after an interface shutdown? Current interface configuration is as follows and it takes 1 second to recover from a shutdown. I need to decrease this time.(Cisco Catalyst C3560) [code]
View 1 Replies View Related
