I have a modem, 2 wireless routers and 30 foot of ethernet cable,I want to get ( wireless ) internet in to my extension in the garage.I want to run an ethernet cable into the garage and was wondering if i could put a wireless router in there.
View 2 RepliesI've just installed a Netgear WDR4500 (n900) in my second floor office.The wireless range works great for multiple top floor computers as well as the 1st floor TV/ps3/tablet area.I am having some issue in the backyard and back deck though. (just something about my stucco walls)
So here is my question.I have my old DLINK dir-655. Would it be advisable to use a powerline connection (I already have Powerline adapters) to the ground floor near the back and piggyback the wireless?(This would also allow me to Hardwire the TV/ps3/htpc)
providing an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
I would just like to know if this will work. I have 2 Linksys wireless routers, 1 is located downstairs, connected to the cable modem and setup wireless, the other is on the second floor on the other side of the house. I need to extend the wireless range but also keep the 2 pcs upstairs connected through the Ethernet cable.
Router A Connected downstairs to modem 192.168.1.1 DHCP enabled (Change scope to leave out the .2) WPA on wireless setup channel 11
Router B Give it a static ip of 192.168.1.2 Connect cable from wall to any LAN port on router
Setup WPA using same SSID and PW different channel . Leave the 2 pc's connected as before.
The other 2 hardwired PCs should get an address from Router A and be able to connect to the internet?Does this make sense and should it work?
I have a WRT54G that has served us well for several years, but I needed a network connection in another part of the house, both wired for TV, and wireless for downstairs. So I ran an ethernet cable through the house and connected it to my new E1200. It's connected to Port 1, not the Internet port. The TV plugs into Port 2, and my Apple TV to port 3. So far so good, TV and Apple TV appear to work fine. Wireless is where I'm having problems, the wireless signals between the two routers appear on Wifi Analyzer I'm using. Both appear strong in signal for a second, then they disappear, then they appear again for a second, then they disappear. So the wifi's signals appear, then disappear and this cycle continues.
The WRT54G is setup with DHCP, channel 6.
IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: Enabled Start IP Address: 192.168.1.100 End IP Address: 192.168.1.149
The E1200 DHCP is disabled, channel 11, 20mhz.
Router IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 DHCP Server: Disabled Start IP Address: 192.168.1.1 (DHCP disabled) End IP Address: 192.168.1.50 (DHCP is disabled)
I've tried both routers named the same, and then tried 2 different names. I've rebooted them as well after making changes.
I want to install some AIR-ANT2566P4W-R antennas outdoor against the wall, the 2602e access points will be mounted on the interior side of the wall, altough the wall is 30cm thick, so I need some antenna extension cables.What type of coax extension cables would be recommended ?
View 1 Replies View Relatedcan i use a cat 5 cable to extend a 9 pin serial cable to connect my PC to my home audio controller? I have a serial to USB converter but my PC is upstairs and my audio component is downstairs?
View 1 Replies View RelatedI'm working with a Cisco Unified CM 7.0There are sevral ip phones in the place.ach phone has a 3 digit extension tied to it. no matter where on the network that phone is plugged in that phone has the same extension. This is a problem because one phone (extension 134) is damaged and was swapped out with a phone that has extension 102. I want that phone that has extension 102 to have the extension 134 instead.So that is my problem. I must say I am merely a CCNA and I have no idea about this voip stuff. I thought it was a simple log in to the server and make a single change. boy was I wrong. I clicked on call routing, then I clicked on Directory number and I got a list of all the DNs. I then click on extension 102 and 134. I noticed the MAC of the respective phones was in a field titled associated devices. I then dissociated both phones thinking I could just associate the appropriate phones next. as soon as I hit save that entire section disappeared. Now those extension aren't tied to any phone and once more those phones now have no extensions. I am freaking out because I can't undo this. I've clicked on literally every single option inside this server. I am in way over my head. I will include a picture to illestrate what I am talking about.
View 6 Replies View RelatedLet's suppose I'm connected to a network whose admin asked in a friendly way not to download anything but certain things he specified.He never came to my machine or setup any kind of client to it. The question now is, is there any chance he knows what I download???Does he know the name and the extension of the file I download if I use Utorrent and magnet links?
View 2 Replies View Relatedi recently bought a wifi adapter capable of 300mbps, as apposed to my old 54mbps adapter, and an active 10m extension.
now the extension does power the adapter, but the cpu doesnt seem to recognize the adapter is plugged in, but if i plug the adapter straight into the computer then it all works fine.
other people seem to have no problem at all doing this to achieve better signal.
[URL]
I have a pbx avaya phone system with lines and extension number.I needed a phone with line and extension.So i run the ethernet cable to the office made all connection and connected ethernet wire directly to the pbx avaya, and i got the phone working with the extension.But my question is to get the line working and the extension i have to punch down the cable from the pbx, the ethernet wire and the pair of wire coming in with the line?
View 7 Replies View RelatedFindout what is the Reason for does not Opening a bin Extension File?
View 1 Replies View RelatedI've recently obtained a Cisco Aironet 1242AG WAP. I do realize this is not a standalone router. I would like to use it as an extension of my current router. So right now, the status light is alternating colors. If I understand this correctly, it cannot find the controller. I cannot telnet into it, or use the web broswer interface. They both say the connection is not available. However, when I check my DHCP table from my router, I see that an IP has been assigned to the MAC for the WAP. I've tried doing a factory reset by holding MODE before I plug in the power, and waiting until it turns amber. After a few minutes and going through a few LED changes, it goes back to continuosly alternating colors.
View 14 Replies View RelatedI have a plug into the mains network, but I need to connect more than one RJ45 cable to it.What is the best way to do this?Also, could I somehow connect a wi-fi extension to the plug in unit?
View 2 Replies View RelatedI have been rolling out new IP Phones that use extension mobility and the biggest issue Im finding is the need to log-in every day, People t like change and they hate the fact that they have to login every day.I have been to the people at the top and gave them the options of remembering the last user logged so users just need to enter their pin or have EM not log users out at all… both got rejected.
View 2 Replies View RelatedDoes the 4500E platform (sup7E) support the extension VLAN over MAN connections? In wich technology?
View 1 Replies View RelatedAny cheap outdoor extension antenna that works with a Linksys wap54g? Not looking for anything too expensive. Just trying to bring wifi signal into a building.
View 1 Replies View RelatedI have a F5D7231-4 router and I would like to know:
1) if it can serve as network extension (wifi)? from main wifi router
2) if I can setup a local network getting ip from my iphone, then using DHCP to have on same network my ipad, and a printer?
In CUCME if you do not configure any translation rules and leave the system mainly at default, when a call is routed to the PSTN the CUCME system sends the true calling party ID which would be a users extension number. Is it correct to assume that a CUCM server based system, when too left at the majority of default (without translation rules or stripping etc) that it will send the true calling ID to the gateway?
View 1 Replies View RelatedAnybody know of a extension cable for this product? D-Link 14dBi Outdoor Direct Antenna (ANT24-1400) I need at least 10-15 feet of extra length.
View 1 Replies View Relatedwe got a dark fiber betwwen two sites away from each other 30 Km,i need to connect this sites acts as backup dc to main dc in main site using cisco 4900 Switches in BK-DC anf 6513 in the main site,how can i verfiy if this fiber oparates as L2 and i can extend vlan servers,is it via "sh cdp neigh" and "sh vlan br"?
View 2 Replies View Relatedi want to download an backup of the configuration file of my Cisco sg300-10 but do not know what to call the file extension.. backup.??? backup.img? backup.ros ?
View 4 Replies View RelatedWe bought a pair of ASR 1004 to be installed at Primar & Secondary data center and one thing is to run OTV over it, but to do that, I have to extend multiple VLANs from my Core (Pair of Nexus 7010s) connected directly to the ASR is Primary Data center, I looked at some documents but didn't get a good idea about it, extend multiple VLANs from Nexus switch to an ASR.
View 2 Replies View RelatedAbout to apply a patch for the first time on the ACS 5.3 tonight. Ihave tftp'd it onto a directory i have created on the server. However my support hints i may havre to rename the file ? copy the latest patch file you got from Cisco – you may need to rename as gpg) Current filename is 5-3-0-40-7.tar.tar
So would i need to rename this as 5-3-0-40-7.tar.gpz . If so i will rename it on my pc and redownload it on tftp
I have a Sony Vaio running Windows 7 Home Premium. Yesterday I accessed the Internet at the office over a Cat5 cable. Last night I accessed the Internet at home via my USB Internet dongle (actually an O2 mobile phone). Today neither works. I have also tried to connect to the Internet via Wireless and that does not work either.Needless to say my desktop (using the same Cat5 cable) works. My mobile phone can access the Internet on it own. And others can get the wireless to work.My Vaio can connect to all three; however, all three say "No Internet access".I changed nothing between last night and this morning. I have scanned through the list of Windows Updates and nothing has been downloaded in the past week. I have turned off my firewalls (in both McAfee and Symantec Endpoint Protection). I have run the three NETSH reset commands with Administrator privileges. I have rebooted my machine numerous times. Nothing works.
View 4 Replies View Relatedwireless internet connection connected no bit it says no internet access what is the problem
View 1 Replies View RelatedWhenever my sister plays on the laptop. My ping goes up to 400+. Is there a way to make my ping less and she could still do w/e she wants on her laptop?
View 1 Replies View Relatedhave a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies View RelatedI have a Panasonic Viera plasma tv (with no Wi-Fi) and as soon as i turn it on my wireless internet drops. It is a d-link 615 with a netgear modem attached. i cant find anything on the internet about it, have even tried changing every channel on the router and still no luck
View 4 Replies View RelatedRecently my wirless internet stopped working. I am running a HP dv 9000 laptop. The indicator light always stays amber (instead of turning blue when turned on) on external wirless switch. The wireless adaptor should be a Broadcom 802.11b. This does not show up in device manager, but my computer says the driver for it is installed. In the device manager there is one device with a yellow question mark beside it called "other device". Under this device there are three more devices called "base system device" with a yellow exclamation point next to them
View 7 Replies View RelatedI'm having an intermittent issue with my E4200v2 router. Frequently I will be using a device on the wireless network, and it will be unable to reach the internet. Normally I would assume this was a problem with the cable modem, but disconnecting from and reconnecting to the router often fixes the problem.
View 9 Replies View RelatedI have one WET200 Wireless Brigde, connected to internet router... I can't use the infraestructure mode to broadcast the ssid to wireless cliente like laptops,
Only can use the ad hoc mode, but the wireless clients dont reach the internet from adhoc connection trought WET200...The datasheet saids "client only" for WET200, what is the diference between client only and Access Point mode? ??
I have wonder that my laptop has wireless, and when i connect it to router to use internet it show wireless now is connect, but when i open the website it show not work..and this problem occur only my computer. and when the other computer laptop they can connect and use internet normal...
View 1 Replies View Related