Linksys Wireless Router :: E4200 Upgrade 1.0.03 Stuck At 98%
Nov 13, 2011
I downloaded the firmware from the Linksys site. I'm using IE v9 on a Win7 Pro x32. I'm using the E4200 as an access point so DHCP is disabled, no cable in the WAN port.
I uploaded the firmware but it seems to be stuck for 30 minutes at 98%. I read some threads saying it takes a while, but I'm not sure if it is locked up. The screen says not to interrupt the process so I don't want to reboot/reset and brick the router.
I've tried to upgrade/downgrade process twice with the same result. After few days without any issue 2.1.39.145204 gets stuck (=routing to internet doesn't work although I can ping from wireless network to all LAN IPs) and I need to reboot the router.
I have about 7 devices. Guest network is disabled, parental control is disabled, USB is not used, DHCP service is used, WPA2 mixed personal mode is used, MAC filtering is disabled, DMZ is disabled, DDNS is disabled, port triggering is not used. All the rest of settings are in default values.
As far as I notied the previous version 2.1.39.144146 doesn't get stuck at all.
is it worth it? I still cant stream some of my higher quality 6+gb .mpg video files with the v1 with the .03 firmware. I notice the v2 says faster or better HD video. [URL]
The file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
I can't see my network shares after upgrade altough everything works fine , the network scanner shows all the atatched devices but in Eplorer when I click Network there is nothing shown on two computers running Win7 64.I did downgraded the firmware back to .01 but still no network .
I was using a netgear wndr 3400 and my network stream never failed. i bought a e4200 v2 and my tv loses streaming capabilities after about 10 to 15 minutes.i have to turn it off to get them back and then it does it again in 15 minutes. i know it is not the tv it wprked fine before the new router.
I just bought a Cisco E4200 (from someone on Ebay, so returning is probably not an option). I was in the process of setting it up when it wanted to do a Router Update. Unfortunately, it did not specifically say to not do it WIRELESS. We had a disconnection in the upgrade process. Now the Power light just blinks. I can ping it from a hard-wired PC, but cannot get to the Administration Web page to retry the firmware update (I did download it from the site). Also Cisco Connect cannot connect to the router.
Oh Yes, I have tried holding reset button for 30 seconds, unplugging for 30 seconds, and replugging in the router. I do not get any different results.
I have a 1121 autonomous AP which I switched to the lightweight mode by copying the LWAPP ios to its flash and issuing the command boot system flash IOS_file_Name. After that I was unable to associate the AP to my wireless controller because it was continiously rebooting. Unfortunately this AP does not have a console port so I can access the debug and see what is happening. And I was not able to switch it back to the autonmous mode becaus the AP won't accept the Autonomous mode IOS anymore.
I have a WRT 54G2 v1.5. On the status page it shows the address as 127.0.0.1 subnet mask 255.0.0.0. On the setup page the router is setup to use DHCP, with an IP address of 192.168.1.1. I have reset the router several times and flashed the firmware (once) to the latest version.
I have a LinkSys WRT 160 N wireless router, the router just stopped starting abruptly, when i power cycle the router, all the 4 ethernet light come on, and that is where it gets stuck. I've tried using the reset button but there is no effect after i depress the button.
since last nite my router E1200 has been having speed up and down problems.first it goes to 150mb/s then back down to 1 for a few minutes, usualy its stuck at 72mb/s which is a far cry from its rated 300mbps but qi'd rahter have that than 1-2mbps.i'd be happy with 150mbps but that only lasts 5mins then goes down to 1-2mbps and i have to reset my connection.
I have bought a new WRT54G2 router since the old one broke down. When I log into the 192.168...and click wireless, it takes me to this window that says Searching for your Client Device....If you haven't clicked wi-fi protected setup button please do so now. It's stuck at 98% and I click on the bottom middle button with the 2 arrows constantly and nothing is happening.
When trying to connect (wireless or wired), I can't get past the authenticating status. Have used this computer with same router for 3 years. If there was ever a problem, I would unplug/replug the router.I am currently connected through my neighbor's unsecured network.
My WAG120N router overheating and stuck repeatedly every 4-5 hours. How i can solve this problem? I buy this router 3-4 months ago...Is hardware or software issue?
My WAG120N: Firmware Version: V1.00.07 DDNS Service - Disable DMZ Hosting - Disable Firewall - Disable Restore to Factory Setting - Many Times = No result Connected Computers in the LAN - WLAN = 6 Desktops-Laptops, 3 PDA Devices
--> My Router gives this information about my Downstream / Upstream Rate Downstream Rate: 10229 kbps Upstream Rate: 861 kbps
I bought a v1. wusb600n for win XP sp3, recently for no apparent reason, it became stuck in country region #2 (ch 36 to 64) when i use WZC or even netstumbler to view networks. I have tried uninstall/reinstall of driver, tried using ralink's driver and even another usb600n, but the problem remains.
Checking the INF files shows that all the drivers are trying to install as region #0 (36-64 + 149-165) but they are always showing as region #2
I have a recurring issue with my e4200v1. My wired and wireless connections work fine, but I can't get to the administration website. I have https only set up, and after I get thru the 'certificate error' screen, I get an error that says web page is unavailable. Firfefox tells me that the connection was lost - error 101.I have tried wired and wireless, multiple computers, multiple browsers. I even turned the firewall off on one computer (or I think I did anyway).The only way I know how to fix it is by completely resetting then setting up the router all over again.
Upgraded from WRT610N to E4200. Since upgrading to latest firmware the wan just disappears both 5 and 2.5 Ghz bands. Happened with older firmware but not as often. Using it in briged mode. When this happens I can't even get to the management page with a lan connected pc. Have to do a hard reboot to get it to respond again. This is unacceptable for a router at this price point.
The PW has been changed, I got the new one correct but upon entering it on my laptop it goes around circle showing,"Wireless network detected" and then,"Unable to connect to preferred wireless network".It never works. I don''know haw to fix this problem. It did not happen on my iPad.
I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
I bought Linksys E4200, at a time that is the TOP of the line Cisco routers for Home use.I noticed a serious usage issue with it, I could not identify which are the wifi devices connected to choose for access restriction or parental controls, as the dialog box state only as "Network device", and software control by Linksys does not have any provision to use MAC ID or any other option "except " looking at the dialog box as "Network device".
Trying to update it to the new smart Wifi but getting this error "Incorrect Image File".Yes Ive tried redownloading yes ive tried different browers and yes to unziping the file! and Yes Im downloading the correct version I even tried version 1 for the heck of it and still nothing.
I just received by replacement e4200 v1. I updated the firmware to 1.0.03 build 14 and am up and running just fine. The specs say e4200 should be 300+450Mbps. I am using a software "inSSider 2.0" to view my wireless setup. I get 144(N) at 2.4GHz and 450(N) at 5.2GHz. Please note these are max bit rates and not connect speed or throughput rate. The "inSSider" software gives me the following:
I get this information by hovering on the max bit rate field on the row displaying my SSID. So is it correct to say that my e4200 is not designed to reach 300Mbps at 2.4GHz. There is an earlier discussion thread about connection maxing out 144. Please note I am not talking about connect speed or thru-put speed. Max design bit rates of dual band router labeled e4200.
Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
Firmware 1.0.00 on my E4200 Hardware v1.0 provided a functioning 6to4 tunnel through Comcast's 6to4 facility. Windows and Linux clients on my local network discovered IPv6 addresses and were able to use them successfully.Unfortunately, after the upgrade to 1.0.03 this functionality was gone. I missed reading the ChangeLog, which said that the automatic tunneling feature was removed in 1.0.01. The now provided IPv6 functionality works much less well. First, automatic configuration (discovery of the 6to4 via IPv4 anycast) no longer works with Comcast's gateway. If I configure the tunnel manually, by specifying a 2002/16 prefix, I regain IPv6 connectivity, but only for Linux clients on my local network.
Windows 7 clients suffer from the problem that because the E4200 hands out ULA addresses, they end up preferring those ULA addresses when making global IPv6 connections in the IP 'source' field, which of course does not work. It's like putting your company mailbox code as the return address on a letter you send via US Mail. Other home routers, such as the AVM Fritz! (url,...) suffer from the same problem. However, they provide an option to turn off ULA at the router.Is it possible to turn off ULA for the E4200?
I have a E4200 router v.01 and when i updated the latest firmware (due to security exploit) it seems that whenever i acess the router settings (192.168.1.1) it doesn't ask me nor to input the admin and the password anymore, using wifi or wired.. I want the usual proccess whenever i go to 192.168.1.1 it will ask me to input my admin and password to change my router settings..
I have an E4200 and the Cisco VPN client on my home computer that I use to access a work network. The VPN client cannot connect unless I either (a) bypass the E4200 and connect directly to my cable modem or (b) disable the SPI Firewalls on the router. I have all the VPN passthroughs set to "enable" on the router, but still cannot connect. The VPN client is using IPSEC over TCP on port 10000.
I've been trying to get FTP Running up on my router for some time now.
I know my current WAN address and have setup a specified folder on my E4200 for the FTP partition. A username for myself has been created with login info and I have forwarded the port I have specified on my router's FTP configuration page.
I try to log into the server, but whenever I try to log into it, I keep getting a "incorrect login information" message back at me.
If I cancel out of that then I get an error message saying it can't find the specified folder and to check the address of the server.
I know the login information information is correct and I've tried changing the password to others of varying lengths.
I've also tried changing the port I'm running the FTP off of incase my ISP has blocked that port, nothing works.
