Cabling / Cards :: Slingbox PRO Not Receiving Ethernet Signal
Oct 8, 2011
They have a main Verizon router in their bedroom, which is hard wired to a wireless router in the TV room. The have another cable router (not wireless) and it can receive a signal when you plug an Ethernet cable from output #1 on the wireless router to Internet input on the cable router (the Internet light lights up, meaning it's receiving the signal). Also the wireless router light for output #1 lights up (meaning it's outputting a signal correctly). But, when I plug the same cord into the Slingbox PRO, the network light, on the Slingbox PRO, doesn't light up, nor does the #1 light on the wireless router. The Slingbox is out of warranty.
View 19 Replies
ADVERTISEMENT
Nov 20, 2011
I've been having the same issue. I'll start my laptop and it will start connecting to my home network (comcast docsis 3.0 modem to dlink dir 655 router) and be cool upstairs next to the router, but when I move downstairs the speed jumps down from 130 to 117 to 78 to 5.5 mbps. Its holding steady at 117mbps right now. I'm thinking of upgrading my router to a DIR 827 hd media router 2000 so I can get dual coverage and less interference.
View 1 Replies
View Related
Jan 24, 2012
I have a pci wireless card that I have been using with the same router for some time. All of a sudden in the last couple of weeks it suddenly developed some habbit of dropping the signal from the router on random intervals. During the times that it does it, it will do it over and over again for hours sometimes.It will connect, then drop off less than a minute later, then reconnect again. It will just suddenly say "No Connections available",when normally there are at least 3 connections displayed in the list(2 neighbors and 1 mine).
I am using Windows 7 64 bit and I just now did a fresh reformat on the hard drive an hour or so ago to try and rule out the option of conflicting software/drivers/malware and so on. The problem seems to be persisting still.I have the latest drivers that I can find for my card and updated firmware on the router(same exact setup I have always used).
View 1 Replies
View Related
Mar 5, 2012
I was having a cleanup of the desk and unplugged the cable shortly, and after plugging it back in it could no longer find any connection. The only way I seem to be able to get connected to the internet now is to run a cable to my ethernet switch, and then onwards to my computer itself. Even when doing this the net seems to be very slow, won't connect through Chrome etc or just flat out won't connect.
View 5 Replies
View Related
Apr 10, 2012
I'm going to be upgrading my network (router and network cards etc). I was wondering if there will be any performance difference with the Belkin Fastcat 5e I currently have and CAT6 cables?
View 7 Replies
View Related
Sep 7, 2011
I'm having an issue with my network adapter. It's not detecting the Ethernet cable, thus not able to connect to my home network. The trouble shooter (Windows 7 home 64) says it canning detect the cord. But the cable works fine on my other computer. The network adapter is a Nvdia nforce networking controller. All the drivers are up to date. The computer was completely formatted so it's a blank slate
View 8 Replies
View Related
Apr 3, 2012
I can connect to the internet using my neighbors wireless router but when I try to use my ethernet cable it connects me to "network 16" but the internet doesnt work. Ive tried different cables and different wall ports and that didnt work. It has been working before but I disconnected it to go somewhere and when I came back I had this problem. I use Windows 7 and Im trying to connect using Marvell Yukon 88E8057 PCI-E Gigabit Ethernet Controller.
View 8 Replies
View Related
Sep 13, 2011
Well I did something stupid (big surprise) and somehow managed to uninstall something related to the ethernet ports. I get code 28 and a yellow question mark with a little yellow circle with a black,Anyways what do I need to do to fix this, attached details from everest. It's probably something as simple as reinstalling the drivers, but buggered if I can figure out which ones I need.
View 1 Replies
View Related
Jul 24, 2011
i reformatted my computer 1 month ago, when i try to connect with ethernet cable it doesn't connect, but when i use the usb cable which i got with my modem it connects.btw i have a acer e389 which runs on XP(media center).
View 9 Replies
View Related
Jul 14, 2011
I live in a frat and I am currently researching how to design and configure the most efficient network for the house. However, one of the other big problems we have is connectivity of our ethernet cables. We have an IT room with 2 switches that feed ethernet cables to all parts of the house and connect to an ethernet box in the wall where we can simply wire in our internet connection. We have wireless routers too but to keep the bandwidth usage across the WAP's I want to let people use the wired connections. However, many of the connection in the house do not work at all. I plug in my laptop to the wall jack and it gives me the No Internet Access notice. I don't understand why it works in some rooms and not others. All jacks seem to go into the same switches at the other end so I cannot figure out what the problem could be.
View 2 Replies
View Related
Dec 12, 2012
Ive been using an Ethernet cable to connect to the Internet for a while now, it was working fine up to yesterday where I left my desktop open for a few hours and came back to find that I have no Internet connection.
I used my laptop to test the cable out and it works fine, the wireless works fine too. There doesnt seem to be anything wrong with the modem since I still have Internet on the PS3. I used a different cable to test the modem again with my laptop and I had internet access. The desktop is still connected to the modem but it only gives me a network connection with no Internet.
I tried restarting the modem but it still wouldnt work and I also tried to disable then enable the connection.
Im using Realtek PCIe GBE Family Controller with the latest driver.
View 16 Replies
View Related
Apr 12, 2011
Can't log on to computer running win xp sp3. I'm getting message that ethernet cable is unplugged but it's not unplugged. The modem/router was installed by Verizon (for FIOS connection) in February 2011. Internet was working fine until a couple of days ago. I have looked at other posts on this issue but have found nothing that would solve the problem. My old dial-up modem was still installed in the computer and had a question mark on it in device manager so I removed it. I thought maybe there was an IRQ conflict as the modem used to use IRQ 11 and the network card (linksys) uses that sometimes as well as IRQ 10 but that didn't work.
View 19 Replies
View Related
Jul 12, 2011
One of our ethernet CAT5e is cut off (broken). Now I want to join them instead of putting new cable and doing thing all over again as it is too long.
View 2 Replies
View Related
Aug 3, 2012
Computer keeps saying that the I need to plug in a ethernet cable but I already did. This is happening on my Windows 7 Ultimate partition. I also have have a Mac OSX partition and the internet is working fine on that partition.Here is what I get for ipconfig/all command:[CODE]
View 18 Replies
View Related
Sep 12, 2011
I am having a problem where I can't connect through a cable. I running on Windows XP SP2. My comp. is a HP Pavilion a1483w. I have just reformatted it.
View 3 Replies
View Related
Oct 4, 2011
I have a acer aspire 2930z laptop. My uncle bought it a couple of weeks ago and I finally got my hands on it. But I found out that its internet is not working. When I connect it to my wifi it works fine. But when I cpnnect it to a broadband the net doesn't connect. Man I wanted to use it through boradband as my broadband is faster than my wifi.
View 9 Replies
View Related
Oct 20, 2011
Network Adapter (as displayed in device manager) Realtek PCIe GBE Family Controller (says this device is working properly)I'm running my lan on the integrated network adapter "Realtek PCIe GBE Family Controller" on my motherboard. When I plug in the lan line directly from my router the speed on speedtest.net is around 2 Mbps, i have tested on 2 other computers and they all get around 10 Mbps with the same line. I build this new machine to play games, and sank $800+ on it. I am trying very hard to figure out why my LAN speed is so slow,
View 1 Replies
View Related
Mar 18, 2013
I recently updated my NVIDIA nForce 10/100/1000 mbps ethernet driver and now my computer wont connect to the internet. In fact, it doesnt even acknowledge that the ethernet chord is plugged in. I am running windows 7 and have had no problems for years now. Since ive had my PC for so long I decided it was time to update, now im at a loss of what to do. I am currently using my laptop to submit this post, as my PC is not a wifi enabled device. I recall having this problem back when I first had this computer made and found a resolution online, (cant seem to find the same site i used back then.) I recall that it had something to do with me using the command prompt. While i have been looking for an answer, I have tried the following with no avail:
Reset IPv4 TCP/IP stack to installation defaults. netsh int ipv4 reset reset.log press enter
Reset IPv6 TCP/IP stack to installation defaults. netsh int ipv6 reset reset.log press enter
Reset WINSOCK entries to installation defaults: netsh winsock reset catalog press enter
Restart the computer after.
View 1 Replies
View Related
May 27, 2012
Perhaps once a week my ethernet port stops working. That is, it is still displayed as 'working properly' in the device management screen, but it is unable to connect to dns. System restore does not solve this problem. plugging the ethernet cable in and out (10 times) does not solve this problem. Modem reset does not solve this problem either. I decided that perhaps ethernet controller is faulty, or perhaps the ethernet port in itself- so I bought a 'usb to ethernet' adaptor and surprisingly the internet connection problem persisted (during the instances when my laptop ethernet port had problems connecting to DNS, the adaptor was also unable to connect to internet).
What does solve this problem is this: I have another notebook - I plug the ethernet cable into that computer. Obviously, internet works without any problems with my second notebook. After that, I plug the ethernet cable back into the laptop which is now unable to connect to DNS. Quite often the Not being able to connect to DNS issue still remains the first time I do this, so I have to connect ethernet cable back into my second notebook and then plug it back into the notebook with a connectivity problem. After I do this 2 or 3 times, my windows 7 laptop is finally able to connect to internet.
View 3 Replies
View Related
Feb 12, 2011
have had a new HP G62-234DX laptop for about 4 months now and I'm now having problems connecting to the internet via ethernet. The lights do not come up when I plug it into the port and I have already tried to download the Ethernet driver from HP but it didn't seem to install properly, tells me it only works for Windows Vista which isn't true. I checked my device manager also and saw that I only have my wireless network adapter showing which works fine because I've been connecting wireless but I need a wired connection when I do not have wifi at my university. On device manager I chose 'show hidden devices' and I saw an unnecessary amount of "Microsoft 6to4 adapters" come up which does not seem right.
View 2 Replies
View Related
Jan 30, 2011
Everytime i plug the cable into my PC it doesn't detect it and the helper says to insert an ethernet cable.When I go to network sharing centre and check my connections it says network adaptor unplugged.im using wireless at the moment.My pc is a packard bell ipower x9810. it was windows vista but i upgraded to windows 7, i checked the packard bell website and can't find any networking adaptors. I have also checked device manager and it says - Belkin N+ wireless USB adapter #4 NVIDIA nForce 10/100/1000 Mbps Ethernet. there is no yellow exclamation mark.
View 17 Replies
View Related
May 30, 2011
i have a Dell inspiron 1520, the ethernet port has stopped working- no lights when cable connected. this was fine and then just stopped, it is used to connect to hub from time to time when wifi goes down. have tried 3 different cables, no joy, these all work in another laptop. No issues shown in control panel/ hardware. Have downloaded driver from Dell site, still nothing.
View 1 Replies
View Related
Oct 13, 2012
Have just acquired new used HP desktop running Windows Vista. System has a Broadcom NeXtreme Gigabit Ethernet card installed, which gets me to the internet OK when using a LAN cable from wireless router. But I can't make wireless connection. Vista tells me that I need a wireless network adapter.Am I missing something? Is it possible to change some settings to get the Broadcom card to go wireless? If not, what sort of adapter is needed, and is such adapter external or will it have to be installed in the system box?
View 3 Replies
View Related
Jul 18, 2011
I have a computer that is directly connected to my internet broadband service via my router and modem. From that computer, by use of a router (of course), I have a wireless connection to another desktop computer in my home, about 90 feet away.From that remote wireless internet broadband connection, I'd like to connect to yet a third computer. That third computer will be 200 more feet away. I have a direct Cat5 wire from the wireless computer desktop to that point 200 feet away. I'm thinking of adding a computer at that point.So, that raises my question: Can a computer receiving a wireless signal, then relay or transmit that signal to another computer that is "hard wired" to it via a Cat5 wire?
View 8 Replies
View Related
Sep 14, 2011
i have purchased WAG120N exactly one year back. Now I am facing a issue with modem.Power button is blinking and stabilizing after 5 minutes, but internet and wireless are not led's are not on and not receiving any signal from wireless and wired.I have called Linksys, they are not giving any support and saying one year warranty period is over.
View 1 Replies
View Related
Sep 8, 2012
I've got on-board LAN but I don't know how to use it. Am I meant to be able to surf the internet just like that if i have got on-board LAN???
View 3 Replies
View Related
Jun 27, 2011
My Internet is down. I appear to be getting power from the modem as all the lights are lit up. I have a wireless router. On my desktop I clicked on the Network icon and it said "3WIRE***" is in range but requires a Network Key (also called a WEP Key or WPA Key)? Could this be the problem? I've never had to enter a password to access my internet before. Do you know how I can find (or reset) my password? It's a D-Link router.
View 2 Replies
View Related
Apr 29, 2012
My hard drive crashed and had to reinstall my OS using manufacturers disk now everything works but the internet, the integrated ethernet card is not listed under network adapters in the device manager, its a clean install of windows xp media center edition 2005 sp2, the device manager shows no drivers missing.
View 5 Replies
View Related
Sep 17, 2012
i am using win7 64 bit on dell n5110 and my lan is not working properly. it wont even detect the cable . when i plug in the cable its like nothing happened. but when i uninstall and reinstall the driver, it sometimes resolves the issue. but i have to do this every time.
View 3 Replies
View Related
Aug 1, 2012
I have an Eee-PC and im trying to connect to the internet via my HUAWEI E173 MOBIEL INTERNET STICKWhen I plug it in it reds it, but only like a mass storage device.
View 3 Replies
View Related
Jul 6, 2012
I have network: 20 PC's conected to a switch (ordinary switch), from switch to a router (for DHCP and internet conection), Router is connected to a cable modem.
Lately an issue arised. One PC started having problem witch connection (PC is windows 7, up to date). PC instead of 192 addres is getting 169 (i need to highlight it is a problem with only one PC). That means the PC is connected to the Router but it is not getting proper IP addres. After changig the addres to static the connection ws fine for few days and then in networc connection icon (botom right) it came up with 'unidentified network' message. I changed the patchleeds, even changed the connection with known working line (from outlet to patchpanel) and the connection was coming and going. Then I changed network card with the same resoult. I noticed strange thing: While the IP is 169 or when 'unid net' when I unplug the cable from outlet then plug back and do so couple times in one moment the connection is back and stable but only for some period of time. Cables had been re terminated with new jacks and at the patch panel. Drivers for network card are up to date.
Why is the connection coming and going?
View 3 Replies
View Related
Nov 3, 2011
I'm currently volunteering at a children's group near me. They've just moved offices and are wanting a computer network in place. I have quite a bit of experience with hardware and software troubleshooting, but anything past the server is beyond me.They have a telecommunications box, as many places do, and the box has a set of patch boxes that are, according to the telecommunications people, plugged in and good to go. Each office has tunnelling on the wall with network sockets, again the norm.
View 4 Replies
View Related
Jun 23, 2012
I have found a great application that allows your PC to become a hotspot. It can also protect the wi-fi. Now remember whatever its your backend on the PC is what kind of network and speed you get such as, if my desktop connected through ethernet and I install the virtual router on the desktop than my laptop can connect to it depending on my Wi-Fi adapter on it. It could be B/G/N. B and G gives 54MBPS and N gives me 65MBPS.
View 1 Replies
View Related
