I have a F5D7231-4 router and I would like to know:
1) if it can serve as network extension (wifi)? from main wifi router
2) if I can setup a local network getting ip from my iphone, then using DHCP to have on same network my ipad, and a printer?
I cannot map a network drive over a VPN. I am asked for login credentials, but no credentials are required, per the IT guy. He says that it's a Port 47 issue. How do I allow traffic via Port 47? Router F5D7231-4
View 1 Replies View RelatedHaving no success with installing a wireless G+ router F5D7231-4, without any accompanying disc etc which I got second hand, neither can I complete Installation of a new Belkin wireless G USB adapter [with disc], keeps saying there's a missing shortcut that cant be found, my PC is Acer Aspire 5551 which has no wireless facility built in, all connected to a Virgin wired modem, is there a quick fix, I'm using windows 7 if that makes any difference,.
View 3 Replies View RelatedI'm trying to activate parental control for the F5D7231-4 (2000). When I go to the parental control screen, I only get a button to subscribe now (see image). When I click the button, I am sent to the Belkin UK website. I cannot find out how to get the parental controls activated on the U.S. site. I am running the latest firmware (F5D7231-4_US_5.01.11 ).
Update: I looked at the source code for the page in the router...it's referencing a website : [URL] that no longer seems to be valid. Or is this a problem in the firmware ?
I have a Belkin High-Speed Mode Wireless G Router F5D7231-4 and I wish to use it as an access point for my main desktop for my wireless network.
I have followed methods supplied by both Belkin and users and have had no success.
Instructions followed:
- Connect a computer to Belkin router using an ethernet cable.
- Reset the router to factory defaults. The reset button can be found at the botton of it. The reset procedure is given below
- Make sure the router is switched ON.
- Locate the reset button(inside a hole) at the back of the router.
- Use a paper clip, push the reset button and hold it for 30 seconds then release the reset button.
- Unplug the Power cable from back of the router and plug it back again and wait for another 30 seconds.
- Log on to router setup page by typing 192.168.2.1 in the address bar of the browser.
- On the left under wireless click on the option Use as Access Point.
- Select Enable and specify the IP address as 192.168.2.254 and subnet mask as 255.255.255.0 and click on apply changes.
Every time the system crashes whilst applying the changes.
Can I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies View Relatedi recently bought a wifi adapter capable of 300mbps, as apposed to my old 54mbps adapter, and an active 10m extension.
now the extension does power the adapter, but the cpu doesnt seem to recognize the adapter is plugged in, but if i plug the adapter straight into the computer then it all works fine.
other people seem to have no problem at all doing this to achieve better signal.
[URL]
I have a plug into the mains network, but I need to connect more than one RJ45 cable to it.What is the best way to do this?Also, could I somehow connect a wi-fi extension to the plug in unit?
View 2 Replies View RelatedHow do set a wifi password? Have been operating for years without a wifi password but now I want one.
Have an N1 wireless, F5D8231-4 Router setup, 192.168.2.1
How can I set up a N150 router so that I can access a WiFi printer (Canon) with my laptop and/or iOS device? No Internet involved - just want to wirelessly print to my new Canon printer.
View 1 Replies View RelatedI'm attempting to connect a 2nd wifi router to my belkin f5d9230-4.
View 1 Replies View RelatedCan I connect a Belkin N450 wireless router to a Belkin N750 wireless router without using a cat5e cable?
View 1 Replies View RelatedFor some reason, wireless connections from my moms Belkin Play router #F7D4302 v1 disconnect everytime the landline phone is used! There is no phone line connected to my moms computer, modem or router
View 3 Replies View RelatedJust bought a samsung galaxy s4 and I haven't been able to get my WiFi to work with my Belkin router (Surf N300 wireless router, model F7D6301). I tried giving it a static IP and got it to connect to the network, but it still wasn't able to leverage the WiFi for use.The router firmware is up to date.
View 4 Replies View RelatedWe added a Belkin N750DB wireless to our building yesterday. Everyone is working fine except one computer that is an apple. Her wi-fi keeps going on and off. Is there a setting we need to change so this stops happening and she has constant internet?
View 1 Replies View RelatedMy N150 wireless router sees 25mb+ speed from my internet connection but my wireless connects at 1mb. Why is the WiFi being resricted?
View 2 Replies View RelatedCan N600 DB Wi-Fi Range Extender have the exact same name as my N600 DB Router or does the extender have to have the additional characters "_xt" at the end of the extender name, when the first part matches the router name?
View 1 Replies View RelatedWhen i try to enter the password for my N300 Belkin Router into my wifi connection setup in my computer it will not accept any letters, only numbers.
View 1 Replies View RelatedWhy does my HP Photosmart B110 printer not work wirelessly through my new Belkin Surf N300 modem router? Everything is fine using my old Philips CONN-X router.Is bonjour connectivity the issue? All my other devices work fine connected through the Belkin wi-fi.
View 2 Replies View RelatedI have a ADSL modem with a wi-fi router connected to the internet. I want to connect my Belkin F5D8233-4v3 to the router wirelessly and use it as an Access Point to extend the range of my home wi-fi setup. How do I configure the Belkin to connect to the adsl router over wi-fi without running the cable?
View 1 Replies View Relatedgot the ac900db router set up and the the setup page to allow me to set security is no longer available and i am now unprotected with my wi-fi for a guest login.....website for belkin is a viscious loop that explains NOTHING at all and has no easy way to find how to fix anything!! how do i get to the DASHBOARD or even log back into my account i set up?
View 1 Replies View RelatedIs there a way to quickly disable Wi-Fi on a N-150 from the router setup page? I have looked on my admin page but I don't see it. I just want to be able to turn the radio on and off from the PC that is connected via ethernet.
View 3 Replies View RelatedOn Page 16 of my N600 DB manual it says that below the "Router Status Light" and above the "WPS" letters there is a "Wi-Fi Protected Setup (WPS) Light and Button". When I look at my router all I see in this space is a raised rectangular plastic strip. Should I have a light and button there?
View 1 Replies View RelatedI am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies View RelatedI just updated my F5D8233-4 ver 3000 router with the latest firmware. Now only one of the hardwired ports works (#1) and it causes the router trouble enough sometimes to make it disconnect from the cable modem. All the wifi connections (5 of them) work well and do not appear to cause any trouble. What can I do?
View 1 Replies View RelatedI have a WRT54G that has served us well for several years, but I needed a network connection in another part of the house, both wired for TV, and wireless for downstairs. So I ran an ethernet cable through the house and connected it to my new E1200. It's connected to Port 1, not the Internet port. The TV plugs into Port 2, and my Apple TV to port 3. So far so good, TV and Apple TV appear to work fine. Wireless is where I'm having problems, the wireless signals between the two routers appear on Wifi Analyzer I'm using. Both appear strong in signal for a second, then they disappear, then they appear again for a second, then they disappear. So the wifi's signals appear, then disappear and this cycle continues.
The WRT54G is setup with DHCP, channel 6.
IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: Enabled Start IP Address: 192.168.1.100 End IP Address: 192.168.1.149
The E1200 DHCP is disabled, channel 11, 20mhz.
Router IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 DHCP Server: Disabled Start IP Address: 192.168.1.1 (DHCP disabled) End IP Address: 192.168.1.50 (DHCP is disabled)
I've tried both routers named the same, and then tried 2 different names. I've rebooted them as well after making changes.
I just bought an N750. Setup was ok once my modem was recognized. How do I change the name of my network now that the router is installed and working?
View 2 Replies View RelatedI used to be able to connect to the 5g network on my D600 router, but now I cannot. I'm literally 6 feet away from my router and have not changed any settings.
View 1 Replies View RelatedI'm having a problem connecting with wireless card model number f9L1101v1 to a router model number F5D7234-4. the computer is dell dimensions 4400 desktop pc running windows xp, everything seems to be working correctly. i can see my wireless connection, signal strength is full, but when i enter the network key which i have confirmed is correct it will not connect. it goes to the window where it shows it trying to connect but after about 2 minutes the window disappears with no explanation for connection failure.the network key was confirmed through a laptop that runs on the same router.
View 2 Replies View RelatedI've just hooked up my previously used N300 router. The router is showing a solid green light, and the laptop recognizes that a solid Belkin wireless connection is out there. I cannot for the life of me remember the network key and/ or pass phrase I originally set. No, I did not tape this info to the underside of the router as suggested in Belkin instructions.
View 6 Replies View RelatedNo light on adaptor, not recogised in device manager. Worked before PSU failed.
View 1 Replies View RelatedMy ISP is Comcast and I own a Belkin N750 DBWireless N+ Router, I have a Synology NAS drive wired to the router. I am trying to set up the network configuration on the NAS drive so I can have internet access to the drive. My question is do I manually define the IP address, subnet mask, DNS, and gateway or do I select DHCP. If so what addresses should I use the address of the NAS drive form the router or the router address. I think I need to use the manual fields and use a static IP but do I get that IP address from the router or from my ISP (comcast)?
View 2 Replies View RelatedNetwork hub, model f5l009 not registering as a connected network USB Hub. Therefore, unable to update firmware. Devices connected to HUB are of course also not showing up. Reinstalled drivers. PC Windows 7 home pro on Comcast and a Cisco router. Firewalls are set to "allow". Only change in system is from internet providers to "Comcast". What might be causing the problem? Tried connecting directly to the Comcast router and that didn't work. Tried a hard reset on the HUB and that didn't work. If this device has failed is there a way to replace it?
View 1 Replies View Related