I am interested to configure my slingbox with my ASA5505. I am currently able to use the device remotely when I connect via VPN. My concern is that the VPN uses too much bandwith and I would get better quality if I would able to forward the appropirate ports through the ASA5505 and connect directly from the outside.
View 1 Replies
I'm trying to configure an ASA 5505 to view my Slingbox from my iPhone/iPad from an outside or 3G network. I can't ping my internal networks while connected via AnyConnect. I know that I need to free up port 5001, but I can't seem to get it to work.
View 0 Replies View RelatedI have installed a DIR-655 and it all works at home, my brother accesses my slingbox to get his fix of english tv. This has all worked no problem in the past with the old box (Technicolor TG582n). However it now only connects for approx 5 mins and then it loses the connection. Replacing the old box all is well so it has to be something on the router. I have changed various settings inc changing the MTU size, pointing the gateway to the external gateway address, upgrading the firmware (now on Hardware Version B1, Firmware Version 2.05).
View 3 Replies View RelatedThey have a main Verizon router in their bedroom, which is hard wired to a wireless router in the TV room. The have another cable router (not wireless) and it can receive a signal when you plug an Ethernet cable from output #1 on the wireless router to Internet input on the cable router (the Internet light lights up, meaning it's receiving the signal). Also the wireless router light for output #1 lights up (meaning it's outputting a signal correctly). But, when I plug the same cord into the Slingbox PRO, the network light, on the Slingbox PRO, doesn't light up, nor does the #1 light on the wireless router. The Slingbox is out of warranty.
View 19 Replies View RelatedI just received a Dish TV slingbox and I am trying to set it up to work with my E2500 wireless router.I'm told by Dish that I need to open up ports 80, 443 and 5678. I have Comcast as my ISP.I've gone into the Single Port Forwarding option in the Router Browser interface and for each of the 3 above listed ports have enter this info (using 80 as an example):
External Port: 80
Internal Port: 80
Protocol: Both
To IP Address 192.168.1.2
Enabled is checked
I have confirmed that UPnP is enabled. I am running firmware 1.0.07.I have seen examples on the web where the last digit of the "To IP Address" is left blank, but that is not an option, as I'm forced to enter a number between 1 and 254. 1 will not work as it is my router's IP Address.
I just purchased a new E2500 and I am unable to setup internet viewing with it. I have went in and done the port forwarding and still I have not had any success.
View 1 Replies View RelatedI try to use fe0 as outside, with dhcp from my ISP, and fe1-fe3 as inside on my Cisco 877. I have done this successfully before but now it just will not work. This has been a long weekend .
My ISP just forced DHCP on me (from static IP) and sent me this Xavi adsl modem. I successfully get IP addresses using DHCP from it with workstations, but not with my cisco. With current setup I get DHCP errors (DHCP: QScan: Timed out Selecting state%Unknown DHCP problem.). DHCP log is attached.
Setup is attached too, but the main parts are:
-----------------------
interface FastEthernet0
switchport access vlan 2
!
[Code]......
I cannot establish a local connection between my new WRT54G2 v1 and my Slingbox Classic. I have reset the Slingbox to factory default settings and run the Sling setup wizard but keep getting told that "No Slingoxes Exist on network". The link light is on on both the router and the Slingbox. Slingbox does not show up in the DHCP host table.
View 4 Replies View RelatedSlingbox no longer uses software, but is now web based. I got a new computer and when I go to the site it can't locate my slingbox on their network.
When I go to the site and sign in, it loads the application but then scolls as it looks for my box on the network until it times out. Slingbox directory shows my slingbox, but it says unconfigured.
I called tech support, where I was told my 90 days for free support had expired 2 weeks ago. The port forwarding instructions I found on the internet made references to going into the router and selecting port range forwarding and have start and end port of 5100 and then enable that port.
When I go to support on the slingmedia page, it displays my slingbox with Slingbox status alert, software warning. Instructions state go to slingmedia site and look for update, but if my box is not on thier directory, I can't download update.
Slingbox Info
Slingbox Name: My SlingboxSlingbox ID:XXXXXXXXXXXXXXXXXXXXXXXXX9B30Slingbox Software Version: 1.2.18
Internet Viewing
Set Up Complete: YesSlingbox Public IP Address: XX.XXX.X.228Slingbox Private IP Address: XXX.XXX.X.237Slingbox Port: 5001
Slingbox Access Info
Activation Date: 11-09-2007Date Last Accessed: 02-08-2009
I have a new E4200 with the latest firmware and my slingbox seems to not be playing nice with the router. It refuses to take the IP I reserved for the SB, but always defaults to 192.168.2.254. I use a 2 subnet just in case you're wondering. I have tried multiple reboots and the IP does not change. I have tried turning off UPNP, figuring that was hijacking the dhcp server, but that hasn't changed anything. I also notice that a few of my connected devices do not show up in the dhcp list, yet they connect and work ok.
View 2 Replies View RelatedI am getting some weir behaviour in my LMS 4.2 setup. I am doing and Archiveupdate job and am receiving a partial success for roughly 1400 devices. Here is some output.
Execution Result:
STARTUP
CM0057 PRIMARY STARTUP Config fetch SUCCESS, archival failed for
xxxxxx Cause: CM0210 Unable to generate
processed config Action: Verify that archive exists for device.
RUNNING
[code]...
I went on and checked the dcmaservice log file.I found the following entry at the same time of this particulair job
ERROR,[Thread-72920],com.cisco.nm.xms.xdi.pkgs.SharedDcmaIOS.analyzer.IOSConfigletRules,loadRules,42,Could not locate configlet rule file : com/cisco/nm/xms/xdi/pkgs/SharedDcmaIOS/analyzer/IOSConfigletRules.ser
[ date taken out ],ERROR,[Thread-72920],com.cisco.nm.rmeng.dcma.configmanager.DeviceArchiveManager,archiveNewVersionIfNeeded,1115,CM0210 Unable to generate processed config
I then searched if I had the IOSConfigletRules.set file on the box. And no it is not there. My question is this the reasson that I have som manny partial sucess archive results?
WLC 5508: software version 7.0.98.0
Windows 7 Client
Radius Server: Fedora Core 13 / Freeradius with LDAP storage backend
I have followed the guide at URL with respective to building the LDAP and free radius server. 802.1x authorization and authenication correctly work. The session keys are returned from the radius server and the wlc send the appropriate information for the client to generate the WEP key.
However, the WLC does not override the VLAN assignment, even though I was to believe I set everything up correctly. From the packet capture, you can see that verfication of client is authorized to use the WLAN returns the needed attributes:
AVP: l=4 t=Tunnel-Private-Group-Id(81): 10
AVP: l=6 t=Tunnel-Medium-Type(65): IEEE-802(6)
AVP: l=6 t=Tunnel-Type(64): VLAN(13)
Using ISE 1.1.1 and Switch 3650 12.2(55)SE6. I have a client (computer) that should be authenticated with MAB and then the switch port should be asigned a DACL and VLAN 90. I do get "Authorization succeeded" but directly after it fails and I can't figure out why. ISE only shows the successful authentication under "Live Authentications".
As you can se from the log below 802.1x fails, as it should, and then MAB succeed, asigns the VLAN and then fails:
0002SWC002(config)#int fa0/13
0002SWC002(config-if)#shut
0002SWC002(config-if)#
[Code]....
Having no success with installing a wireless G+ router F5D7231-4, without any accompanying disc etc which I got second hand, neither can I complete Installation of a new Belkin wireless G USB adapter [with disc], keeps saying there's a missing shortcut that cant be found, my PC is Acer Aspire 5551 which has no wireless facility built in, all connected to a Virgin wired modem, is there a quick fix, I'm using windows 7 if that makes any difference,.
View 3 Replies View RelatedI'm trying to join a band new CSACS-1120 to our active directory without success. The process in it self should be pretty straigh forward, but so far no luck.
I've configured the relevant info under "Users and Identity Stores > External Identity Stores > Active Directory.
Active Directory Domain Name: xxx.com
Username/Password : domain administrator account
When I test connection I get a info dialog "This machine is currently connected to domain xxx.com".After which I try to save changes which gives a reply ""This System Failure occurred: {0}. Your changes have not been saved. Click OK to return to the list page."
I've noticed that in the system log "show logging system tail" that I get a exception as soon as I enter the AD configuration page and subsequently every time I perform a action on that section.
Why the AD join keeps on failing and what the debug exception I'm getting means?
I just installed a DIR-601 cascaded with a WiFi G Netgear router. The D-Link is handling DHCP. I am having varying degrees of success with the WiFi signal. One XP laptop gets anything between 80Mbps and 150Mbps (can change while sitting in the same location), while another Win7 netbook does slightly worse. My Son's MacBook Pro never seems to do any better than 72Mbps.
I dedicated the D-Link to 802.11N and only allow these 3 devices to connect to it as N devices. All other WiFi devices are G and use the Netgear G router. I am using WPA2-Personal/AES and Auto bandwidth (40 does not seem to be a choice).Didn't experience such performance fluctuations with the Netgear G router.
I have a cisco 870 router which I'm trying to connect to my ISP all the interfaces are in a up, up state. But I'm unable to ping any IP address on the internet. When I do a debug ppp I can see that the username and password are correct with the dialer 1 interface as there is no errors and I can see success. But when I shutdown the atm0 interface and then do a no shutdown I see a message called authentication failed.How does the atm0 interface work with the dialer,Also I spoke to the ISP and they can't see any connection being made but the debug shows success. I also get a default gateway via the ISP but it is the incorrect default gateway as I can't ping the internet and the ISP confirms that the default gateway is incorrect.
View 33 Replies View RelatedI try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 Replies View RelatedWe are trying to isolate the fault. From Aggregator a router, we are receiving MAC address of distant end ethernet interface of a SDH box and vice versa is also possible. However ther is no packet received. My question is does ping test is must to see if the path is through or just receiving MAC adress at both ends would mean that packets have to go over the path.
View 1 Replies View RelatedI purchased an E2500 wireless router. I am trying to replace a Netgear wilreless router with no success. During installation my laptop reaches about 25% and I get an error message. In short my laptop asks for an IP address with a password. Once I enter that information I receive an error message to call for assistance.
View 1 Replies View RelatedI just installed WRT54GH and wireless was working fine, after almost 3 hours passed I lost connection with it.I tried to connect using wireless with 3 different notebooks without success. Just using cable it works.I upgraded firmware from v1.0.010 to v1.0.01 but still not working.
View 7 Replies View RelatedHow I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View Relatedsetting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:
Network Address Network Mask BTnet NTE Router LAN Address
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
Trying to set up a asa 5505 in transparent firewall mode. I cannot set the management ip address:
ciscoasa> enable
Password:
ciscoasa# config term
[Code].....
I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???
View 4 Replies View RelatedI have a cisco asa 5505 firewall. Is it possible to block secure websites in it like [URL]? I have already tried regular expression filtering but it filters only http traffic.
View 4 Replies View RelatedI am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
Here is our current confguration:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp
[code]....
New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
-Single static public IP: 16.2.3.4
-Need to PAT several ports to three separate servers behind firewall
-One server houses email, pptp server, ftp server and web services: 10.1.20.91
-One server houses drac management (port 445): 10.1.20.92
-One server is the IP phone server using a range of ports: 10.1.20.156
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505. Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP? [code]
I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.
View 1 Replies View RelatedWhen I ping an address from my windows machine, it succeeds, but when I ping to the same IP on my MAC OS X machine, it fails.
1. Why?
2. How to get successful ping on my MAC machine?
