Belkin Routers :: F5d7231-4 - No Success In Installation
Feb 21, 2013
Having no success with installing a wireless G+ router F5D7231-4, without any accompanying disc etc which I got second hand, neither can I complete Installation of a new Belkin wireless G USB adapter [with disc], keeps saying there's a missing shortcut that cant be found, my PC is Acer Aspire 5551 which has no wireless facility built in, all connected to a Virgin wired modem, is there a quick fix, I'm using windows 7 if that makes any difference,.
View 3 Replies
ADVERTISEMENT
Nov 27, 2012
I cannot map a network drive over a VPN. I am asked for login credentials, but no credentials are required, per the IT guy. He says that it's a Port 47 issue. How do I allow traffic via Port 47? Router F5D7231-4
View 1 Replies
View Related
Apr 13, 2013
I have a F5D7231-4 router and I would like to know:
1) if it can serve as network extension (wifi)? from main wifi router
2) if I can setup a local network getting ip from my iphone, then using DHCP to have on same network my ipad, and a printer?
View 2 Replies
View Related
Oct 28, 2012
I'm trying to activate parental control for the F5D7231-4 (2000). When I go to the parental control screen, I only get a button to subscribe now (see image). When I click the button, I am sent to the Belkin UK website. I cannot find out how to get the parental controls activated on the U.S. site. I am running the latest firmware (F5D7231-4_US_5.01.11 ).
Update: I looked at the source code for the page in the router...it's referencing a website : [URL] that no longer seems to be valid. Or is this a problem in the firmware ?
View 2 Replies
View Related
Aug 3, 2011
I have a Belkin High-Speed Mode Wireless G Router F5D7231-4 and I wish to use it as an access point for my main desktop for my wireless network.
I have followed methods supplied by both Belkin and users and have had no success.
Instructions followed:
- Connect a computer to Belkin router using an ethernet cable.
- Reset the router to factory defaults. The reset button can be found at the botton of it. The reset procedure is given below
- Make sure the router is switched ON.
- Locate the reset button(inside a hole) at the back of the router.
- Use a paper clip, push the reset button and hold it for 30 seconds then release the reset button.
- Unplug the Power cable from back of the router and plug it back again and wait for another 30 seconds.
- Log on to router setup page by typing 192.168.2.1 in the address bar of the browser.
- On the left under wireless click on the option Use as Access Point.
- Select Enable and specify the IP address as 192.168.2.254 and subnet mask as 255.255.255.0 and click on apply changes.
Every time the system crashes whilst applying the changes.
View 4 Replies
View Related
Oct 20, 2012
I lost my set up CD for my N150 Belkin router is there a way to manually download the driver installation?
View 3 Replies
View Related
May 8, 2013
i lost my belkin n150 installation cd, and i haven't installed it on my computer, my net connection to my computer via lan keeps dying, but wi-fi works perfectly. What should i do? Where can i download the software from??
View 1 Replies
View Related
Oct 3, 2011
I have a dell Win XP need to connect to Belkin router
View 1 Replies
View Related
Aug 15, 2011
When I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
View 1 Replies
View Related
Apr 26, 2013
(F5D9230-4 v5111 Belkin mimo router ) is version 5.02.08 the most up to date firmware for my router?
View 1 Replies
View Related
Apr 26, 2013
How do I setup my Belkin F7D1301 with a 16 port 10/100 switch so I can use the wireless on the Belkin and have the 16 port switch for my hard wires?
View 1 Replies
View Related
Jun 2, 2012
I try to use fe0 as outside, with dhcp from my ISP, and fe1-fe3 as inside on my Cisco 877. I have done this successfully before but now it just will not work. This has been a long weekend .
My ISP just forced DHCP on me (from static IP) and sent me this Xavi adsl modem. I successfully get IP addresses using DHCP from it with workstations, but not with my cisco. With current setup I get DHCP errors (DHCP: QScan: Timed out Selecting state%Unknown DHCP problem.). DHCP log is attached.
Setup is attached too, but the main parts are:
-----------------------
interface FastEthernet0
switchport access vlan 2
!
[Code]......
View 16 Replies
View Related
Sep 25, 2012
I am getting some weir behaviour in my LMS 4.2 setup. I am doing and Archiveupdate job and am receiving a partial success for roughly 1400 devices. Here is some output.
Execution Result:
STARTUP
CM0057 PRIMARY STARTUP Config fetch SUCCESS, archival failed for
xxxxxx Cause: CM0210 Unable to generate
processed config Action: Verify that archive exists for device.
RUNNING
[code]...
I went on and checked the dcmaservice log file.I found the following entry at the same time of this particulair job
ERROR,[Thread-72920],com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.analyzer.IOSConfigletRules,loadRules,42,Could not locate configlet rule file : com/cisco/nm/xms/xdi/pkgs/SharedDcmaIOS/analyzer/IOSConfigletRules.ser
[ date taken out ],ERROR,[Thread-72920],com.cisco.nm.rmeng.dcma.configmanager.DeviceArchiveManager,archiveNewVersionIfNeeded,1115,CM0210 Unable to generate processed config
I then searched if I had the IOSConfigletRules.set file on the box. And no it is not there. My question is this the reasson that I have som manny partial sucess archive results?
View 2 Replies
View Related
Apr 17, 2013
I am interested to configure my slingbox with my ASA5505. I am currently able to use the device remotely when I connect via VPN. My concern is that the VPN uses too much bandwith and I would get better quality if I would able to forward the appropirate ports through the ASA5505 and connect directly from the outside.
View 1 Replies
View Related
Jan 6, 2012
I just installed a DIR-601 cascaded with a WiFi G Netgear router. The D-Link is handling DHCP. I am having varying degrees of success with the WiFi signal. One XP laptop gets anything between 80Mbps and 150Mbps (can change while sitting in the same location), while another Win7 netbook does slightly worse. My Son's MacBook Pro never seems to do any better than 72Mbps.
I dedicated the D-Link to 802.11N and only allow these 3 devices to connect to it as N devices. All other WiFi devices are G and use the Netgear G router. I am using WPA2-Personal/AES and Auto bandwidth (40 does not seem to be a choice).Didn't experience such performance fluctuations with the Netgear G router.
View 14 Replies
View Related
Nov 28, 2010
WLC 5508: software version 7.0.98.0
Windows 7 Client
Radius Server: Fedora Core 13 / Freeradius with LDAP storage backend
I have followed the guide at URL with respective to building the LDAP and free radius server. 802.1x authorization and authenication correctly work. The session keys are returned from the radius server and the wlc send the appropriate information for the client to generate the WEP key.
However, the WLC does not override the VLAN assignment, even though I was to believe I set everything up correctly. From the packet capture, you can see that verfication of client is authorized to use the WLAN returns the needed attributes:
AVP: l=4 t=Tunnel-Private-Group-Id(81): 10
AVP: l=6 t=Tunnel-Medium-Type(65): IEEE-802(6)
AVP: l=6 t=Tunnel-Type(64): VLAN(13)
View 8 Replies
View Related
Jan 6, 2013
Using ISE 1.1.1 and Switch 3650 12.2(55)SE6. I have a client (computer) that should be authenticated with MAB and then the switch port should be asigned a DACL and VLAN 90. I do get "Authorization succeeded" but directly after it fails and I can't figure out why. ISE only shows the successful authentication under "Live Authentications".
As you can se from the log below 802.1x fails, as it should, and then MAB succeed, asigns the VLAN and then fails:
0002SWC002(config)#int fa0/13
0002SWC002(config-if)#shut
0002SWC002(config-if)#
[Code]....
View 11 Replies
View Related
Jan 2, 2013
If your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
View 6 Replies
View Related
Apr 8, 2011
We are trying to isolate the fault. From Aggregator a router, we are receiving MAC address of distant end ethernet interface of a SDH box and vice versa is also possible. However ther is no packet received. My question is does ping test is must to see if the path is through or just receiving MAC adress at both ends would mean that packets have to go over the path.
View 1 Replies
View Related
Jan 21, 2012
I purchased an E2500 wireless router. I am trying to replace a Netgear wilreless router with no success. During installation my laptop reaches about 25% and I get an error message. In short my laptop asks for an IP address with a password. Once I enter that information I receive an error message to call for assistance.
View 1 Replies
View Related
Apr 18, 2011
I'm trying to join a band new CSACS-1120 to our active directory without success. The process in it self should be pretty straigh forward, but so far no luck.
I've configured the relevant info under "Users and Identity Stores > External Identity Stores > Active Directory.
Active Directory Domain Name: xxx.com
Username/Password : domain administrator account
When I test connection I get a info dialog "This machine is currently connected to domain xxx.com".After which I try to save changes which gives a reply ""This System Failure occurred: {0}. Your changes have not been saved. Click OK to return to the list page."
I've noticed that in the system log "show logging system tail" that I get a exception as soon as I enter the AD configuration page and subsequently every time I perform a action on that section.
Why the AD join keeps on failing and what the debug exception I'm getting means?
View 3 Replies
View Related
Mar 21, 2013
I have the N600DB Wireless Router I am connected to the internet, but cannot open My Routers Homepage with http://router or http://192.168.2.1. How can I get to this page to reset the router settings? I also cannot connect any of my wireless devices to the network..
View 1 Replies
View Related
Dec 29, 2012
I have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies
View Related
Jul 10, 2011
I just installed WRT54GH and wireless was working fine, after almost 3 hours passed I lost connection with it.I tried to connect using wireless with 3 different notebooks without success. Just using cable it works.I upgraded firmware from v1.0.010 to v1.0.01 but still not working.
View 7 Replies
View Related
Jan 3, 2012
I have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies
View Related
Nov 24, 2011
I try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 Replies
View Related
Jul 9, 2012
In my house...I have one router upstairs (Belkin F5D8236-4) and great signal upstairs...downstairs signal is not so swift and sometimes, I can't even get a signal. So I thought let me go purchase a router (router # 2) and set it up downstairs and see if that will improve the signal of my Belkin. The 2nd router I purchased is a Belkin N150 (I thought buy 2 Belkins...maybe they can communicate better?). What I need to know is how do I connect the Belkin N150, to my Belkin F5.. and just use it to strengthen my signal to my downstairs part of the house?
View 14 Replies
View Related
Oct 18, 2012
I see the switch to toggle the QOS on and off, but it is greyed out in on and will not allow me to switch. I would like to see if it solves the speed problem with my iPad. The newest firmware is installed in the router. I also tried changing other fields to see if it would unlock the quality of service field with no luck.
View 13 Replies
View Related
Jan 11, 2013
Lately I notice my router is very very slow. most of the time I cannot use my ipad or it takes too long and sometimes never finishes downloading a web site. I called Belkin support, and I was told that I need to update and configure, and to do that I have to pay more than what my router cost.
View 3 Replies
View Related
Oct 17, 2012
under support I cannot access any info for a f80 router. Nothing allows me to enter that model #.
View 1 Replies
View Related
Apr 17, 2013
I was trying for hours to connect the USB Hard Drive of 3TB (My Book WD 3TB) in the USB port A and B of the router then the router won't reconize. I Have another the same model but different capacity and work excellent (My Book WD 2TB). What I can I do in order to use my hard drive in my network?
View 2 Replies
View Related
Dec 12, 2012
N600 router will not comunicate with my desktop computer through a cisco switch. The LAN was working fine when I was using a Linksys router. Is this a compatability problem between Belkin and Linksys products?
View 1 Replies
View Related
Jan 21, 2013
Does the Blekin N1 Vision have a WPS button? I'm trying to add an extender.
View 1 Replies
View Related
