D-Link 14dBi Outdoor Direct Antenna Extension Cable For This Product?
Aug 19, 2011Anybody know of a extension cable for this product? D-Link 14dBi Outdoor Direct Antenna (ANT24-1400) I need at least 10-15 feet of extra length.
View 1 RepliesAnybody know of a extension cable for this product? D-Link 14dBi Outdoor Direct Antenna (ANT24-1400) I need at least 10-15 feet of extra length.
View 1 Repliesproviding an extension for the below antennas cable length for project related requirements with the AP 1262.
AIR-ANT2506 2.4 GHz, 5.2 dBi Mast Mount Omni Ant w/RP-TNC Connector
AIR-ANT5160V-R 5GHz 6dBi Omni Antenna w/RP-TNC connector
Any cheap outdoor extension antenna that works with a Linksys wap54g? Not looking for anything too expensive. Just trying to bring wifi signal into a building.
View 1 Replies View RelatedI'm looking to extend wireless coverage outside the building and was think of using 2600e APs with AIR-ANT2566P4W-R patch antenna mounted externally.Is this a valid combination?
I've had a look through various bits of documentation and this antenna seems to be supported but can't see documentation that details of what low loss cables and lightening arrestors are compatible.
I want to install some AIR-ANT2566P4W-R antennas outdoor against the wall, the 2602e access points will be mounted on the interior side of the wall, altough the wall is 30cm thick, so I need some antenna extension cables.What type of coax extension cables would be recommended ?
View 1 Replies View RelatedI am installing 60 meters of overhead telephone cables between two buildings. which is better cat5 or cat 6 in terms of durability?
View 3 Replies View Relatedi want to transfer files, remote desktop, lan gaming....actualy lan gaming works fine without doing anything just connecting the cable
but how do i transfer files and remote desktop....what software do i need?
note:
pc1 windows 7
pc2 windows xp
The WRP-400 router has two phone ports - does it support direct calls between them?
View 1 Replies View RelatedI have a new router (ASUS RT-N10)and It is asking me to direct connect my cable modem to my computer, and then find my MAC address via command prompt, and clone it to the new router.I can get to my command prompt, the problem lies in windows 7 and vista's (or mine) inability to realize that my network card is directly connecting to the modem. (No internet connection available, doesn't think anything is connected). I have tried on multiple machines to try and find my modem's mac address but it simply is not working.I want to know if I can find the mac address through the old router, or what I need to do to have windows 7 recognize I'm directly connecting the modem to the PC.
View 3 Replies View RelatedIs it possible to access the internet directly using the provider's hdmi cable routed through a generic device?
View 3 Replies View RelatedCurrently have two laptops: one is a MacBook using OS X, the other a Gateway PC running Vista Home Edition. A Dell Inspiron 17R notebook running Windows 7 Home Premium is in process of delivery. Current laptops linked on a home Wi-Fi network with AirPort Express router. Anticipated use of new Dell notebook requires its direct connection to Internet outside of current network configuration. Is it possible to have both accesses available in my setup utilizing my one cable high speed service connection? If so, what are the steps needed to accomplish the required setup?
View 1 Replies View RelatedHave high speed cable and find that the wireless speeds using Speedtest.net are faster than when hooking directly into the E4200. Do I have something set incorrectly?
View 3 Replies View RelatedI cannot connect my Dell Inspiron 1300 through the NetworkManager "wired" connection, when I try to go direct to the cable modem. It fails to connect. If I connect the cable modem to my (linksys WRT54GS) wireless router, and then connect my laptop to a wired port in the router, it connects in seconds, successfully, This has happened to me 2 other times, when I tried to connect my laptop to a client's cable modem, because my client did not have a wireless router available, in their home. My wireless works fine. This has me perplexed. I'm using Ubuntu 10.04 LTS and NetworkManager Applet 0.8, I've tried some things to see what is going on, such as "ifconfig" "dhclient" as well as modifying the "Auto eth0" parameters and adding my laptop's MAC address, etc.
View 5 Replies View Relatedwe got a dark fiber betwwen two sites away from each other 30 Km,i need to connect this sites acts as backup dc to main dc in main site using cisco 4900 Switches in BK-DC anf 6513 in the main site,how can i verfiy if this fiber oparates as L2 and i can extend vlan servers,is it via "sh cdp neigh" and "sh vlan br"?
View 2 Replies View RelatedWhere can you get a replacement lens for the DCS-70 Outdoor enclosure?
View 3 Replies View RelatedLet's say, an antenna like that Should I open the modem and therein there could be a slot for it to be plugged in? Because on the back side of the modem none of the slots will suit such plug.
View 2 Replies View RelatedI have a Linksys WAG 120 N wireless router with an internal arial. I want to strengthen the signal to my laptop 2 rooms away as it keeps dropping out. Is it possible to change WAGGING from internal to external antenna to increase range/performance?
View 1 Replies View RelatedFeature AIR-CAB020LL-R AIR-CAB050LL-R AIR-CAB100ULL-R AIR-CAB150ULL-R Cable Length 20 ft (6 m)50 ft (15 m)100 ft (30 m)150 ft (46 m) Transmission Loss 1.3 dB3.4 dB4.4 dB6.6 dB for Cisco 1941W router with external antennas?
View 3 Replies View RelatedI just got another DCS-930L. I have set these up to work wirelessly before but my question is why can't I connect it directly to my ethernet port and be able to get into the web interface by typing the default IP address without using a utility or installation software? I have tried to assign a manual IP to it but that didn't work. So here is what I want to do: Plug the camera into the ethernet port of my MacBook Pro and just view what the camera sees.
View 7 Replies View RelatedI've just got my DCS-2121 up and working. But i can't figureout how to access the direct URL for the camera?And is there a URL for still images aswell?I got an iPad and an iPhone, but i can't access the camera because it use Java.I had another DCS-900 where i could access IMAGE.jpg and Video.cgi. Is there anything like those for the DCS-2121?
View 7 Replies View RelatedWe have the Cisco WRT54G wifi router in many offices in this building. This router has two antennas. These antenna are screw into the back of the router unit. The antenna is male and router side is female of the connector. what are these connectors (some type of RF connectors)? How can we get extension cables for these to move the antenna from one fix location to another point?
View 4 Replies View RelatedI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedI have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
I just bought a DCS-2130 for outdoor use (city landscape through my window in the nineteenth floor), and I'm trying to get it work during the daylight, but I'm having some problems.It seems like this camera can't handle direct sunlight, and in these situations the image gets blurry, even when I set the exposure to auto with max of 0dB in setup menu. Simply there's nothing I can do in this options menu to solve this problem.As the day passes by (and the sunlight gets weaker), the image gets better 'til the night, when it's perfect.What I need to know is if there is any way to setup it properly for daylight use. Is there possible to setup these exposure parameteres some other way, like editing an .ini file or something like that? Or this expensive camera simply can't handle this?
View 7 Replies View RelatedI just bought a DIR-815 and wanted to upgrade the antenna's. Unfortunately I can't figure out how to remove them. Typically you can unscrew the antenna's on similar products. But DIR-815's seem firmly attached.
View 6 Replies View RelatedI have a Dir 655 router how can I know if one of the antennas is working right?
View 5 Replies View RelatedHow to add an external antenna? I'd like to mount a DCS-930L in a location (inside a metal housing) that would need the antenna to be a few inches away. Any internal layout information?
View 3 Replies View RelatedIf the antenna for this router is removable? The model I have doesn't seem like it is and I am afraid that I might break it if I try. I would like to connect an external antenna I have.
View 4 Replies View RelatedHow can I attach an optional antenna to a Dir 615 router?
View 1 Replies View RelatedI know there a lot of threads on antenna for the DIR-825 but my question is ....does any antenna RP SMA are compatible with this router ? url...
View 3 Replies View RelatedI have tested each antenna separately. With each antenna attached one at a time the left and right antenna is giving me -20 signal. The center is only giving me -65 signal. Is this a problem with the router or normal? I noticed that the center pin is pushed in more then the left and right. Don't know if that is the cause.
View 14 Replies View RelatedWhat is the 5GHz antenna orientation in the DAP-1522? If I want to get the best signal for streaming to a DSM-750 how should I orient the the DAP-1522? Horizontal? Vertical? and which edge towards the media player?
It's working but the access point only reports about 50% signal strength over 20 feet (and only 1 wall) so I would have expected better. I've tried turning the box a couple of different ways but didn't see any big difference in the reported signal strength.
This may sound ignorant but I cannot get either of the antennas off my 615. They are listed as removable reverse SMA but they are so tight I am afraid of damaging it. This is my second 615 after not being able to get one of the antennas off the first. D-link said they should just unscrew but I cannot get either of them to budge. D-link support said the one I had first must have been manufactured wrong so I returned it to new egg and got a new one. Same issue. I need to have an external antenna on the unit.
View 11 Replies View Related