Linksys Access Point :: E4200 - How To Upgrade
Jan 30, 2011upgrading to an E4200 router. What would be the best wireless access point to use with that?
View 6 Replies
ADVERTISEMENT
Linksys Access Point :: E4200 / E1500 - Cascading Routers Versus Access Points?
Nov 24, 2011I am trying to find an effective way to extend the wireless signal across our home. I have tried various different solutions. Currently, I have an e4200 primary router that is cascaded with two additional e1500 routers that have been configured as access points. The Linksys support team hosted my computer and configured the devices. The e1500 routers are connected via ethernet wires running through the walls. And, this seems to be working well. Here's my question. The e1500 routers are configured with different SSID names, which Linksys advised was required to avoid conflicts in communications from the three router devices. Is there any way to configure this set up or something similar so that the entire wireless network has the same SSID and is seamless. In the current configuration, I have to specifically connect to the primary router or one of the two access points.
View 3 Replies View RelatedLinksys E4200 Can't Ping New Access Point
Jul 4, 2012I have a Linksys e4200 and a EnGenius EAP300. I setup new EnGenius AP to 198.162.1.5 and the Linksys is 198.162.1.1. The two devices are connected with Ethernet capble with a POE switch in the middle. Internet connection thru the Linksys works fine. However, the EnGenius does not connect to the Ineternet (Gateway is set to 198.162.1.1) Also when connected to the Linksys, I cannot ping the EnGenius.
View 1 Replies View RelatedLinksys Access Point :: Can't Access WAP54G After Firmware Upgrade
Apr 30, 2012I just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.
View 1 Replies View RelatedLinksys Access Point :: How To Upgrade To The Wap54g
Dec 31, 2011i have been using a couple of wap54g units for years now (awesome units!) but its now time to upgrade to "N".is there a newer unit that has "N" ?is there a unit that has a PoE option? also, i really like the ability to switch to larger antennas like the wap54g unit does. i would think that all wireless access units should have removeable antennas and a PoE option!
View 6 Replies View RelatedLinksys Wireless Router :: Turning An E4200 Into Access Point?
Jan 22, 2012I have broadband internet coming into 1 room of my home. The internet goes through a router I have set up, its a Linksys WRT54G2 (router #1), Firmware version 1.0.04. Everything on this works fine, I'm able to get my TV and laptop in a different room to access the router wirelessly without any inconvenience.In another room I have a regular desktop computer which I would like to get internet on. As well as other devices, so I purchased another router, this time a Linksys E4200 (router #2) in hopes of turning it into an access point.Now I've set up LAN's in the past, using the actual cable plugged into the second router, problem is in this scenario I can't run a cable over to router #2. Both computers use Windows 7. Both router's drivers and firmware have been updated on the Linksys page, all my Windows drivers are updated, etc. I checked other forums for similar questions and although there are some, they date back to 2009 as well as Google which has some websites dating back to 2006! While useful, I wasn't able to find something that details how to solve my problem with my specific setup. I've already gone into router #2 and changed the router's IP to 192.168.1.2 and also turned DHCP off, problem is, once I take that router off into the other room, it doesnt connect to primary network or allow devices to even "see" router #2.
View 2 Replies View RelatedLinksys Access Point :: WAP54G As Range Expander For E4200?
Jun 25, 2011I have just bought a E4200 and updated to latest FW version 1.0.02-Build13 It works very well for me so far But in the repote part of my home, the signal is too weak :-(
I have a WAP54G (HW-rev-2), which I would like to use to expand my wireless range, but so far I have not been able to get a setup where I can see the wireless coverage expanded. I have placed the WAP54G inside the wireless coverage range of the E4200 with good signal level.
I have tried various setup combinations and searched articles, but so far I have not been able to get this working as expected..
Before I spend more hours on this or decide to dump the WAP54G, I would like to know if this setup is at all possible with these components, - and of course if there are any hints to get this working ?
Linksys Wireless Router :: E4200 As Access Point / Bridge Mode?
Sep 6, 2011I have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
Linksys Access Point :: E4200 Discover New IP Address Of Reconfigured Router
Feb 14, 2013I have changed from a DSL internet service to a Comcast cable system. I have setup my E4200v1 router as an Access Point, to extend coverage in my building. It works fine, but I can no longer log on to the unit using its' IP address 192.168.1.1. The browser returns the message "Internet Explorer cannot display the webpage." If I want to tweak the settings the only thing I can think to do is to push the reset plug, back to factory settings and go through the whole process. Is there a way to discover the new IP address of the reconfigured router? I left the default address as it was when I made the changes to AP status.
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Access Point To Maximize Coverage Throughout House
Jan 27, 2012I bought two E4200s with the intent of using the second as a wireless access point to maximize coverage throughout my house. I just learned the hard way that the E4200 doesn't support that feature, and will only act as an access point if physically connected to the primary router that is connected to the internet.
Before I spend even more money on equipment, I was wondering if any of the experts here can tell me whether I can use a Linksys Bridge, like the WET610N or WES610N, to operate the second router in bridge mode and turn it into a wireless access point?
Linksys Wireless Router :: E4200 / E3200 Or E2500 Better For Home Access Point?
Jan 18, 2012I am looking form accesspoint for home network. I do not need router and usb functionality, I have this already in my linux server. I need only wifi accesspoint with 2 bands and 300Mbps bandwith. Is there a big difference between E4200 or E3200 or E2500? I know that E4200 supports 450Mbps, but I am not planning to buy new devices which could go faster than 300Mbps. Beside of technical parameters in technical specyfication is there a difference in wifi bandwith or tranmission between wifi and cable network?
View 9 Replies View RelatedLinksys Access Point :: Can't Find WAG160N Firmware Upgrade Download Page
Dec 23, 2009Can't find WAG160N firmware upgrade download page on this site A few mounth ago it existed
View 3 Replies View RelatedLinksys Access Point :: Connect And Configure WAP54G Access Point To New Cable Modem?
Nov 1, 2012How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedLinksys Access Point :: WRT54G - Unable To Find Access Point In Home Network
Aug 29, 2009I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
Linksys Access Point :: WAP54G Access Point Setup After A Reset?
Jul 9, 2006I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedLinksys Access Point :: WAP54G Possible To Downgrade Firmware From Access Point
Jan 17, 2013I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedLinksys Access Point :: WRT320N Access Point Vs Range Extender
Dec 14, 2011Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedLinksys Access Point :: WAP4410n MIBs Or OIDs For Access Point
Jul 3, 2012I have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedLinksys Access Point :: WAP54G Access Point Unable To Connect To More Than One PC?
Apr 25, 2011I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
Cisco Wireless :: 602-OEAP Access Point Broken After WLC Upgrade To 7.4.100.0
Mar 7, 2013I have a TAC case open, but it doesn't seem to be making any progress.I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0..Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, but they won't broadcast the WLAN.An interesting thing, on the 602 AP, in the log, I see this:*Mar 06 15:08:12.667: SSID remote, WLAN Profile Name: RemoteOEAP, added to the slot[0], disabled..So the AP is definately talking to the WLC and being pushed the correct WLAN profile.On the controller, the AP shows the the Admin status of the radios is showing DOWN, but the Admin status on the AP itself shows UP
I've done a factory reset on the APs to no avail. I have a 2504 WLC as well that i'm in the process of implementing in a DMZ specificially for these APs, and for testing purposes, I associated the 602 Ap to that WLC as well. This one is running 7.4.100.0 too, same results. It would appear to be a problem with this version of software?
Cisco Wireless :: AIR-WLC4402-50-K9 - Access Point Not Coming Up After Upgrade Image
Sep 18, 2011I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is 7.0.116.0 (default) 7.0.98.218 (active) so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its 7.0.116.0 (default)(active) 7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting.
Cisco Wireless :: 3502I Access Point Unsuccessful Software Upgrade
Jan 16, 2013I have a trouble with AIR-CAP3502I-R-K9 AP.I tried to upgrade IOS software in ap because it was connecting and disconnecting to controller too often. I already upgraded one of two access point and it working stable at this time, but the second one not. [code] So, I even can't load new software. What can I do now?
View 19 Replies View RelatedLinksys Access Point :: Repeat WAP54G Access Point?
Aug 25, 2011What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedLinksys Access Point :: WRT120N - Cannot Connect To An Access Point
May 10, 2013I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Linksys Access Point :: Configure WRT120n As An Access Point?
May 1, 2012Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedLinksys Access Point :: E3000 Configuration As Access Point?
Apr 6, 2011I have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedLinksys Access Point :: Way To Find Mib For WAP54G Access Point?
Feb 10, 2012I have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedLinksys Wireless Router :: How To Upgrade From V1 To V2 E4200
Jan 3, 2012is it worth it? I still cant stream some of my higher quality 6+gb .mpg video files with the v1 with the .03 firmware. I notice the v2 says faster or better HD video. [URL]
View 5 Replies View RelatedLinksys Wireless Router :: Can't Upgrade Firmware On E4200
Oct 18, 2012The file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
View 2 Replies View RelatedLinksys Wireless Router :: E4200 Upgrade 1.0.03 Stuck At 98%
Nov 13, 2011I downloaded the firmware from the Linksys site. I'm using IE v9 on a Win7 Pro x32. I'm using the E4200 as an access point so DHCP is disabled, no cable in the WAN port.
I uploaded the firmware but it seems to be stuck for 30 minutes at 98%. I read some threads saying it takes a while, but I'm not sure if it is locked up. The screen says not to interrupt the process so I don't want to reboot/reset and brick the router.
Linksys Wireless Router :: How To Upgrade Firmware On E4200
Jul 2, 2012I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.
Linksys Wireless Router :: E4200 Can't See Network Shares After Upgrade
Apr 21, 2012I can't see my network shares after upgrade altough everything works fine , the network scanner shows all the atatched devices but in Eplorer when I click Network there is nothing shown on two computers running Win7 64.I did downgraded the firmware back to .01 but still no network .
View 3 Replies View RelatedLinksys Wireless Router :: Tv Losing Network After Upgrade To E4200
Mar 15, 2013I was using a netgear wndr 3400 and my network stream never failed. i bought a e4200 v2 and my tv loses streaming capabilities after about 10 to 15 minutes.i have to turn it off to get them back and then it does it again in 15 minutes. i know it is not the tv it wprked fine before the new router.
View 5 Replies View Related