Cisco Firewall :: ASA 5505 - Can't Reach FTP Site While Inside Firewall?

Feb 26, 2011

I am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
 
Here is our current confguration:
 
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp

[code]....

View 6 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5510 - Anyconnect Client Can't Reach Inside Network

Jan 2, 2012

So, I've set up Anyconnect client access to an ASA-5510.
 
I've got a handful of interfaces, which contain hosts that should be accesible to anyconnect clients.  I'm unable to reach addresses on a specific network, due to what packet-tracer claims is an implicit deny, though I'm unsure where to apply an access-list in this case.
 
fw1# show nameif
Interface                Name                     Security
Ethernet0/0.205          SECURE                  90

[Code].....

View 7 Replies View Related

Cisco VPN :: ASA 5505 - Users Aren't Able To Reach Remote Network Through Site-to-site Tunnel

May 21, 2011

Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
 
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
 
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24

View 5 Replies View Related

Cisco Firewall :: Failover ASA 5505 - Setup Second Inside Interface On Firewall?

Feb 19, 2012

I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?

View 1 Replies View Related

Cisco :: ASA 5505 SSL VPN Can't Reach Inside From VPN Subnet

Jul 7, 2012

I've setup a SSL VPN to a ASA 5505 and can connect.

VPN network 192.168.2.0 /24
Inside Network 192.168.1.0 /24
Outside is connected to Router.

I am trying to RDP to a win server on the inside network but I cant get to it. Can not even ping 192.168.1.1 or (not sure if I could anyways) 192.168.2.1...

I added a ACL on the outside interface and then inside interface permit ip any any but still no ping or RDP...

New at VPN and have survived so far on cisco docs but this problem is evading me.

: Saved
:
ASA Version 8.2(5)
!
hostname ciscoasa

[Code]....

View 1 Replies View Related

Cisco VPN :: ASA 5505 SSL VPN Can't Reach Inside From Subnet?

Jul 6, 2012

I've setup a SSL VPN to a ASA 5505 and can connect.
 
VPN network 192.168.2.0 /24
Inside Network 192.168.1.0 /24
Outside is connected to Router.
 
I am trying to RDP to a win server on the inside network but I cant get to it. Can not even ping 192.168.1.1 or (not sure if I could anyways) 192.168.2.1...I can ping from the 192.168.1.0 net to 10.0.0.0 and 192.168.2.0 without issue but not the other way around....I added a ACL on the outside interface and then inside interface permit ip any any but still no ping or RDP...
 
: Saved
:
ASA Version 8.2(5)
!
hostname ciscoasa
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted

[code]....

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Reach Local LAN And Internet From VPN Clients

Apr 11, 2011

I'm having trouble setting up local LAN (reach inside network when VPN connected) and Internet access (reach internet when VPN connected) for my VPN CLients when they are connected to my VPN, They can connect, no problem there, but I can't reach any resources when connected. My pings time out, both to my inside network and to public ip adresses, the only thing I'm able to ping is my ASA (172.16.30.1), and I don't se any routes under "Status/Statistics/Route Details" in my cisco VPN Client (when connected).
 
Here's my config
 
ASA Version 8.0(3) !hostname KardesASAdomain-name default.domain.invalidenable password XXXX encryptednames!interface Vlan1 nameif inside security-level 100 ip address 172.16.30.1 255.255.255.0 !interface Vlan10

[Code]....

View 14 Replies View Related

Cisco Firewall :: 5505 Firewall Between HQ And Remote Site

Jun 12, 2012

we are planning on connecting a new aquired company to ours soon?We will connect the remote site to the HQ via a D3. I've been told we will need to have a firewall between them and us for a time. I was thinking of terminating the D3 connection at the remote site of 80 users. Can I use the asr as a firewall as well, to protect the HQ from the Remote site - or should I use a seperate appliance?I was thinking of a asa5505 but, am concerned with bandwidth limitations of the box?

View 1 Replies View Related

Cisco VPN :: Cannot Ping From Outside To Inside Site To Site IPsec 5505

Oct 28, 2012

I have a very basic lab site to site vpn setup where I have a ASA 5505 running v7.2(4) on one side and a cisco 2811 on the other side.

What's my issue?

I can't seem to ping from cisco router to the 'inside' network of ASA (see config below) and can't seem to ping from ASA packets leaving the 'inside' interface to cisco router even w/ an ICMP ACL permit outside in. However I'm able to ping within ASA inside network & ping cisco 2811 side w/ packets leaving ASA 'outside' interface just fine.
 
example:
-------
ciscoasa# ping inside 10.20.20.1 (to cisco loopback1 from ASA inside)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.20.20.1, timeout is 2 seconds:
[Code].....

View 6 Replies View Related

Cisco VPN :: 2901 / 2921 / 5505 ASA - Router Versus Firewall Site To Site VPN?

May 30, 2013

I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
 
1) what is the different to build site to site VPN between router and firewall ?

2) which is the best choice if using in site to site VPN connection ? 

View 9 Replies View Related

Cisco Firewall :: ASA 5505 / Site To Site VPN Using Public Addresses On Local Network

Jul 28, 2011

I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
 
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.

View 5 Replies View Related

Cisco Firewall :: ASA 5505 Site To Site RTP Traffic Is Hitting Deny All Rule?

Aug 13, 2012

Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.

Currently the rules are as follows
 
 Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny

 [code].....
 
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.

View 2 Replies View Related

Cisco Firewall :: ASA 5505 - Unable To Access Certain Ports Over Site To Site VPN

Jan 16, 2013

We have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
 
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
 
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
 
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
 
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
  
Building configuration...
  
Current configuration : 23648 bytes
!
version 12.4
no service pad

[Code].....

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Site To Site VPN Route From Multiple LANs?

Dec 19, 2012

I've set up a standard site-to-site VPN between 2 ASA 5505s and the VPN is working fine for traffic between these ASAs and computers which are in the same LANs.but when I'm trying to connect to computers which are in another VLAN I have a problem.

View 1 Replies View Related

Cisco VPN :: Site To Site VPN IPSEC Tunnel From ASA 5505 To Clavister Firewall

Nov 20, 2012

I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
 
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
 
All these remote networks are at the Main Site Clavister Firewall.

View 1 Replies View Related

Cisco Firewall :: Max Number Of Clients And Site To Site VPN Tunnels On ASA 5505

Aug 15, 2012

I wanted to know the maximum VPN client sessions (using the Cisco VPN  client) and Site-to-Site VPN tunnels that I can connect to my ASA 5505  simultaneously.
 
In other words, if I have x VPN clients and y Site-to-Site  tunnels, at any time, does x + y have to be <= 10 (Total VPN Peers)?  If yes, can I upgrade to the security plus license to increase the Total VPN Peers to 25?

Licensed features for this platform:
Maximum Physical Interfaces    : 8
VLANs                          : 3, DMZ Restricted
Inside Hosts                   : Unlimited
Failover                       : Disabled
VPN-DES                        : Enabled
[Code]...

View 3 Replies View Related

Cisco Firewall :: ASA 5505 Setup A Site To Site Tunnel?

Nov 13, 2012

I have a 5505 asa code version 8.3(2). Trying to set up a site to site tunnel with someone and he is asking if I can use ike v2. How do I go about setting up the tunnel to use ikev2? Is ikev2 an option with site to site tunnels?

View 5 Replies View Related

Cisco Firewall :: Site-to-Site VPN Between ASA 5510 And 5505 Configuration

Apr 18, 2013

I am not very experienced with Cisco networking.

Here is the situation.
 
Site A - headquarters 192.168.1.x
Site B - remote office 192.168.20.x
Site C - remote office 192.168.30.x
 
Site A - ASA 5510
Site B - ASA 5505
Site C - ASA 5505
 
Site-to-site VPN is established and works between A and B, A and C. Users would like to establish a tunnel between B and C to work on a common project and the data is on Site B.
 
I tried configuring the S2S VPN with pre-shared keys on both firewalls at sites B and C but in the end it is not established (I cannot ping either side). I used the Wizard interface multiple times and one time the CLI. I generally followed the settings chosen between the headquarter and the individual remote sites and tried to replicate them. Obviously I have made a mistake somewhere.
 
Could there be any limitation on the ASA 5505 in terms of licensing and the number of S2S tunnels?

View 7 Replies View Related

Cisco Firewall :: Site To Site VPN Between PIX515 And ASA 5505 With Dual ISP?

Apr 13, 2011

We have got site to site VPN configured between local site with PIX515 6.3(5) and remote site with ASA 5505 7.2(4) . Because of very unreliable internet connection in remote site , we have added new ISP link  which we want to use as redundant link .i understand ASA 5505 can be configured with two ISP link with SLA monitor method for redundancy as per this document ,[URL]
 
my question is how do i set up this pix 515 to have redundant VPN tunnel with remote site (when primiary ISP link fails in remote site and  secondary ISP links takes over ) .  I was thinking of using   PIX 515 with 2 peers in same crypto map used for that sepcific site to site vpn tunnel,not sure that is the right way or not though.But how would i configure ASA 5505 to use backup interface(where secondar isp router conects ) to particitae in Site to site Tunnel .

View 4 Replies View Related

Cisco Firewall :: ASA 5510 / 5505 - Site-to-site VPN One Way Access

Dec 12, 2011

We have a Cisco ASA 5510 at our main office that makes connection with a 5505 at our other office using site to site VPN. (works)
 
Now for the question,
 
we want to access our other office from the main office but we wont want them to have access to our servers etc. so basically we want to control them but they shouldn't have the rights to control us.

Is this possible with a site to site VPN? and how to do it.

View 7 Replies View Related

Cisco Firewall :: ASA 5505 Site-to-Site With UC540 Routing?

Dec 4, 2012

We are setting up a new phone system using the UC540 with a VPN connection between 2 buildings using 2 Cisco ASA 5505's at either end.The problem I am having is getting the phones at the remote site to connect to the UC540 at the main site.
 
Phones/Computers (10.0.1.0/24) -- ASA -------------VPN Tunnel------------- ASA -- UC540 -----------Data Vlan1 (10.0.0.0/24)
|------Voice Vlan100 (10.1.1.0/24)
 
What i am told by UC500 support is that the phones at the remote site will connect if they have connectivity to the TFTP subnet on the UC540, which is 10.1.10.0/30 I added the static route on the ASA and I can ping the 10.1.10.1 TFTP server on the UC540 from the ASA, but not for any other device on the 10.0.0.0/24 network, such as the DC.  I added the static route there and was able to ping, so something in the ASA seems to be preventing it. 
 
I also can't seem to get the ASA at the remote site to ping 10.1.10.1.  I've tried adding the static route there in hopes it would forward it through the VPN tunnel.

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Site To Site VPN Keep Dropping?

Feb 1, 2012

I have an issue with my site to site VPN. I have 4 sites connected  to my main HQ site via Cisco ASAs 5505 firewalls. The problem is that once and then the sites disconnected from my main site. This disconnection is not happening at the same time for the the 4 sites. For example, it might be different site each time disconnected.

View 7 Replies View Related

Cisco Firewall :: Site To Site VPN Configured On ASA 5505

Dec 2, 2012

I have a site to site VPN configured on a asa5505. The tunnel is up and the interesting traffic is successfully being encrypted. The issue is that when inbound traffic originating from a subnet outside of the encrypted range destin to the subnet within the encrypted range, the return traffic is sent into the tunnel and obviously fails.When traffic from 1.1.1.0/24 to 10.2.2.0/24 traverse the firewall the return traffic goes into the tunnel but it doesn't have the correct match parameters?Am I missing something?  I'm expecting that only traffic matching the crypto map will use the tunnel and all other traffic will utilize the default route.

View 3 Replies View Related

Cisco VPN :: Configure A Site-to-Site VPN In ASA 5505 Firewall

Dec 13, 2010

I'm trying to configure a Site-to-Site VPN in a Cisco ASA 5505 firewall which is behind an ISP router (Cisco 800 Series) configured in routing mode (not bridging) and with a static nat of all the ports to the firewall (avoiding bridging mode of the router). [code]

View 12 Replies View Related

Cisco VPN :: Site To Site With ASA 5505 And Sonic Firewall

Aug 27, 2009

I'm trying to establish a vpn tunnel with a sonic firewall.  We've checked both ends for differences and they are the same.  PFS has been disabled on both ends.  I'm seeing this in the logs.
 
%ASA-3-713119: Group = x.x.x.x, IP = x.x.x.x, PHASE 1 COMPLETED
%ASA-5-713068: Group = x.x.x.x, IP = x.x.x.x, Received non-routine Notify message: No proposal chosen (14)

[Code].....

View 4 Replies View Related

Cisco Firewall :: 5505 DNS Does Not Resolve Inside DMZ

May 14, 2012

I have a 5505 that currently has inside/outside interfaces and everything is working just fine. I am trying to create a DMZ that will essentially be just for vendors/guests. the DMZ will have full access to the outside (Internet) but no access to the inside. I am using the FW for DHCP, and 8.8.8.8 and 4.2.2.2 for DNS. I currently have 1 laptop in the DMZ vlan, and it is getting a correct IP, and it is showing 8.8.8.8 and 4.2.2.2 in ipconfig. I can ping/tracert 8.8.8.8/ 4.2. 2.2/74.125.137.147(what url... resolved to on a laptop connected to the inside vlan), but I cannot ping nor browse to url.... [code]

View 1 Replies View Related

Cisco Firewall :: Enable SIP From Outside To Inside (ASA 5505)

May 14, 2012

We recently purchases the Cisco ASA 5505 to get familiar with it, possibly buying more appliances for our branch offices. However, since the appliance is installed, our SIP telephones no longer register with our SIP service provider.
 
The SIP phones are all on 10.0.1.0/24 while the SIP provider is external via the outside network. I copied our configuration below. how to enable SIP for all 10.0.1.0/24 hosts and ports 5060, 5160, 5260, 5360?
 
gcxfw# show running-config
: Saved
:
ASA Version 8.4(3)

[Code].....

View 2 Replies View Related

Cisco Firewall :: 5505 DMZ To Inside ASA 8.4 / ASDM 6.4

May 21, 2012

I have a standard ASA 5505 with inside, dmz and outside with the default security levels, 100/50/0. we have an email server inside which has been NATed and is working fine. However users accessing the wireless on the dmz are unable to access their emails on https (443). How do I allow SSL access ONLY to users on the dmz using ASA 8.4 commands or ADSM 6.4?

View 10 Replies View Related

Cisco Firewall :: ASA 5505 Ping Inside To Outside Don't Go

Sep 29, 2012

I have 2 ASA and would like to build a Side-to-Side VPN between these ASA. So I can learn something about configure a ASA for different thinks. But now I don`t can Ping from a Client to the Internet-Router.My Configuration is:
 
Client IP 192.168.1.100 <===> ASA Inside 192.168.1.1 /Outside 192.168.178.254 <===> Router 192.168.178.1
 
Is there something wrong at my config? or do I need inside private Adresses and at the Outside Global IP`s.
 
At the Router I have a Static Route that the 192.168.1.0 / 24 ist to find over Gateway 192.168.178.254

View 2 Replies View Related

Cisco Firewall :: ASA 5505 - Allow (outside) Host To (inside)

May 20, 2011

I have a ASA 5505 Sec Plus. I would like to allow outside hosts to our mail server and also our FTP server. So i would like to allow only SMTP, HTTP (for Outlook Web Access) and FTP.

View 10 Replies View Related

Cisco Firewall :: NAT With Inside / DMZ VLANs On ASA 5505 V8.4(2)?

Sep 16, 2012

I have a 5505 with Base license running ASA software v8.4(2) that has been working happily for a while with an inside and an outside VLAN.
 
The outside has a single statically configured public IP, and I have a number of static NAT rules to expose a few internal servers as well as Dynamic-NAT for all devices on inside to gain access to the Internet... the main bits of the config are below:
 
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
!
interface Vlan2

[code]....

I now have a requirement to add a "dmz" VLAN for guests to have access to the Internet using a dedicated wireless AP, but not to any of the inside resources. As the ASA has a base license I have configured "no forward interface" to the inside vlan, which suits the purpose fine
 
interface Vlan12
description Used only for guests access to the Internet - no access to the corporate resources
no forward interface Vlan1
nameif guests
security-level 20
ip address 192.168.2.1 255.255.255.0
 
My problem is that when I try to add NATing from the dmz to the outside I get a:
 
     ERROR: Address a.b.c.d overlaps with outside interface address.
     ERROR: NAT Policy is not downloaded
 
with either:
 
object network guests_subnet
subnet 192.168.2.0 255.255.255.0
nat (guests,outside) dynamic interface

[code]....
 
Having had a look at the ASA Configuration guides, all the examples I can see with several "internal" VLAN's being NAT'ed use one external IP per VLAN - is this a feature/restriction of the ASA software? Are there any workarounds? Or is the overlap in the error message really about the current NATing to the inside VLAN which is done on the "any" 0.0.0.0 subnet - would the following then work:
 
object network obj_any
subnet 192.168.1.0 255.255.255.0
nat (inside,outside) dynamic a.b.c.d
object network guests_subnet
subnet 192.168.2.0 255.255.255.0
nat (guests,outside) dynamic a.b.c.d

View 5 Replies View Related

Cisco Firewall :: Connect Inside To Outside In ASA 5505?

Apr 2, 2013

I have a test ASA 5505 with the setting below:

How can I connect to the internet (Vlan 1 to VLan 11)
 
[code]....

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Router In Second Inside

Jul 19, 2011

I have an ASA 5505 with the typical inside/outside interfaces.  I also have a DMZ that I've named remote for all of my ISP VLAN'd remote offices to connect.  I've set the security levels on both the inside and remote interfaces to 100.  From remote 192.168.71.0 network I can ping to the remote interface on my ASA, 12.230.129.66/8, but can't ping anything on the inside network, 192.168.1.0, or the web. From my ASA I can ping the router directly attached to the remote interface, 12.233.136.162/8.  From my inside 192.168.1.0 network I can hit the web fine, but cant ping the remote router 12.233.136.162 or the remote network..
 
I dont' know if I missing something with routing, or with the two interfaces w/ same security...or what?
 
Here's my config. I've also attached an awesomely bad network map.
 
Result of the command: "wr t"
: Saved:ASA Version 8.2(5) !hostname ciscoasadomain-name wec.wnetenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2switchport access vlan 3!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip [Code]...

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved