providing an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
Anybody know of a extension cable for this product? D-Link 14dBi Outdoor Direct Antenna (ANT24-1400) I need at least 10-15 feet of extra length.
View 1 Replies View RelatedI have to replace a 1230 with an 1262 AP.
All antennas have to be in the same direction on the AP and I guess when the old 1230 is working well the 1262 will be only better . Attached u see how I plan to mount the new AP versus the old one...
I want to install some AIR-ANT2566P4W-R antennas outdoor against the wall, the 2602e access points will be mounted on the interior side of the wall, altough the wall is 30cm thick, so I need some antenna extension cables.What type of coax extension cables would be recommended ?
View 1 Replies View RelatedAny cheap outdoor extension antenna that works with a Linksys wap54g? Not looking for anything too expensive. Just trying to bring wifi signal into a building.
View 1 Replies View RelatedI 'm administration an Aironet 1242ag, and we are currently buying an AIR-ANT1728 as antenna. The standard cable for the antenna is 0.9m long, and It could be insufficient for my needs.
So a few questions:
Can i extend it ?
AIR-CAB050LL-R could fit?
The connectors should be 1 male, 1 female?
how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies View RelatedI used 2 PC with gigabit NIC, use cat6 with short cable i've got speed 1000Mbps, but with longer cable(around 30meters) speed is 100Mbps. I'm looking forward to seeing from you soon.
View 1 Replies View RelatedMaximum length of cat 6 lan cable between two switch
View 2 Replies View RelatedI am installing a network in my small business and was given a spool of Cat5 cable to run wires... I know the length in feet of cable that I was given, but I was wondering if there is some kind of markers on the cable to tell me how much is left... I will be charged for it by foot after I'm done, and I want to know how much I've used. Do I have to just use a measuring tape? Seems unnecessarily complicated... I've checked the wire but can't see any marker of the length remaining.
View 1 Replies View RelatedFeature AIR-CAB020LL-R AIR-CAB050LL-R AIR-CAB100ULL-R AIR-CAB150ULL-R Cable Length 20 ft (6 m)50 ft (15 m)100 ft (30 m)150 ft (46 m) Transmission Loss 1.3 dB3.4 dB4.4 dB6.6 dB for Cisco 1941W router with external antennas?
View 3 Replies View Relatedcan anyone suggest the cable length of CAB-C15-CBN?
View 5 Replies View Relatedwhat length does cat6 cable support for networking
View 3 Replies View Relatedas we know twisted pair cat 5 has maximum length 100 meter?
is because the voltage will decrease"weak" at the receiver "because the resistance of cable"? or because the noise will increase?
what is the maximum length a cat7 cable can work for a backbone
View 2 Replies View RelatedHow much load (DATA) cat-6 cable can handle over a length of 100 meters?
View 2 Replies View RelatedI want to "stack" a couple 300 series gigabit switches with fiber using a pair of MGBSX1 GBICs and a single LC to LC patch cable.Is there a minimum supported patch cable length in this configuration?
View 2 Replies View RelatedWe have the Cisco WRT54G wifi router in many offices in this building. This router has two antennas. These antenna are screw into the back of the router unit. The antenna is male and router side is female of the connector. what are these connectors (some type of RF connectors)? How can we get extension cables for these to move the antenna from one fix location to another point?
View 4 Replies View RelatedI am relocating UPS units and will need to buy longer power cables to extend from our 4506 and 4510 to the new location.I think I am looking at 15 to 20 feet but I am going to confirm. Is it okay to use longer cables?
View 9 Replies View RelatedI set the password for the router management consisting of 115 characters. Now I can not log into the router.
1. What is the maximum length of passwords to manage the WAG320N router?
2. What are valid characters in a password for this router?
I am running a wrt54g and I was woundering what is the longest rj45 cable length I can run?
I notice running about 30 plus feet connection does not work. When I cut off about 5 feet it worked. Seems I can only run a ceratin amount of cable length with this router.
I have a Dlink DIR-655 router for my wired and wireless router for my home network. I have a 100ft cat6 ethernet cable. I pulled it from the router to my home server in my basement.
Does the 100ft cable make a difference or does the fact that it's a cat6 cable make a difference?
When moving similar files at work, it's faster. So I'm trying to find out what's the bottleneck at home. What speeds should I expect for a home network?
I have a Linksys BEFSX41 wired router. If I wanted to connect a second computer to my router, what would be the maximum length of cable I can use without experiencing any problems ?
View 3 Replies View RelatedLet's say, an antenna like that Should I open the modem and therein there could be a slot for it to be plugged in? Because on the back side of the modem none of the slots will suit such plug.
View 2 Replies View RelatedI have a Linksys WAG 120 N wireless router with an internal arial. I want to strengthen the signal to my laptop 2 rooms away as it keeps dropping out. Is it possible to change WAGGING from internal to external antenna to increase range/performance?
View 1 Replies View RelatedI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedI have a modem, 2 wireless routers and 30 foot of ethernet cable,I want to get ( wireless ) internet in to my extension in the garage.I want to run an ethernet cable into the garage and was wondering if i could put a wireless router in there.
View 2 Replies View RelatedI've just installed a Netgear WDR4500 (n900) in my second floor office.The wireless range works great for multiple top floor computers as well as the 1st floor TV/ps3/tablet area.I am having some issue in the backyard and back deck though. (just something about my stucco walls)
So here is my question.I have my old DLINK dir-655. Would it be advisable to use a powerline connection (I already have Powerline adapters) to the ground floor near the back and piggyback the wireless?(This would also allow me to Hardwire the TV/ps3/htpc)
I would just like to know if this will work. I have 2 Linksys wireless routers, 1 is located downstairs, connected to the cable modem and setup wireless, the other is on the second floor on the other side of the house. I need to extend the wireless range but also keep the 2 pcs upstairs connected through the Ethernet cable.
Router A Connected downstairs to modem 192.168.1.1 DHCP enabled (Change scope to leave out the .2) WPA on wireless setup channel 11
Router B Give it a static ip of 192.168.1.2 Connect cable from wall to any LAN port on router
Setup WPA using same SSID and PW different channel . Leave the 2 pc's connected as before.
The other 2 hardwired PCs should get an address from Router A and be able to connect to the internet?Does this make sense and should it work?
Is it possible to convert autonomous access point Cisco 1262 to LAP?
View 9 Replies View RelatedI have a 1262 that will be setup as a WGB and wirelessly connect to a Cisco MESH AP. A switch and clients will hang off of the 1262 WGB. How many clients can a 1262 WGB support?
View 4 Replies View RelatedWe have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies View Related